Hisense AVS-07UR2SABA Instruction Manual

P008424
ORIGINAL INSTRUCTIONS
Wall-
Mounted
Type
AVS-07UR2SABA ；
AVS-09UR2SABA ；
AVS-12UR2SABA ；
AVS-14UR2SABA ；
AVS-17UR2SABA ；
AVS-07UR2SABB
AVS-09UR2SABB
AVS-12UR2SABB
AVS-14UR2SABB
AVS-17UR2SABB

32DB/23WB
HISENSE
HISENSE
HISENSE

HISENSE's
HISENSE's
IMPORTANT NOTICE
Correct Disposal of this product
This marking indicates that this product should not be disposed with other
household wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.

Identification Of Parts









1
1
1
1
Section2 Installation & Maintenance Manual
Remote Control Switch
Setting of Swing /RXYHU
Filter Cleaning
Taking Out the Filter
Cleaning the Filter
Reset of Filter Indication








1
1






6LJQDO5HFHSWRU



1
1
1
1
1
1
1
Common

the Filter Indication Interval
,QGRRU8QLW$GGUHVV 




1409
07 12
Wall-Mounted Type
O
O
O
The appliance is not to be used by children
or person with reduced physical,sensory or
Children should be supervised that they
do not play with the appliance.
The appliance should not be installed in the
laundry.
(×10 Btu/h)
3
mental capabilities,or lack of experience
and knowledge, unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
17
OIf the supply cord is damaged, it must be
replaced by the manufacturer,its service
agent or similarly qualified persons in
order to avoid a hazard.

Air Intake
Air Outlet
Vertical Adjustment
Louver
Front Panel
Display Panel
Horizontal Adjustment
Louver
Air Filter
Remote Controller
,GHQWLILFDWLRQRI3DUWV
)LJ([WHUQDO3DUWVRI6\VWHP


Press switches only with fingers.
Do not press switches by any other
item,as it may break switches.
)LJExample RI5HPRWH&RQWUROOHU
Regarding the instructions of Wired Remote
Control Switch or Wireless Remote Control
Switch,read the operation manual attached to
the control switch.
The pictures of Control Switch are only example.
The matter is related to the optional parts of
customer choices.

" " DQG " "
VLPXOWDQHRXVO\
WZR
RQO\
WZR
7KHVH
2014- 08 - 18 Fri
If use the Wired Remote Control Switch，the
connecting wire of siginal receptor should be
removed , if not , the receiver display alarm code.

6
2
53
1
 6LJQDO5HFHSWRU
'LVSOD\LQWURGXFWLRQ
)LJ6LJQDO5HFHS
WRU

3
2
5
1
6
Temperature control indicator
It lights up when temperature deviate the set temperature.
......................................................... 4
Display set temperature.
It shows FC after 200 hours of usage as reminder to clean the filter.
After filter cleaning press the filter reset button located on the indoor
unit behind the frontpanel in order to reset the display.
Temperature indicator 
Sleep indicator
It lights up in sleep mode.

Running indicator
It lights up when the AC is running.
It flashes during defrosting.

Timer indicator
It lights up during set time.
Signal Receptor


12
2
53
4
6
BA series
BB series
To operate the room air conditioner, aim the remote controller to the signal receptor.
The remote controller will operate the air conditioner at a distance of up to 7m when
pointing at signal receptor of indoor unit.
Signal display lights for 10 seconds, when operate the wireless remote control switch.
Fig.4.1 Signal Receptor




7
8.

8.1

9
9.1
9.2
9.3
9.4

8.2
8.3
approximately
d
³),/7(55(6(7´


2. Necessary Tools
and Instrument List for Installation
equipments for R410A
Users can not change power
lines by themselves, replaced
by professional maintenance
staffs.
irrelevant

Accessory Quantity Purpose
Mounting
Bracket
Screw
Crew Cover
For Mounting Indoor Unit
For Mounting Bracket
For Crew of Air Outlet
1000
Fig. 4.1 Operation and Maintenance Space Fig. 4.2 Hole for Piping on the Wall

For Refrigerant Pipe
Thermal
Insulation Pipe

3
1
1
¶h/
:DOO
2 to 5mm
Diameter of 65mm
Hole for Piping
,1'225
81,7
2.3
100
150
100
(unit:mm)
wall and
board
hanging
1
:LUHOHVV5HPRWH
&RQWURO6ZLWFK For&RQWUROWKH,QGRRU8QLW
For Mounting Bracket
([SDQVLRQ
%ROWV


Fig.4.3 Mounting Bracket
(unit:mm)
Capacity(.%XWK):///
4.3 Installation
The dimensions of the mounting bracket and the
unit installation are indicated in Fig. 4.3.
4.3.1 Mounting Bracket onto Wall
When the mounting bracket is directly attached
to a wood wall or a concrete wall, check to ensure
of 2000N.
Attach the mounting bracket to the concrete wall
with anchor bolts as shown in Fig. 4.4
Fig. 4.4 Mounting on Concrete Wall
Screw
Mounting Bracket

