Hisense ES-L215110 User manual

Before installing this product, read this guide carefully and
make sure you understand all of the content.
INSTALLATION GUIDE
Hisense Laser TV Screen
ENGLISH
ES-L215110

1
Structure diagram of laser TV screen
* The above are only the specifications of some main products. If there is a small deviation in the size of the
laser TV screen, it is a normal installation measurement error. Please feel free to use it.
100 inches
Parameters for laser TV screen
Name Fresnel laser TV screen 100 inches
Size 100" Screen material PET Projection scale 16:9
Projected area 2214 × 1245 mm Net weight 11.7 kg Screen color Grey
Screen size 2250 × 1280 × 30 mm Total weight 24.5 kg Border color Black
Package size 1665 × 430 × 255 mm Horizontal full view 45 ± 5° Gain ≥1.0

Q1
Q2
R
N
J2
M
M
H
J1
J1
B
A1
A2
F
2
Overall structure diagram of laser TV screen

3
Tool preparation before installation
Tape measure ×1 Electric drill × 1 Woodworking pencil × 1 Screw driver × 1 Hammer × 1 Metal detector × 1 Level ruler × 1
Hardware and Parts List
The appearance drawn in this manual is a schematic diagram. Please refer to the purchased actual object. After
opening the package, please carefully check the parts list.
Code Name Picture Quantity Code Name Picture Quantity
A1 Long side
inner frame (A1) 2 A2 Long side
inner frame (A2) 2
BShort side
inner frame 2 C
Long side inner
frame connectors
and screw
2
D
Inner frame
Iconnector
and screws
4 E
M6 × 6 inner
frame corner
screw
24
F Vertical beam 1 G
Vertical beam
pressing plate
and screw
2
HTentorial
surface 1 I Protective sheet 1
J1 Fiber rod
(short) 4 J2 Fiber rod
(long) 2
K Pull pin nut 20 L M4 × 45 pull pin
screw 20
MLong side tie
rod 4 N Short side tie rod 2

4
Code Name Picture Quantity Code Name Picture Quantity
OOuter frame
connector 4 P
Outer frame
splicing
connector
2
Q1 Long side outer
frame (Q1) 2 Q2 Long side outer
frame (Q2) 2
RShort outer
frame 2 S
M3 × 6 outer
frame splicing
screw
24
TM3 × 6 outer
frame screws 18 U Cushion block 2
VWall hanging
support 2 W Adjusting rod 2
X
Wall hanging
support
connecting rod
2 Y Gloves for
installation 2
Z1
Plastic
expansion pipe
and screw
4 Z2 M4 hexagon
socket screwdriver 2
Z3 Clé
hexagonale M3 2
Maintenance of laser TV screen
Warning
Use dust-free soft cotton cloth dipped in absolute ethanol to gently wipe the and frame.
Please read this manual carefully before using and keep it properly for reference.
• Do not touch or wipe the screen with an ordinary towel.
• Do not expose the screen to dripping or splashing.
• Do not place the screen on an unstable cart, tripod or desktop. Dropping may cause serious damage and
injuries.
• Do not scratch or touch the screen with hard or sharp objects.
• Do not expose the screen to direct sunlight.
• Do not place the screen near inflammable, explosive and other dangerous objects.

5
Screen assembly steps
( I ) Assemble inner frame
First, find the white protective sheet (1) in the packing box, spread out the sheet and lay it on the clean ground for
the following installation:
1. Take out all the frames from the foam cotton and gently put them on the sheet separately. Check whether they
are missing according to the parts list. Place the inner frame correctly according to the illustration below. Splice
upper and lower inner frames (A1) and upper and lower inner frames (A2) with inner frame connectors (C).
(Methods: Insert one end of the upper and lower inner frame (A 1) into the inner frame connectors (C), align it with
the hole on the inner frame, use a piece of inner frame corner screw (E) to fix the inner frame, and then connect it
with another upper and lower outer frame (A2). Repeat this step to splice the other two sections of the frame), and
the two left and right inner frames (B) are inserted into the inner frame connector (D), which are connected with
the spliced long inner frame.
BA1
D
E
A1
A2
A2
B
C
G

6
Disassemble the bracket and take out the screen
Unroll the screen surface on the mat
(II) Installation of screen surface
1. Loosen the screws on the brackets at both ends of the paper tube with an M4 Allen screw wrench (Z2), remove
the brackets on both sides, slowly remove the screen surface from the paper tube, and wear installation gloves
to prevent the screen surface from being stained with sweat. Carefully unroll the screen surface and lay it on the
sheet with the back of the screen facing upward (the side with the label is the back). Please refer to the following
illustration for this step:

7
2. There are 6 fiber rods in total, of which 4 are of the same length and are used for two long sides. Insert 4 fiber (J1)
rods into the sleeves of the long sides, and the other 2 slightly longer fiber rods (J2) into the sleeves of the short sides.
J1
J1
J1
J1
J2
J2
Down

8
M
M
M
M
N
N
3. Slide the screen edges into grooves of the pull rod (N) and pull rod (M) as shown in the illustration below.
4. Center the inner frame on the back of the screen surface.
Down
Down

9
5. Ensure that the four sides of the screen are aligned with the outer edge of the frame. The M4 × 45 pull nail screw
(L) is screwed into the Pull pin nut (K) in pull rod through the hole in the inner frame hole. Install the four corners
first according to the installation sequence of 1-1 → 2-2 → 3-3 → 4-4 in the illustration, first the long side and then
the short side. Pre tighten the screws to ensure that the four sides of the screen are aligned, and then tighten the
screws symmetrically. The frame screws can be tightened to the side of the pull rod and close to the positioning line.
If the screen surface is not flat, adjust the tension of the pull screws until the screen surface is flat.
Down