Hirschmann PowerMICE MS4128 User manual

PowerMICE
Document No.: 039654005 Release 01 04/2014
Technical support
https://hirschmann-support.belden.eu.com
User Manual
Installation
Industrial Ethernet Switch
PowerMICE

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2014 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Document No.: 039654005 PowerMICE –4.4.14

PowerMICE
Release 01 04/2014 3
Contents
Safety instructions 5
About this Manual 13
Legend 13
1 Device description 14
1.1 Description of the modules 15
1.1.1 PowerMICE basic module MS4128 16
1.1.2 Media modules 18
1.1.3 MB-2T expansion module 22
1.1.4 SFP modules 23
2 Assembly and start-up 24
2.1 Overview of installation 24
2.2 Installing the device 25
2.2.1 Unpacking and checking 25
2.2.2 Installing the media modules 25
2.2.3 Filling out and attaching labels 25
2.2.4 Installing the SFP modules 26
2.2.5 Adjusting DIP switch settings on basic module 27
2.2.6 Adjusting the DIP switch settings on the
MM20-A8A89999SAHH media module 28
2.2.7 Connecting the MM22-T1T1T1T1 PoE media module 28
2.2.8 Connecting the terminal blocks for supply voltage and
signal contact 30
2.2.9 Installing the terminal blocks; start-up procedure 31
2.2.10 Installing the device on the DIN rail, grounding 31
2.2.11 Connecting the data lines 32
2.2.12 Installing the MB-2T expansion module 35
2.2.13 Defining the meaning of the display LEDs 36
2.3 Display elements 36
2.4 Basic set-up 40
2.5 Maintenance 42
2.6 Disassembly 43
3 Technical data 44
A Further Support 57

4PowerMICE
Release 01 04/2014

PowerMICE
Release 01 04/2014 5
Safety instructions
This documentation contains instructions which must be observed to ensure
your own personal safety and to avoid damage to devices and machinery.
Important Information
Notice: Read these instructions carefully, and look at the equipment to
become familiar with the device before trying to install, operate, or
maintain it. The following special messages may appear throughout this
documentation or on the equipment to warn of potential hazards or to call
attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety label
indicates that an electrical hazard exists, which will result in
personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
Note: A note contains important information on the product, on how to
manage the product, or on the respective section of the documentation to
which your special attention is being drawn.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
can result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.

6PowerMICE
Release 01 04/2014
Certified usage
The device may only be employed for the purposes described in the
catalog and technical description, and only in conjunction with external
devices and components recommended or
approved by the manufacturer. The product can only be operated cor-
rectly and safely if it is transported, stored, installed and assembled pro-
perly and correctly. Furthermore, it must be operated and serviced
carefully.
Supply voltage
For safety reasons the devices have been designed to operate at low
voltages. Thus, they may only be connected to the supply voltage
connections and to the signal contact with SELV circuits with the voltage
restrictions in accordance with IEC/EN 60950-1.
The supply voltage is electrically isolated from the housing.
Note: Only the PoE media module MM22-T1T1T1T1 has an external
power supply.
Use undamaged parts.
Relevant for North America:
The device may only be connected to a supply voltage of class 2 that
fulfills the requirements of the National Electrical Code, Table 11(b). If
the voltage is being supplied redundantly (two different voltage
sources), the combined supply voltages must fulfill the requirements of
the National Electrical Code, Table 11(b).
Relevant for North America: For use in Class 2 circuits.
Only use copper wire/conductors of class 1, 75 °C (167 °F).
For using the device in areas with a risk of gas explosion according to
directive 94/9/EC (ATEX):
Make sure that the device carries the following device label:
II 3G (... followed by additional specifications).
Observe the clause "Special Conditions for Safe Use ..." on the
following pages.

PowerMICE
Release 01 04/2014 7
Relay
P2
P1
Relay
Ordinary Location,
Non-Hazardous Area,
Non-Explosive Atmosphere
WARNING!
The USB connection and the V.24 Interface connection are for
temporary connection only, for maintenance use. Do not use,
connect or disconnect unless the area is known to be non-hazar- dous. Connection or disconnection in an explosive atmosphere could result in an explosion!
Power Supply range P1, P2 (redundant)
18 – 32 VDC
4.5 – 2.5 A
Relay contacts:
The relays are “Sealed Devices”.
THE RELAY TERMINALS ARE DEPENDENT UPON THE
FOLLOWING PARAMETERS - max. values:
Uin Iin
30 V 90 mA
Zone 2, IIC
Explosive Atmosphere
The earth conductor must be at least the
same wire size (mm² or AWG) as the supply
conductors.
Page 1/2 Special Conditions for Safe Use under Directive 94/9/EC, ATEX Applied Standards: EN 60079-0: 2009, EN 60079-15: 2010
z-section sheet