One Each Side

Hook
Mounting
Bracket
HookExtrusion
4.3.2 Mounting the Indoor Units
Hook the indoor unit to the mounting bracket,
maintaining the indoor unit upright.
Fig 4.5 Mounting of the Indoor Units
Check to ensure that the unit is
completely hooked onto the mounting
bracket.If not,it may drop from the bracket,
resulting in a serious accident.
4.3.3 Removing Front Panel
In order to connect the refrigerant piping,
wiring and to check drain water flow, removing
the front panel is needed. Perform these work
according to the following instructions. Pay
attention to the resin components not to scratch.
(1) Hold both sides of the flat panel and open it,
and pull the right arm toward the inner side.
Slightly close the flat panel and pull it, then
remove the flat panel.
Flat Panel
(2) Remove the air filter and VL[ () screws.
release the catch by paying attention to the air
outlet part without touching the outlet grille.
(3) Pay attention to the junction of grille
from each side, to prevent breaking off.
Fig 4. 6ORSDQJOHRI the Indoor Units
2QRQHVLGHRIWKHGUDLQSLSHLV
GRZQZDUGVORSLQJGHJUHHVRUGHJUHHV
LQWKHSURFHVVRIWKHXQLWLQVWDOODWLRQ
&KHFNWKHGUDLQDJHRIWKHGUDLQSDQ
WKURXJKZDWHURYHUIORZWHVW
'UDLQ3LSLQJ
Slowly pull the lower side of the front panel and

Flat Panel
Unit Body
Any gap will lead to leak or frost.
unit:mm(in.)
/LTXLGSLSH
*DVSLSH
PRGHO.%WXK

1
Stoppers
(4) Slightly lift the front panel upward in order
to release the combined parts of upper side of the
front pane
(3) There are IRXU stoppers inside of the flat
panel.Check to ensure that there is no gap
between flat panel and unit body.
4.3.4 Install Front Panel
(1) Firstly, put the four joints of the front panel back
into the grid, and then push inside to make the one
tightly fasten, finally, install six crews for the front
panel and three crew covers for air outlet crews.
(2) Press flat panel down , make the two joints of the
front panel tightly fasten.
5.1 Piping Materials
(1) Prepare locally-supplied copper pipes.
(2) Select the piping size from the following table.
(3) Select clean copper pipes making sure there
is no dust and moisture inside the tubes. Before
connecting pipes,blow the inside of the pipes with
nitrogen or dry air,to remove any dust or foreign
materials.
When removing flat panel, do not
apply strong forces by hitting, etc. It
may break the unit body.
R410A

When bending the pipes, firmly fix the pipe at
the heat exchanger side.
Insulation
For Left Side
Piping For Right Side Piping
Contour of the Unit
Fig. 5.1 Liquid pipe
Bend the gas pipe at the flexible pipe part.
Insulation
Fig. 5.2 Gas pipe
1
Contour of the Unit
For Right side Piping
For Left Side Piping
07/09/12/14/17
DEF
For Rear Side Piping
For Rear Side
Piping
Model(KBtu/h)
Small Cover
Right Side Cover
Left Side Cover
  3
(unit:mm)
(1) Position of piping connection is shown in
Figure 5.1 and 5.2.
(2) Piping Direction for the Indoor Unit Three
directions of piping connection to the indoor
unit can be performed; to the rear side, the right
side and the left side of the unit, respectively.
Therefore, most appropriate piping for a room can
be selected.
5.2 Piping Connection
Right Side Piping
Take off the small cover from right side.
Left Side Piping
Take off the small cover from left side.
Rear Side Piping
Bend pipe backwards directly.
DEF
8 3
(unit:mm)
Model(KBtu/h)
07/09/12/14/17
5
5

Pipe diameter Torque (N m)
Fig.5.3 Tightening Work of Flare Nut
Thermal Insulation pipe
on-site configuration
Fig. 5.4 Insulation on pipes
6. Drain Piping
Fig. 6.1 07~17 Direction of Drain Piping
1
Fig. 5.6
20
60
¶
¶
Unit Spacer
Approx.150mm
Stopper
Plate for Pipe
.
(3) When tightening the flare nut, use two
spanners as shown in Fig. 5.3
(4) Insulate the refrigerant pipes as shown in
Fig. 5.4.
(5) Evacuation and refrigerant charging procedures
should be performed according to “Installation &
Maintenance Manual ” of the outdoor unit.
(6) When connecting the pipes, use the unit
spacer (factory-supplied) as shown in Fig. 5.5.
Fig. 5.5 Using the Unit Spacer
(7) Fix the plate of pipes (factory-supplied) as
shown in Fig. 5.6.
(2) For 07~17, when the left side drain piping
connection is performed, remove the cap of left side
drain pipe, and then attach this cap to the right side
drain pipe in order to change drain piping connection
from right side to left side.
An excess or a shortage of
main cause of
Charge the
refrigerant is the
correct refrigerant quantity.
trouble to the units.
168
45
560
Contour of the Unit
Drain Pipe
Connection
for Vinyl Pipe
(VP16)
65 Hole for
Rear Side Connection for
Wiring and Piping
(1) The standard direction of drain piping connection is
right side as viewed from the discharge grilles.
However, it can be performed from the left side or rear
side.
Must attach the cap to the left side drain pipe,
when the left side drain piping connection is
performed.
Change Drain Piping Connection
Fig. 6.2 Left Side Connect

Provide a downward slope to
flow drain water smoothly
Use Adhesive Tape
Fig. 6.3 Connection of Drain Piping
1
(3) Provide a vinyl chloride pipe, VP20.
(4) Connect a drain piping as shown in Fig. 6.3.
Use adhesive tape for connecting the drain pipe.
(5) Pour water into the drain pan and check to
ensure that water can flow smoothly.
Do notconnect thedrain pipeswith
sanitary or sewage or any other
When installing the pipe, do not tie the
drain pipe andrefrigerant pipetogether.
Pay attention to the thickness of the
insulation when the left side piping is
too thick, piping
drainage pipe.
performed. If it is
cannot beinstalled inthe unit.
OTighten screws according to the
following torque.
M3.5: 1.2 N m
M5: 2.0 to 2.4 N m
.
.