Hisense RF702N4 I S1 Mounting instructions

RF702N4 I S11
RF702N4 I S1
RF715N4AS1
FMN544I20SFMN544I20S

2
Contents
Safety and warning information2
Installing your new appliance 8
Description of the appliance14
Display controls16
Using your appliance 18
Cleaning and care2
Helpful hints and tips21
Troubleshooting22
Disposal of the appliance24
Safety and warning information
For your safety and correct usage, before installing and first
using the appliance, read this user manual carefully, including
its hints and warnings. To avoid unnecessary mistakes and
accidents, it is important to make sure that all people using the
appliance are thoroughly familiar with its operation and safety
features. Save these instructions and be sure that they remain
with the appliance if it is moved or sold, so that anyone using it
throughout its life, will be properly informed on its usage and
safety notices.
For the safety of life and property, keep the precautions of
these user's instructions as the manufacturer is not
responsible for damages caused by omission.
Safety for children and others who are ulnerable people
According to EN standard
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
According to IEC standard
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.

3
Keep all packaging away from children as there is risk of
suffocation.
If you are discarding the appliance, pull the plug out of the
socket, cut the connection cable (as close to the appliance as
you can) and remove the door to prevent children playing
from suffering an electric shock or from closing themselves
inside it.
If this appliance, featuring a magnetic door seals, is to replace
an older appliance having a spring lock (latch) on the door or
lid, be sure to make the spring lock unusable before you
discard the old appliance. This will prevent it from becoming a
death trap for a child.
General safety
WARNING —This appliance is intended to be used in
household and similar applications such as
-staff kitchen areas in shops, offices and other working
environments;
-farm houses and by clients in hotels, motels and other
residential type environments;
-bed and breakfast type environments;
-catering and similar non-retail applications.
WARNING —Connect to potable water supply only.
WARNING — Do not store explosive substances such as
aerosol cans with a flammable propellant in this appliance.
WARNING — If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
WARNING — Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of obstruction.
WARNING — Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
WARNING — Do not damage the refrigerant circuit.
WARNING — Do not use electrical appliances inside the food
storage compartments of the appliance, unless they are of the

Caution:
4
type recommended by the manufacturer.
WARNING — The refrigerant and insulation blowing gas are
flammable. When disposing of the appliance, do so only at an
authorized waste disposal centre. Do not expose to flame.
WARNING —When positioning the appliance, ensure the
supply cord is not trapped or damaged.
WARNING —Do not locate multiple portable socket-outlets
Replacing the LED
WARNING—The LED light must not be replaced by the user!
If the LED light is damaged, contact the customer helpline for
assistance.
Refrigerant
The refrigerant isobutene (R6 a) is contained within the
refrigerant circuit of the appliance, a natural gas with a high
level of environmental compatibility, which is nevertheless
flammable. During transportation and installation of the
appliance, ensure that none of the components of the
refrigerant circuit becomes damaged.
The refrigerant (R6 a) is flammable.
WARNING — Refrigerators contain refrigerant and gases in
the insulation. Refrigerant and gases must be disposed of
professionally as they may cause eye injuries or ignition.
Ensure that tubing of the refrigerant circuit is not damage prior
to proper disposal.
If the refrigerant circuit should be damaged:
-Avoid opening flames and sources of ignition.
-Thoroughly ventilate the room in which the appliance is
situated.
Risk of fire / flammable materials

