Hirschmann BATOne User manual

User Manual
Installation
Managed IP67 Wireless Switch
BATOne
Installation BATOne
Release 01 01/2019 Technical Support
https://hirschmann-support.belden.com

The naming of copyrighted trademarks in this manual, even when not specially
indicated, should not be taken to mean that these names may be considered as free in
the sense of the trademark and tradename protection law and hence that they may be
freely used by anyone.
© 2019 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying,
reproduction, translation, conversion into any electronic medium or machine scannable
form is not permitted, either in whole or in part. An exception is the preparation of a
backup copy of the software for your own use.
The performance features described here are binding only if they have been expressly
agreed when the contract was made. This document was produced by Hirschmann
Automation and Control GmbH according to the best of the company's knowledge.
Hirschmann reserves the right to change the contents of this document without prior
notice. Hirschmann can give no guarantee in respect of the correctness or accuracy of
the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the
network components or the associated operating software. In addition, we refer to the
conditions of use specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product
site (www.hirschmann.com).
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Installation BATOne
Installation BATOne 01.01.2019

Contents
SAFETY INSTRUCTIONS
6
ABOUT THIS MANUAL
12
KEY
13
1
DESCRIPTION 14
1.1
General description 14
1.2
Device name and product code 15
1.3
Device view 16
1.4
Power supply 17
1.5
Ethernet ports 17
1.5.1 10/100 Mbit/s twisted pair port 17
1.5.2 1000 Mbit/s F/O port 17
1.5.3 Pin assignments 18
1.6
Connections for antennas 18
1.7
Display elements 18
1.7.1 Device state 18
1.7.2 Port status 19
1.8
Management interfaces 20
1.8.1 USB interface 20
1.8.2 V.24 interface (external management) 21
1.9 Signal contact 24
Installation BATOne
Release 01 01/2019 3

2
INSTALLATION 25
2.1
Checking the package contents 25
2.2
Installing and grounding the device 26
2.2.1 Installing the device 26
2.2.2 Grounding the device 26
2.3
Installing the antennas 27
2.4
Connecting the ferrite 28
2.5
Connecting the power supply and signal lines 29
2.5.1 Supply voltage (100 V AC... 240 V AC, 50 Hz / 60 Hz)30
2.5.2 Signal contact 30
2.6
Operating the device 31
2.7
Connecting data cables 31
2.8
Filling out the inscription label 32
3
MAKING BASIC SETTINGS 33
4
MONITORING THE AMBIENT AIR TEMPERATURE34
5
CONFIGURING THE TRANSMIT POWER 35
6
MAINTENANCE AND SERVICE 37
7
DISASSEMBLY 38
8
TECHNICAL DATA 39
8.1 General technical data 39
Installation BATOne
Release 01 01/2019
4

8.2
Power consumption/power output 40
8.3
Dimension drawings 41
8.4
Radio technology 42
8.5
Roaming 42
8.6
Receiving sensitivity, transmit power, and data rate of the WLAN
module version EWLAN1 43
8.6.1 IEEE 802.11b 43
8.6.2 IEEE 802.11g 43
8.6.3 IEEE 802.11a 44
8.6.4 IEEE 802.11n 44
8.7
EMC and immunity 46
8.8
Network range 47
9
SCOPE OF DELIVERY, ORDER NUMBERS AND
ACCESSORIES 48
10
UNDERLYING TECHNICAL STANDARDS 50
A FURTHER SUPPORT
51
Installation BATOne
Release 01 01/2019 5

Safety instructions
WARNING
UNCONTROLLED MACHINE ACTIONS
To avoid uncontrolled machine actions caused by data loss, configure all
the data transmission devices individually.
Before you start any machine
which is controlled via data transmission, be
sure to complete the configuration of all data transmission devices.
Failure to follow these instructions can result in death, serious
injury, or equipment damage.
General safety instructions
You operate this device with electricity. Improper usage of the device
entails the risk of physical injury or significant property damage. The
proper and safe operation of this device depends on proper handling
during transportation, proper storage and installation, and careful
operation and maintenance procedures.
Before connecting any cable, read this document, and the safety
instructions and warnings.
Operate the device with undamaged components exclusively.
The device is free of any service components. In case of a damaged or
malfunctioning the device, turn off the supply voltage and return the
device to Hirschmann for inspection.
Internal fuses are triggered only in the case of a detected error in the
device. In case of damage or malfunction of the device, turn off the
supply voltage and return the device to the plant for inspection.
Qualification requirements for personnel
Only allow qualified personnel to work on the device.
Qualified personnel have the following characteristics:
Qualified personnel are properly trained. Training as well as practical
knowledge and experience make up their qualifications. This is the
Installation BATOne
Release 01 01/2019
6