8PowerMICE
Release 01 04/2014
Ambient temperature range “Ta: 0°C … + 60°C” ; Temperature Code “T4”. The modules shall be installed in a suitable IP54 enclosure - with tool removable cover - in accordance with EN 60079-15, taking into account the environmental conditions under which the equipment will be used. The power supply plugs P1 and P2 have to be secured by the supplied z-section sheet and M2.5 screw inclusive tooth washer. Provisions shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than 119 V. When the temperature under rated conditions exceeds 70 °C at the cable or conduit entry point, or 80 °C at the branching point of the conductors, the temperature specification of the selected cable shall be in compliance with the actual measured temperature values. DO NOT OPEN WHEN ENERGIZED. Manufactured in 72654 Neckartenzlingen, Germany, by Hirschmann Automation and Control GmbH DOM: ww/yyyy (Date Of Manufacture: w - week, y - year – Refer to the device label.) The Use in Hazardous Locations with explosive atmospheres is only allowed for MS4128-xxx or HS600x model no´s. which are individually labelled
“ II 3G” and “Ex nA IIC T4 Gc”
Page 2/2 Special Conditions for Safe Use under Directive 94/9/EC, ATEX

PowerMICE
Release 01 04/2014 9
Shielded ground
The shielded ground wire of the twisted pairs lines is connected to the
front panel as a conductor.
Beware of possible short circuits when connecting a cable section with
conductive shield braiding.
Housing
Only technicians authorized by the manufacturer are permitted to open
the housing.
WARNING
ELECTRIC SHOCK
Never insert any pointed objects (small screwdrivers, wires, etc.) into the
product!
Never insert sharp objects (small screwdrivers, wires, etc.) into the
connection terminals for the supply voltage or the signal contact, and do not
touch the terminals!
Failure to follow these instructions can result in death, serious injury,
or equipment damage.
CAUTION
EQUIPMENT OVERHEATING
When installing the device, make sure any ventilation slots remain free.
Maintain a clearance of at least 10 cm (3.94 in).
Failure to follow these instructions can result in injury or equipment
damage.

10 PowerMICE
Release 01 04/2014
The lower panel of the device is grounded by means of the DIN rail and
optionally by means of the separate ground screw.
The switch basic module forms an inseparable unity. By removing the
display and connecting parts, you risk the damage of the switch basic
module.
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
The ventilation slots must not be covered to promote free air
circulation.
The clearance between the ventilation slots of the housing and other
objects must be at least 10 cm (3.94 in).
The device has to be mounted in an upright position (see fig. 13).
If installed in a living area or office environment, the device must be
operated exclusively in switch cabinets with fire protection
characteristics in accordance with EN 60950-1.
Environment
The device may only be operated at the specified surrounding air
temperature (temperature of the surrounding air at a distance of up to
5 cm (1.97 in) from the device) and relative air humidity specified in the
technical data.
Install the device in a location where the climatic threshold values
specified in the technical data will be observed.
Use the device only in an environment within the pollution degree
specified in the technical data.
Qualification requirements for personnel
Qualified personnel as understood in this manual and the warning signs,
are persons who are familiar with the setup, assembly, startup, and
operation of this product and are appropriately qualified for their job. This
includes, for example, those persons who have been:
trained or directed or authorized to switch on and off, to ground and to
label power circuits and devices or systems in accordance with current
safety engineering standards;
trained or directed in the care and use of appropriate safety equipment
in accordance with the current standards of safety engineering;
trained in providing first aid.
General safety instructions
Electricity is used to operate this equipment. Comply with every detail of
the safety requirements specified in the operating instructions regarding
the voltages to apply.
See “Supply voltage” on page 6.