5
It is dangerous to alter the specifications or modify this product
in any way.
Any damage to the cord may cause a shortcircuit, fire, and/or
electric shock.
Electrical safety
1. The power cord must not be lengthened.
2. Make sure that the power plug is not crushed or damaged. A
crushed or damaged power plug may overheat and cause a
fire.
3. Make sure that you can access the main plug of the
appliance.
4. Do not pull the main cable.
5. If the power plug socket is loose, do not insert the power
plug. There is a risk of electric shock or fire.
6. You must not operate the appliance without the interior
lighting lamp cover.
7. The fridge is only applied with power supply of single phase
alternating current of 22 ~24 V/5 Hz. If fluctuation of voltage
in the district of user is so large that the voltage exceeds the
above scope, for safety sake, be sure to apply A.C. Automatic
voltage regulator of more than 35 W to the fridge. The fridge
must employ a special power socket instead of common one
with other electric appliances. Its plug must match the socket
with ground wire.
Daily use
Do not store flammable gass or liquids in the appliance.
There is a risk of an explosion.
Do not operate any electrical appliances in the appliance
(e.g.electric ice cream makers, mixers etc.).
When unplugging always pull the plug from the mains socket,
do not pull on the cable.
Do not place hot items near the plastic components of this
appliance.

6
Do not place food products directly against the air outlet on
the rear wall.
Store pre-packed frozen food in accordance with the frozen
food manufacture’s instructions.
The appliances manufactures storage recommendations
should be strictly adhered to. Refer to relrelevant instructions
for storage.
Do not place carbonated or fizzy drinks in the freeze
compartment as it creates pressure on the container, which
may cause it to explode, resulting in damage to the appliance.
Frozen food can cause frost burns if consumed straight from
the freezer compartment.
Do not place the appliance in direct sunlight.
Keep buring candles, lamps and other items with naked
flames away from the appliance so that do not set the
appliance on fire.
The appliance is intended for keeping food stuff and/or
beverages in normal household as explained in this
instruction booklet The appliance is heavy. Care should be
taken when moving it.
Do not remove nor touch items from the freezer compartment
if your hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Never use the base, drawers, doors etc. to stand on or as
supports.
Frozen food must not be refrozen once it has been thawed
out.
Do not consume ice popsicles or ice cubes straight from the
freezer as this can cause freezer burn to the mouth
and lips.
To avoid items falling and causing injury or damage to the
appliance, do not overload the door racks or put too much
food in the crisper drawers.
caution!
Care and cleaning

7
Before maintenance, switch off the appliance and disconnect
the mains plug from the mains socket.
Do not clean the appliance with metal objects, steam cleaner,
ethereal oils, organic solvents or abrasive cleansers.
Do not use sharp objects to remove frost from the appliance.
Use a plastic scraper.
Installation Important!
For electrical connection carefully, follow the instructions
given in this manual.
Unpack the appliance and check if there are damages on it.
Do not connect the appliance if it is damaged. Report possible
damages immediately to the place you bought it. In this case
retain packing.
It is advisable to wait at least four hours before connecting the
appliance to allow the oil to flow back in the compressor.
Adequate air circulation should be around the appliance,
lacking this leads to overheating. To achieve sufficient
ventilation, follow the instructions relevant to installation.
Wherever possible the back of the product should not be too
close to a wall to avoid touching or catching warm parts
(compressor, condenser) to prevent the risk of a fire, follow
the instructions relevant to installation.
The appliance must not be located close to radiators or
cookers.
Make sure that the mains plug is accessible after the
installation of the appliance.
Ser ice
Any electrical work required to do the servicing of the
appliance should be carried out by qualified electrician or
competent person.
This product must be serviced by an authorized Service
Center, and only genuine spare parts must be used.
1) If the appliance is Frost Free.
2) If the appliance contains freezer compartment
Note: Children aged from 3 to 8 years are allowed to load and
unload refrigerating appliances.(This clause applies only to the
EU region.)