prerequisite for grounding and labeling circuits, devices, and systems
in accordance with current standards in safety technology.
Qualified personnel are aware of the dangers that exist in their work.
Qualified personnel are familiar with appropriate measures against
these hazards in order to reduce the risk for themselves and others.
Qualified personnel receive training on a regular basis.
Installation site requirements
Install this device in an operating site with restricted access, to which
maintenance staff have exclusive access.
Certified usage
Use the product only for the application cases described in the
Hirschmann product information, including this manual.
Operate the product only according to the technical specifications.
See Technical data on page 39.
Connect to the product only components suitable for the requirements
of the specific application case.
Requirements for connecting electrical wires
Before connecting the electrical wires, always verify that the requirements
listed are complied with.
All of the following requirements are complied with:
The electrical wires are voltage-free.
The cables used are permitted for the temperature range of the application case.
Table 1: General requirements for connecting electrical wires
Requirements for connecting data lines
Before connecting the electrical wires, always verify that the requirements
listed are complied with.
All of the following requirements are complied with:
The voltage connected complies with the requirements for a safety extra-low voltage
(Environment A - SELV) as per IEC/EN 60950-1.
Table 2: Requirements for connecting data lines
Installation BATOne
Release 01 01/2019 7

WARNING
ELECTRIC SHOCK
Use only Safety Extra Low Voltage circuit.
Failure to follow this instruction can result in death, serious injury,
or equipment damage.
Requirements for connecting the signal contact
Before connecting the signal contact, always verify that the requirements
listed are complied with.
All of the following requirements are complied with:
The voltage connected complies with the requirements for a safety extra-low voltage
(SELV) as per IEC/EN 60950-1.
The connected voltage is limited by a current limitation device or a fuse.
Observe the electrical threshold values for the signal contact.
See Technical data on page 39.
Table 3: Requirements for connecting the signal contact
Requirements for connecting the grounding
Before connecting the grounding, always verify that the requirements
listed are complied with.
Device variant
Requirements
All variants
The wire diameter of the ground conductor in the power supply
cable is the same size as or bigger than the wire diameter of the
power supply cables, however of at least 0.75
mm² (AWG18).
When connecting the provided cable lug, use a professional
crimping tool specified for the wire size. Follow the instructions
of the crimping tool. The pull out force of the crimped
connection is at least 135
N according to the technical standard
IEC 60352-2.
Table 4: Requirements for connecting the grounding
Requirements for connecting the supply voltage
Before connecting the supply voltage, always verify that the requirements
listed are complied with.
Installation BATOne
Release 01 01/2019
8

Device variant
Requirements
All variants
All of the following requirements are complied with:
The supply voltage corresponds to the voltage specified on the
type plate of the device.
The supply voltage conforms to overvoltage category I or II.
The supply voltage has an easily accessible disconnecting device
(e. g., a switch or a plug). This disconnecting device is clearly
identified. So in the case of an emergency, it is clear which
disconnecting device belongs to which power supply -cable.
A fuse is located in the outer conductor of the power supply.
The neutral conductor is on ground potential at both voltage
inputs. Otherwise, a fuse is also located in the neutral
conductor.
Regarding the properties of this fuse:
See Technical data on page 39.
The power supply cable is suitable for the voltage, the current
and the physical load. The wire diameter is at least
0.75 mm²(North America: AWG18).
Table 5: Requirements for connecting the supply voltage
WARNING
ELECTRIC SHOCK
Use only Safety Extra Low Voltage circuit.
Failure to follow this instruction can result in death, serious injury,
or equipment damage.
Supply voltage
The supply voltage is connected to the device casing through protective
elements exclusively.
Shielding ground
The overall shield of a connected shielded twisted-pair cable is
connected to the metal housing as a conductor.
Beware of possible short circuits when connecting a cable section
with conductive shielding braiding.
Grounding the device
Grounding the device is by means of a separate ground connection on the
device.
Ground the device before connecting any other cables.
Disconnect the grounding only after disconnecting all other cables.
Installation BATOne
Release 01 01/2019 9

Use toothed washers to ensure good electrical conductivity at the
connection.
Device casing
Only technicians authorized by the manufacturer are permitted to open
the housing.
Install the device in the vertical position, with the antenna connections
pointing upwards.
At ambient air temperatures > 140 °F (+60 °C):
The surfaces of the device housing may become hot. Avoid touching
the device while it is operating.
To preserve the suitability of your device for IP65/67, proceed as
follows:
Remove the provided transport protection caps and the transport
protection screws from the device.
Seal unused sockets and plugs with your desired type of protection
screws which you can order separately.
Lightning protection
Refer to the information in the “WLAN Outdoor Guide” on “Lightning
and overvoltage protection”.
You can download the manual from the Internet on the Hirschmann
product pages (http://www.hirschmann.com).
Install over voltage protector devices on every outdoor Ethernet cable.
Protect antennas installed outside with lightning protection devices (for
example lightning conductors).
Take lightning protection measures which mitigate the effects of
lightning strikes.
The installation of the device occurs in accordance with valid standards
(such as VDE 0185 and IEC 62305), and in accordance with the
lightning protection procedures recognized and proven for the
application and the environment.
National and international safety regulations
Verify that the electrical installation meets local or nationally applicable
safety regulations.
When installing antennas, observe the regulations of the country in
which you are operating the WLAN device with regard to the general
operating permission and the maximum emission levels.
Install and operate this equipment with a minimum distance of
19.7 inches (50 cm) between the antenna and your body.
Installation BATOne
Release 01 01/2019
10