Hitachi L300P-110L User manual

Hitachi Europe GmbH
Instruction Manual
HITACHI Inverter
L300P Series - ... HFE
Three phase input 200/400V class
NB601EX

i
SAFETY
For the Best Results with L300P Series inverter, read this manual and all of the warning sign attached
to the inverter carefully before installing and operating it, and follow the instructions exactly. Keep this
manual handy for your quick reference.
Definitions and Symbols
A safety instruction (message) is given with a hazard alert symbol and a signal word;
WARNING or CAUTION. Each signal word has the following meaning throughout this manual.
This symbol means hazardous high voltage. It used to call your attention to
items or operations that could be dangerous to you or other persons
operating this equipment.
Read these message and follow these instructions carefully.
This is the "Safety Alert Symbol" This symbol is used to call your attention to
items or operations that could be dangerous to you or other persons operating
this equipment.
Read these messages and follow these instructions carefully.
WARNING WARNING
Indicates a potentially hazardous situation which, if not avoided, can result in
serious injury or death.
CAUTION CAUTION
Indicates a potentially hazardous situation which, if not avoided, can result in
minor to moderate injury, or serious damage of product.
The matters described under may, if not avoided, lead to serious
results depending on the situation. Important matters are described
in CAUTION ( as well as WARNING ), so be sure to observe them.
NOTE NOTE
Notes indicate an area or subject of special merit, emphasizing either the
product's capabilities or common errors in operation or maintenance.
HAZARDOUS HIGH VOLTAGE
Motor control equipment and electronic controllers are connected to hazardous line voltages. When
servicing drives and electronic controllers, there might be exposed components with cases or protru-
sions at or above line potential. Extreme care should be taken to product against shock.
Stand on an insulating pad and make it a habit to use only one hand when checking components.
Always work with another person in case an emergency occurs. Disconnect power before checking
controllers or performing maintenance. Be sure equipment is properly grounded. Wear safety glasses
whenever working on an electronic controllers or rotating electrical equipment.
CAUTION

ii
PRECAUTION
:This is equipment should be installed, adjusted and serviced by qualified electrical
maintenance personal familiar with the construction and operation of the equipment and the hazards
involved. Failure to observe this precaution could results in bodily injury.
:The user is responsible for ensuring that all driven machinery, drive train
mechanism not supplied by Hitachi, Ltd., and process line material are capable of safe operation at an
applied frequency of 150% of the maximum selected frequency range to the AC motor. Failure to do
so can result in destruction of equipment and injury to personnel should a single point failure occur.
: For protection, install an earth leakage breaker with a high frequency circuit
capable of large currents to avoid an unnecessary operation. The ground faults protection circuit is not
designed to protect personal injury.
: HAZARD OF ELECTRICAL SHOCK. DISCONNECT INCOMING POWER
BEFORE WORKING ON THIS CONTROL.
:SEPARATE MOTOR OVERCURRENT, OVERLOAD AND OVERHEATING
PROTECTION IS REQUIRED TO BE PROVIDED IN ACCORDANCE WITH THE SAFETY CODES
REQUIRED BY JURISDICTIONAL AUTHORITIES.
:These instructions should be read and clearly understood before working on
L300P series equipment.
:Proper grounds, disconnecting devices and other safety devices and their location
are the responsibility of the user and are not provided by Hitachi, Ltd.
: Be sure to connect a motor thermal switch or overload devices to the L300P
series controller to assure that inverter will shut down in the event of an overload or an overheated
motor.
:DANGEROUS VOLTAGE EXISTS UNTIL CHARGE LAMP IS OFF.
: Rotating shafts and above ground electrical potentials can be hazardous.
Therefore, it is strongly recommended that all electrical work conform to the National Electrical Codes
and local regulations. Installation, alignment and maintenance should be performed only by qualified
personnel. Factory recommended test procedures, included in the instruction manual, should be
followed. Always disconnect electrical power before working on the unit.
NOTE : POLLUTION DEGREE 2
The inverter must be used environment of the degree 2.
Typical constructions that reduce the possibility of conductive pollution are;
1) The use of an un-ventilated enclosure
2) The use of a filtered ventilated enclosure when the ventilation is fan forced that is, ventilation is
accomplished by one or more blowers within the enclosure that provide a positive intake and
exhaust.
WARNING
WARNING
WARNING
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
WARNING