8
Installing your new appliance
Before using the appliance for the first
time, you should be informed of the
following tips.
Warning!
For proper installation, this refrigerator
must be placed on a level surface of hard
material that is the same height as the rest
of the flooring. This surface should be
strong enough to support a fully loaded
refrigerator.
The rollers, which are not castors, should
be only used for forward or backward
movement. Moving the refrigerator
sideways may damage your floor and the
rollers.
Ventilation of appliance
Install the appliance in a plane
and stable surface. Assure
good ventilation.
We recommend letting a space at least:
- 5 -7 mm from the back to the wall
- 1 mm from the top to the wall
- 1 mm from its side to the wall
Enough space must be provided in the
front of the appliance to allow the doors to
open as shown in follow diagrams.
Note:
 This appliance performs well within the
climate class from SN to T showed in the
table below. It may not work properly if
being left at a temperature above or below
the indicated range for a long period.
Climate class Ambient temperature
SN +1 °C to +32°C
N +16°C to +32°C
ST +16°C to +38°C
T +16°C to +43°C
 Stand your appliance in a dry place to
avoid high moisture.
 Keep the appliance out of direct sunlight,
rain or frost. Stand the appliance away
from heat sources such as stoves, fires or
heaters.
Le eling of appliance
For sufficient leveling and air circulating
in the lower rear section of the appliance,

9
the bottom feet may need to be adjusted.
You can adjust them manually by hand or
by using a suitable spanner.
To allow the doors to self-close, tilt the
top backwards by 1 -15 mm.
Whenever you want to move the
appliance, remember to turn the feet back
up, so that the appliance can roll freely.
Reinstall the appliance when relocating.
Doors remo al
In case when your access door is too
narrow for the refrigerator to pass through,
remove the refrigerator door and drawers.
Then pass the refrigerator laterally. If you
do not need to remove the appliance
doors, go to ‘Installing the water lines’ on
page 11.If you need to remove the doors,
continue below.
Warning!
When reversing the door, the appliance
must be unplugged.
The tools you will need (Not pro ided):
Allen Wrench(4mm)
Wrench(8mm)
Philips screwdriver
Disassembling the fridge door
Some models may be slightly different
from pictures. If some parts shown in the
picture cannot found in your appliance,
please ignore the relevant description.
1. With the door closed, remove the 3
screws holding the top cover (A) with
Philips (+) screwdriver, and then remove
the top cover carefully with the
entire-harnesses unattached.
2.Take out connectors and the water
coupler from the installation clip.
Remove the two wire connectors (press
the top of the connector (B) and separate
it from the other one) on the left side
door .To remove the water coupler from
the hinge, twist and pull the clips from the
coupler then remove the water line (C)
while pressing the movable part (D) of the
water line coupler.

1
3. Remove the 3 screws (B) fixed on the
hinges with a Wrench (8mm) and 1 ground
screws (C) attached to the hinge with
Philips (+) screwdriver. Remove the upper
left and right door hinges (D).
4. Use your both hands to open the door
more than 9 ° . Lift it up and take it off.
（ Be careful of racks while remove the
door. ）
5. Remove the 4 hex head bolts (E) with
an Allen wrench (4 mm). Remove the 2
screws with screwdriver. Then remove the
lower left and right door hinges (F).
Re-attaching the fridge doors
To reattach the fridge doors after you have
moved the appliance to its final location,
assemble the parts in reverse order.
1. To prevent water leaks, the water line
should be fully inserted into the center of
the coupler until the guide lines are
coincided exactly with the head of the
movable part.
Note ：
：：
：
Arrow on the water line coupler point to
the direction of the door.
2. Make sure the clips are properly
connected to the coupler.
Caution!
In case the fridge doors can’t be
self-closed, please make sure the door
opened more than 9 ° when you remove
or re-attaching the fridge doors.
Disassembling the freezer door
1. Pull out the freezer door and the upper
freezer drawer (A) to the final position.
Then take out the ice box (B) by lifting it up
in the direction of the arrow.