PowerMICE
Release 01 04/2014 11
Non-observance of these safety instructions can therefore cause material
damage and/or injuries.
Only appropriately qualified personnel should work on this device or in
its vicinity. Qualified personnel must be thoroughly familiar with the
warnings and maintenance procedures in accordance with this
operating manual.
The proper and safe operation of this device depends on proper
handling during transport, proper storage and assembly, and
conscientious operation and maintenance procedures.
Never start operating the device with damaged components.
Only use the devices in accordance with this manual. In particular,
observe the warnings and safety-related information.
Any work that may be required on the electrical installation may only
be carried out by personnel trained for this purpose.
Note: LED or LASER components in compliance with IEC 60825-1
(2007):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT
Note: Follow the safety instructions for the media modules. You will find
these instructions in the “Description and Operating Instructions”
document supplied with the media module.
National and international safety regulations
Make sure that the electrical installation meets local or nationally
applicable safety regulations.
CE marking
The labeled devices comply with the regulations contained in the following
European directive(s):
2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.
2004/108/EC (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.
In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:

12 PowerMICE
Release 01 04/2014
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Tel.: [phone]
The product can be used in the industrial sector.
Interference immunity: EN 61000-6-2:2005
Emitted interference: EN 55022:2010
Warning! This is a class A device. This device can cause interference in
living areas, and in this case the operator may be required to take
appropriate measures.
Note: The assembly guidelines provided in these instructions must be
strictly adhered to in order to observe the EMC threshold values.
FCC note
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions : (1) This device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate high
frequencies, and if it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a living area can also cause interference, and in this case
the user is obliged to cover the costs of removing the interference.
Recycling note
After usage, this product must be disposed of properly as electronic
waste, in accordance with the current disposal regulations of your county,
state and country.

PowerMICE
Release 01 04/2014 13
About this Manual
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The following manuals are available as PDF files on the CD-ROM supplied:
Installation user manual
Basic Configuration user manual
Redundancy Configuration user manual
Router Configuration user manual
Graphical User Interface reference manual
Command Line Interface user manual
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
Simultaneous configuration of multiple devices
Graphic interface with network layout
Auto-topology discovery
Event log
Event handling
Client/server structure
Browser interface
ActiveX control for SCADA integration
SNMP/OPC gateway.
Legend
The symbols used in this manual have the following meanings:
Listing
Work step
Subheading

14 PowerMICE
Release 01 04/2014
1 Device description
The PowerMICE devices consist of a switch with media modules that can be
plugged into it. The devices have 4 slots for 10/100 Mbit/s media modules
and 1 slot for 1 Gigabit module. The slot for the Gigabit module supports 2
Gigabit ports. The expansion module provides you with 2 additional slots for
10/100 Mbit/s media modules. Each media module provides you with 2 to 4
ports for connecting network segments.
The PowerMICE devices are designed for the special requirements of
industrial automation. They meet the relevant industry standards, provide
very high operational reliability, even under extreme conditions, and also
provide long-term reliability and flexibility.
The devices work without a fan.
The voltage is supplied redundantly.
The following installation options are available:
simply snapping them onto a DIN rail
You can choose various media to connect terminal devices and other
infrastructure components:
twisted pair cable
multimode F/O
singlemode F/O
The twisted pair ports support:
Autocrossing
Autonegotiation
Autopolarity
The following software variants are available:
MICE MS4128-L2P: Layer 2 Professional
MICE MS4128-L3E: Layer 3 Enhanced
MICE MS4128-L3P: Layer 3 Professional
There are convenient options for managing the device. Administer your
devices via:
a Web browser
Telnet
management software (e.g. Industrial HiVision)
a V.24 interface (locally on the device)
The ring redundancy concept allows the network to be reconfigured quickly
after a failure.

PowerMICE
Release 01 04/2014 15
Product configuration data can be provided by:
diagnosis displays
displaying the operating parameters
large label areas
The clear division of the diagnosis displays and the connection level allows
you to view the LEDs easily.
The devices provide you with a large range of functions. Information
pertaining to these functions is found in the relevant operating software
manuals. These manuals are available as PDF files on the CD ROM
provided, or you can download them from the Internet on the Hirschmann
product pages (www.hirschmann.com).
The Hirschmann network components help you ensure continuous
communication across all levels of the company network.
Figure 1: Basic module with media modules attached
1 – Slots for one 10/100 Mbit/s media module
2 – Basic module
3 – Slot for the Gigabit media module
1.1 Description of the modules
The industrial ETHERNET series PowerMICE (Modular Industrial
Communication Equipment) consists of a basic switch module and the media
modules. These devices can be managed. A basic module contains all the
functions of this industrial Switch, with the exception of the interfaces to the
LAN that is connected. Pluggable media modules provide these interfaces.
They differ with regard to the number of interfaces and the media type for
connecting segments. An expansion module enables you to add 2 slots for
media modules to the basic module.
For the sake of simplicity, the basic switch module with various plugged in
media modules will be referred to as PowerMICE in this document.
321111