iii
Cautions for EMC (Electromagnetic Compatibility)
You are required to safety the EMC directive (89/336/EEC) when using the L300P inverter in a
European country. To safety the EMC directive and to comply with standard, follows the checklist
below.
:This equipment should be installed, adjusted, and serviced by qualified
personal familiar with construction and operation of the equipment and the hazards
involved. Failure to observe this precaution could result in bodily injury.
1.The power supply to L300P inverter must meet these specifications:
a. Voltage fluctuation +/-10% or less.
b. Voltage imbalance +/-3% or less.
c. Frequency variation +/-4% or less.
d. Voltage distortion THD = 10% or less.
2.Installation measure:
a. Use a filter designed for L300P inverter.
3.Wiring
a. Shielded wire (screened cable) is required for motor wiring, and the length must be less than 20
meters.
b. The carrier frequency setting must be less than 3 kHz to satisfy EMC requirements.
c. Separate the main circuit from the signal/process circuit wiring.
d. In case of remote operating with connector cable, the inverter does not conform to EMC.
4.Environmental conditions – when using a filter, follow these guidelines:
a. Ambient air temperature: -10 - +40 ºC.
b. Humidity: 20 to 90% RH (non-condensing)
c. Vibration: 5.9 m/sec2(0.6 G) 10 – 55Hz. (L300P-110-300LF/110-300HF)
2.94 m/sec2(0.3 G) 10 – 55Hz. (L300P-370-750LF/370-1320HF)
d. Location: 1000meters or less altitude, indoors (no corrosive gas or dust)
Conformity to the Low Voltage Directive (LVD)
The protective enclosure must conform to the Low Voltage Directive.
The inverter can conform to the LVD by mounting into a cabinet or by adding covers as follows.
1.Cabinet and Cover
The inverter must be installed into a cabinet which has the protection degree of Type IP2X. In
addition the top surfaces of cabinet that are easily accessible shall meet at least the requirements of
the Protective Type IP4X, or which is constructed to prevent small objects from entering inverter.
Fig. Inverter cabinet
WARNING

iv
UL Warnings and Cautions Manual for L300P series
This auxiliary instruction manual should be delivered to the end user.
1.Wiring Warnings for Electrical Practices and Wire Specifications
(1) ! WARNING : "Use 60/75 ºC CU wire only" or equivalent.
(2) ! WARNING : "Open Type Equipment."
For models with L300P 900-1320H.
(3) ! WARNING : "Suitable for use on a circuit capable or delivering not more than 10,000 rms
symmetrical amperes, 240 V maximum." For models with suffix L.
(4) ! WARNING : "Suitable for use on a circuit capable or delivering not more than 10,000 rms
symmetrical amperes, 480 V maximum." For models with suffix H.
2.Tightening Torque and Wire Range
(1) ! WARNING : Tightening torque and wire range for field wiring terminals are marked
adjacent to the terminal or on the wiring diagram.
Model Name Tightening Torque [N•m] Wire Range (AWG)
L300P-110L 4.9 4
L300P-150L 4.9 2
L300P-185L 4.9 1
L300P-220L 8.8 1/0
L300P-300L 8.8 2/0
L300P-370L 8.8 3/0 or 2 parallel of 1 AWG
L300P-450L 13.7 250kcmil or 2 parallel of 1 AWG (75ºC)
L300P-550L 13.7 350kcmil or 2 parallel of 1/0 AWG
L300P-750L 13.7 350kcmil or 2 parallel of 1/0 AWG
L300P-110H 4.9 8
L300P-150H 4.9 6
L300P-185H 4.9 6
L300P-220H 4.9 4
L300P-300H 4.9 3
L300P-370H 4.9 1