11
2. Take out the upper
freezer
by lifting it up
from the rail system.
3. Remove the lower
freezer
lifting it up.
4. Remove the 4
screws attached to the
supporting frame (D).
freezer
drawer (A)
from the rail system.
freezer
drawer (C) by
screws attached to the
5. Pull out the freezer
door and lift it up
the direction of the arrow.
Re-
assembling the freezer door
To reattach the drawer after you moved
the appliance to its final
assembling
the parts in reverse order.
(Optional)
Installing the water lines and filter
Installing the water filter
To fit the water filter, follow the installing
steps below.
1. T
ake out the water filter and water lines
from the fridge room.
2. D
etermine the location to mount the
external filter. (Note: The water filter
should be mount on the wall where it is
convenient to be replaced, and do not
mount on the wall behind the refri
3. D
etermine the distance between the
filter and the tap, and the distance from
the filter to the fridge. Prepare lines as
required lengths. (Cut the proper lengths
of water lines which you determine to
connect with the filter inlet or outlet.)
4. M
ount the filter holder onto the wall by
using a screwdriver and attach the water
filter.
door and lift it up
in
assembling the freezer door
To reattach the drawer after you moved
the appliance to its final
location,
the parts in reverse order.
Installing the water lines and filter
Installing the water filter
To fit the water filter, follow the installing
ake out the water filter and water lines
etermine the location to mount the
external filter. (Note: The water filter
should be mount on the wall where it is
convenient to be replaced, and do not
mount on the wall behind the refri
gerator.)
etermine the distance between the
filter and the tap, and the distance from
the filter to the fridge. Prepare lines as
required lengths. (Cut the proper lengths
of water lines which you determine to
connect with the filter inlet or outlet.)
ount the filter holder onto the wall by
using a screwdriver and attach the water

12
Note ：
：：
：
The water lines must be fully inserted into
the filter to prevent water leaking.
The line length should be less than 5m. If
the water line is too long(>5m), the ice and
cold water content may be affected due to
insufficient water pressure.
Cut the water line as required length and
avoid overbending the water lines.
It is recommended to have a suitably
qualified person to install the product.
Warning!
The water filter must be held upright as
shown in the figure above. It is critical to
connect the water inlet and outlet hoses
on the filter correctly.
Never mount the filter onto the
refrigerator. Coolant pipes might be
pierced.
Installing the water lines of the filter
To install the water lines of the filter,
follow the instructions of installing steps
below that referring to the figures supplied.
1. Take the 2 clips out, then pull out the 2
stopper of the water filter.
2. Fully insert the water lines into the Inlet
and Outlet of the water filter.
3. Insert the 2 clips in the proper position
as the figure shown below, and confirm
that each clip holds the water line firmly.
Connecting the filter inlet line to the
water supplier
The connector and the check valve is
provided as one part. You should use the
new connector incidentally but not the old
one you have.
Screw the adaptor onto a suitable 3/4”
BSP connector water outlet, and use the
spanner to tighten it. Fully insert the water
line into the check valve. Then insert the
clip in the install pack as the figure shown
below.
Note:
After installed the filter, please open the
water valve to flush the filter for 5 minutes
before use.

13
The initial dark discoloration of water is
normal.
The water lines must be connected
with the potable water only.
To operate properly, the ice maker
requires a water pressure of 2 7~689
Kpa.
Connect filter outlet line to the fridge
The outlet line of the water filter should be
connected with the inlet line of the
refrigerator by a Two-Way Connector.
The water lines must be fully inserted into
the center of the connector to prevent
water leaking.
Insert the 2 clips in the install pack as
shown in the diagram, and then confirm
that each clip holds the line firmly.
Open the water valve to flush the lines,
and check leakage in the water
connectors. If any leak, please check that
if the lines are fully inserted where the
connector leaked. If not, please install
them again, and make sure that the lines
are fully inserted.
Note:
After connect the filter outlet line with the
refrigerator(as shown in the diagram
below), please dispense several cups of
water to flush the lines before use.
The water lines should not be pressed by
heavy things and should not bend too
much.
Warning!
After turning on the water valve, make
sure that there is no leakage at all
connection points of the water lines. If
there is a leakage, turn off the valve
immediately and tighten the water
connector or make the lines fully inserted
into the connector.
Do not pull the water lines hard, it may
damage the water system.