16 PowerMICE
Release 01 04/2014
1.1.1 PowerMICE basic module MS4128
The basic module of the PowerMICE contains all the function units, such as:
switch function, management function, redundancy function, display control,
voltage connection, management connection, adjustable controls, slots for
media modules.
The basic module provides:
4 slots for 10/100 Mbit/s media modules
1 slot for 1 Gbit/s media modules
With the expansion module you add 2 more slots for 10/100 Mbit/s media
modules. With its 4-port media modules, the basic module allows you to
connect up to:
16 network segments or
24 network segments when using an expansion module
and additionally
4 Gigabit network segments when using a 4-port Gigabit media module.
Family Designed for:
PowerMICE larger numbers of ports
larger bandwidth requirement
Selectable via media modules:
Number of 100/1000 Mbit/s ports

PowerMICE
Release 01 04/2014 17
Figure 2: Front of the basic module
1 – Slot for SFP module MM4...
2 – Basic module
3 – Slot for media modules MM2… or MM3… with 2 to 4 ports each
4 – Ground screw
5 – Connections on the bottom of the basic module
6 – Button for setting the display status
7 – LEDs for device status and display status
Figure 3: Basic module with expansion module
1 – Expansion module MB-2T
2 – Basic module
12
4
6
7
5
33 33
21

18 PowerMICE
Release 01 04/2014
Figure 4: Connections on the bottom of the basic module
1 – Terminal block (Power 2)
2 – DIP switch
3 – Terminal block (Power 1)
4 – USB port
5 – V.24 port
1.1.2 Media modules
The media modules form the interface from the device to the LAN.
The media modules can be used in the basic module.
An expansion module enables you to add 2 slots for media modules to the
basic module.
They differ with regard to the number of interfaces and the media type. The
different interfaces of the media modules provide you with the following
interface-specific functions:
Specific functions of TP/TX interface
Link Control
Auto Polarity Exchange
Autonegotiation
Autocrossing (device may be connected with a crossed-over or an un-
crossed cable)
Specific functions of F/O interface
Link Down monitoring
Transceiver-specific (AUI-specific) functions
Collision recognition
Collision test (SQE)
Protection from permanent network connection (Jabber Control)
DTE Power Monitor
1
2
3
4
5

PowerMICE
Release 01 04/2014 19
Depending on the basic module setting, the LEDs display, among other
things, the data reception and the connection status.
MM2 media modules
Figure 5: Port assignment
1 - Port 1
2 - Port 2
3 - Port 3
4 - Port 4
5 - Illustration of the port numbers
6 - Bottom side of the device
MM2 media modules
Module type
TP ports 10/
100 Mbit/s
F/O port
multi-mode
10 Mbit/s
F/O port
multi-mode
100 Mbit/s
F/O port
single-
mode 1300
nm, 100
Mbit/s
F/O port
single-
mode 1550
nm, 100
Mbit/s
MM2-4TX1(-EEC)4,RJ45––––
MM2 - 2FLM4 – 2, ST – – –
MM2-4FXM3––4,MTRJ––
MM2 - 2FXM3 / 2TX1 2, RJ45 – 2, MTRJ – –
MM2 - 2FXM2 – – 2, DSC – –
MM2-2FXS2–––2,DSC–
Table 1: Media connections per MM2 media modules (number and type)
2
5
6
4
1
3
6

20 PowerMICE
Release 01 04/2014
MM3 media modules
Figure 6: Port assignment
1 - Port 1
2 - Port 2
3 - Port 3
4 - Port 4
5 - Illustration of the port numbers
6 - Bottom side of the device
MM3 media modules
Module type
TP ports 10/
100 Mbit/s
F/O port
multi-mode
10 Mbit/s
F/O port
multi-mode
100 Mbit/s
F/O port
single-
mode 1300
nm, 100
Mbit/s
F/O port
single-
mode 1550
nm, 100
Mbit/s
MM3-4TX5 4, M12 – – – –
MM3-4FLM4 – 4, ST – – –
MM3-1FXM2/3TX1 3, RJ45 – 1, DSC – –
MM3-2FXM2/2TX1(-EEC) 2, RJ45 – 2, DSC – –
MM3-2FXM4/2TX1 2, RJ45 – 2, ST – –
MM3-4FXM2 – – 4, DSC – –
MM3-4FXM4 – – 4, ST – –
MM3-1FXS2/3TX1(-EEC) 3, RJ45 – – 1, DSC –
MM3-2FXS2/2TX1 2, RJ45 – – 2, DSC –
MM3-4FXS2 –––4,DSC–
MM3-1FXL2/3TX1 3, RJ45 – – – 1, DSC
Table 2: Media connections per MM3 media modules (number and type)
2
5
6
4
1
3
6