14
Description of the appliance
Note ！
！！
！
Due to unceasing modification of our products, your refrigerator may be slightly different
from this instruction manual, but its functions and using methods remain the same.
To get the best energy efficiency of this product, please place all shelves, drawers and
baskets on their original position as the illustration above.
RF702N4IS11
FMN544I20S
RF702N4IS11
FMN544I20S

15
Note ！
！！
！
Due to unceasing modification of our products, your refrigerator may be slightly different
from this instruction manual, but its functions and using methods remain the same.
To get the best energy efficiency of this product, please place all shelves, drawers and
baskets on their original position as the illustration above.

16
Display Controls
Use your appliance according to the following control guidelines. The control panel on the
top cover shows in the diagram below, it may be different depending on the model.
When the appliance is powered on for the
first time, the backlighting of the icons on
the display panel starts working. If no
buttons have been touched or the doors
are closed, the backlighting will turn off
after 6 seconds.
The control panel consists of two areas
about temperature, and one area about
different modes.
Caution!
When you set a temperature, you set an
average temperature for the whole
refrigerator cabinet. Temperatures inside
each compartment may vary from the
temperatures displayed on the panel,
depending on how much food you store
and where you place it. High or low room
temperature may also affect the actual
temperature inside the appliance.
“
““
“ Ice Control ”
””
”
This button controls the ice maker. You
can touch "Ice On " button to control the
ice maker. When the "ice On " function
light is on, the ice maker is working. If you
want to turn off the ice maker, please
touch the "Ice On " button again.
“
““
“ Super Freeze ”
””
”
If you want to decrease the time needed to
freeze products in the Freezer, please
touch this button, the super cool icon
“ ”
will be illuminated, the fridge temperature
setting displays -24 ℃ .
Super Freezer can quickly lower the
temperature and freeze your food faster
than usual. This can retain more of the
vitamins and nutrition in fresh food and
keep your food longer.
The super freeze option allows you to
freeze the maximum amount of possible.
We recommend that you let the appliance
operates for 6 hours first. Super freeze
automatically switches off after about 52
hours, and the freezer temperature setting
will revert back to the previous setting.
When the super freeze function is on, you
can touch “ Super Freeze ” button again
to switch off. And it will not retain the
Super Freeze function when power off.
“
““
“ Water Filter ”
””
”
In general, you should change the water
filter every 6 months to ensure the highest
possible water quality.
After the refrigerator has dispensed about
1 gallons of water(used the water filter
for about 6 months), the filter icon “ ”
will blink, that remind you need to replace
the water filter.
First of all, you need to purchase a new
water filer. You can purchase the new filter
from the retailer where you purchased
your refrigerator or the after-sales service
system. Before that please check that the
new filter is the same filter type as before

17
that can be
correctly used in your
refrigerator.
After you change a new water filter,
to touch and hold the
“
“ Super Freeze ” buttons
for 3 seconds to
make the blink off.
When you replace the
water filter, so
me water may leak from the
filter and lines
. Please let the water flow in
a pan, and wipe up any leakage that
have occurred.
“
““
“
Freezer temperature control
You can touch the “
Freezer
activate the mode to control the
temperature. When you press
continuously, the
temperature will be set in
the following sequence.
“
““
“
Fridge temperature control
You can touch the “
Fridge
activate the mode to control the fridge
temperature. When you touch the
continuously, the temperature
the following sequence.
“
““
“ Super Cool ”
””
”
If you want to decrease the ti
cool products in the Fridge,
this button, the super cool icon
illuminated, the fridge
temperature setting
displays 2 ℃ .
Super cool automatically switches off
3 hours, and the refrigerator
setting will revert back to
setting.
correctly used in your
After you change a new water filter,
ensure
“
Ice On ” and
for 3 seconds to
When you replace the
me water may leak from the
. Please let the water flow in
a pan, and wipe up any leakage that
may
Freezer temperature control
”
””
”
Freezer
” button to
activate the mode to control the
freezer
temperature. When you press
the button
temperature will be set in
Fridge temperature control
”
””
”
Fridge
” icon to
activate the mode to control the fridge
temperature. When you touch the
button
continuously, the temperature
will be set in
If you want to decrease the ti
me needed to
cool products in the Fridge,
please touch
this button, the super cool icon
“ ” will be
temperature setting
Super cool automatically switches off
after
3 hours, and the refrigerator
temperature
setting will revert back to
the previous
When super cool function is on, you
touch the “ Super Cool
”
switch it off. The fridge will
Super Cool function
when power
“
““
“ Holiday ”
””
”
If you are going to be away for a long
period of time such as a long holiday
business trip, you can activate this
function by touching the “
Holiday
and the icon “ ” will be
illuminated.
When the holiday function is
temperature of the
fridge is automatically
switched to 15 ℃
and the freezer to
to
minimize the energy consumption.
When the holiday function is on, you
switch off it by touching
“
and the icon “ ”
will be off.
holiday
function is on, the
Super Freeze/ Super Cool
automatically turn off.
The refrigerator will
retain the setting
when powered off.
Note:

Do not store any food in the
the “ Holiday ”
time, or it
deteriorate.
 The refrigerator
temperature setting will
revert back to
the previous
holiday function is off.

If word "Power on/Off 3s" is under this
button, you can
switch on or switch off
your appliance by press this b
for
3 seconds, after a buzzer sound, the
appliance will be turned off
“
““
“ Power on/off ”
””
”
(Optional)
You can switch on or switch off your
appliance by press this bu
tton
Alarm
When super cool function is on, you
can
”
button again to
switch it off. The fridge will
not retain the
when power
off.
If you are going to be away for a long
period of time such as a long holiday
or
business trip, you can activate this
Holiday
” button,
illuminated.
When the holiday function is
activated, the
fridge is automatically
and the freezer to
-18 ℃
minimize the energy consumption.
When the holiday function is on, you
can
“
Holiday ” again,
will be off.
When the
function is on, the
Ice maker/
Super Freeze/ Super Cool
will
The refrigerator will
when powered off.
Do not store any food in the
fridge during
time, or it
will quickly
temperature setting will
the previous
setting after the
If word "Power on/Off 3s" is under this
switch on or switch off
your appliance by press this b
utton. Press
3 seconds, after a buzzer sound, the
appliance will be turned off
or turn on.
(Optional)
You can switch on or switch off your
tton
.

18
When the door of fridge or freezer has
been opened for over 2 minutes, the door
alarm will sound. In case of door alarm,
buzzer will sound 3 times every 1 minute
and will stop alarming automatically after 8
minutes.
To save energy, please avoid keeping the
door open for a long time when using the
appliance. The door alarm can also be
cleared by closing the door.
Using your appliance
This section tells you how to use most of the useful features. We recommend that you
read through them carefully before using the appliance. it may be different depending on
the model
1. Using your refrigerator compartment
The refrigerator compartment is suitable
for storage of vegetables and fruit. Food
inside should be packed to store in order
to avoid losing moisture or flavor
permeating into other foods.
Caution! Never close the refrigerator door
while the shelves, crisper and/or
telescopic slides are extended. It may
damage both them and the refrigerator.
Glass shel es and Door racks
The refrigerator compartment is provided
with several glass shelves and several
different door racks, which are suitable for
the storage of eggs, canned liquid, bottled
drinks and packed food. They can be
placed a different heights according to
your need. But do not place too many
heavy things in racks. Before you lift up
the door shelf vertically, please take the
food out.
Note: All the door racks and shelves can
be taken out to be cleaned.
When you remove the shelves, gently pull
them forward until the shelf comes clear of
the shelf guides.
When you return the shelves, make sure
there is no obstacle behind and gently
push the shelf back into the position.
Drawers
These are suitable for storage of fruits and
vegetables. And it can be taken out to be
cleaned.
To take them out, open the door to the
final location first. Then pull out the drawer
and tilt up the front of the crisper after
moving slightly in the direction.
Sealing board(optional)
Sealing board can partly prevent water
desorption of food in the fruit and
vegetable crisper. You can move the slider
to control the humidity of crisper.
Note:
Put too much food in crisper may impact
the function of sealing board.
2. Using the dispenser (optional)
Getting cold water
The water dispenser is located on the left
fridge door. Move your cup down the

19
dispenser lever in the suggested position
and press it.
Note:


Don't push the dispenser lever forward
without cup, it may cause the water leak
from the dispenser.


Do not immediately removing your cup or
glass from the dispenser after dispensing
water you need. You should wait for 2 or 3
seconds to prevent spills.
Do not pull the lever out, it could damage
or break the lever’s spring.
Dispenser does not work when door is
not closed.
Take water frequently or largely or you
first use this function, the water may not
cold enough. Please wait for some time to
ensure the appropriate temperature.

Water clouding phenomenon
All water provided to the refrigerator flows
through the filter which is an alkaline water
filter. In the filtering process, the pressure
of the water that has flowed out of the filter
is increased, and the water becomes
saturated with oxygen and nitrogen. When
this water flows out into the air, the
pressure plummets and the oxygen and
nitrogen get supersaturated, which results
in gas bubbles. The water may temporarily
look misty or cloudy due to these oxygen
bubbles. After a few seconds, the water
will look clear.
3. Using the freezer compartment
The freezer compartment is provided with
an upper drawer, a lower drawer and a ice
box （ optional ） . To remove all of them, refer
to page 1 for disassembly instruction.
Automatic Icemaker (optional)
Automatic Icemaker can make ice
automatic 。
Note:
When the ice maker dumps ice into the
ice box, any sounds you hear are part of
normal operation.
If you do not dispense ice for a long
periods of time, Ice may clump in the Ice
box. If this occurs, please remove all the
ice and empty the box
If you are going on a long vacation or
business trip and won’t be using the water
dispenser or ice maker part for period of
time, please close the water valve to
prevent leaks.
The ice made by the ice maker first
batches cannot be used for eating or
drinking cause it is unhealthiness.
Cannot store liquid cans in ice box, it
may cause burst.
warning!
Do not allow your children to hang off the
dispenser or touch the ice maker. This
could cause injury.

2
Cleaning and care
For hygienic reasons the appliance
(including exterior and interior accessories)
should be cleaned regularly at least every
two months.
Caution!
The appliance must not be connected to
the mains during cleaning. Danger of
electrical shock! Before cleaning switch
the appliance off and remove the plug
from the mains socket.
Exterior cleaning
To maintain good appearance of your
appliance, you should clean it regularly.
Spray water onto the cleaning cloth
instead of spraying directly on the
surface of the appliance. This helps
ensure an even distribution of moisture to
the surface.
Clean the doors, handles and cabinet
surfaces with a mild detergent and then
wiped dry with a soft cloth.
Caution!
Don’t use sharp objects as they are likely
to scratch the surface.
Don’t use Thinner, Car detergent, Clorox,
ethereal oil, abrasive cleansers or
organic solvent such as Benzene for
cleaning. They may damage the surface
of the appliance and may cause fire.
Interior cleaning
You should clean the appliance interior
regularly. It will be easier to clean when
food stocks are low. Wipe the inside of the
fridge freezer with a weak solution of
bicarbonate of soda, and then rinse with
warm water using a wrung-out sponge or
cloth. Wipe completely dry before
replacing the shelves and baskets.
Thoroughly dry all surfaces and removable
parts before putting them back into place.
Although this appliance automatically
defrosts, a layer of frost may occur on the
freezer compartment ’ s interior walls if
the freezer door is opened frequently or
kept open too long. If the frost is too thick,
choose a time when the freezer is nearly
empty and proceed as follow:
1. Remove existing food and accessories
baskets, unplug the appliance from the
mains power and leave the doors open.
Ventilate the room thoroughly to
accelerate the process.
2. When defrosting is completed, clean
your freezer as described above.
Warning!
Do not use sharp objects to remove frost
from the freezer compartment. Only after
the interior is completely dry should the
appliance be switched back on and
plugged back into the mains socket.
Door seals cleaning
Take care to keep door seals clean. Sticky
food and drinks can cause seals to stick to
the cabinet and tear when you open the