v
L300P-450H 8.8 1
L300P-550H 8.8 1/0
L300P-750H 8.8 250kcmil or 2 parallel of 1 AWG (75ºC)
L300P-900H 13.7 250kcmil or 2 parallel of 1 AWG (75ºC)
L300P-1100H 13.7 350kcmil or 2 parallel of 1/0 AWG
L300P-1320H 13.7 350kcmil or 2 parallel of 1/0 AWG
3.Circuit Breaker / Fuse Size
(1) ! WARNING : Distribution fuse/circuit breaker size marking is included in the manual to
indicate that the unit shall be connected with an UL Listed inverse time circuit
breaker, rated 600 V with the current ratings or an UL Listed fuse as shown
in the table below.
Model Name Tightening Torque [N•m] Wire Range (AWG)
L300P-110L 60 60
L300P-150L 70 70
L300P-185L 90 90
L300P-220L 100 100
L300P-300L 150 150
L300P-370L 175 175
L300P-450L 200 200
L300P-550L 250 250
L300P-750L 300 300
L300P-110H 30 30
L300P-150H 35 35
L300P-185H 50 50
L300P-220H 50 50
L300P-300H 70 70
L300P-370H 80 80
L300P-450H 100 100
L300P-550H 125 125
L300P-750H 150 150
L300P-900H - 200
L300P-1100H - 225
L300P-1320H - 300

vi
4.Others
(1) ! WARNING : "Field wiring connection must be made by an UL Listed and CSA Certified
closed-loop terminal connector sized for the wire gauge involved. Connector
must be fixed using the crimp tool specified by the connector manufacturer.",
or equivalent wording included in the manual.

vii
Revision History Table
No. Revision Contents The Date
of Issue Operation Manual No.
1 Initial Release of Manual NB601AX Sep. 1999 NB601AX
2The data 02 of the command b004 was added
The carrier frequency of the capacity 37kW and more was added. Oct. 1999 NB601BX
3 The specification of the capacity 75kW and more was added. Jun. 2000 NB601CX
4 A skipped number. NB601DX
5 The specification of the capacity 90-132kW and more was added Feb. 2001 NB601EX

viii
SAFETY PRECAUTIONS
1.Installation
• Be sure to install the unit on flame resistant material such as metal.
Otherwise, there is a danger of fire. …… p.2-2
• Be sure not to place anything inflammable in the vicinity.
Otherwise, there is a danger of fire. …… p.2-2
• Do not carry unit by top cover, always carry by supporting base of unit.
There is a risk of falling and injury. …… p.2-2
• Be sure not to let the foreign matter enter such as cut wire refuse, spatter
from welding, iron refuse, wire, dust, etc.
Otherwise, there is a danger of fire. …… p.2-5
• Be sure to install it in a place which can bear the weight according to the
specifications in the text. (Chapter 6. Specifications)
Otherwise, it may fall and there is a danger of injury. …… p.2-1
• Be sure to install the unit on a perpendicular wall which is not subject to
vibration.
Otherwise, it may fall and there is a danger of injury. …… p.2-3
• Be sure not to install and operate an inverter which is damaged or parts of
which are missing.
Otherwise, there is a danger of injury. …… p.2-2
• Be sure to install it in a room which is not exposed to direct sunlight and is
well ventilated. Avoid environments which tend to be high in temperature,
high in humidity or to have dew condensation, as well as places with dust,
corrosive gas, explosive gas, inflammable gas, grinding-fluid mist, salt
damage, etc.
Otherwise, there is a danger of fire.
…… p.2-2
CAUTION

ix
SAFETY PRECAUTIONS
2.Wiring
• Be sure to ground the unit.
Otherwise, there is a danger of electric shock and/or fire. …… p.2-9
• Wiring work shall be carried out by electrical experts.
Otherwise, there is a danger of electric shock and/or fire. …… p.2-6
• Implement wiring after checking that the power supply is off.
It might incur electric shock and/or fire. …… p.2-8
• After installing the main body, carry out wiring.
Otherwise, there is a danger of electric shock and/or injury. …… p.2-5
• Do not remove the rubber bush. (11 to 75kW)
Due to the possibility that a wire may be damaged, shorted or may have
a ground fault with the edge of the wiring cover. …… p.2-4
• Make sure that the input voltage is:
Three phase 200 to 240V 50/60Hz (for models with suffix L)
Three phase 380 to 480V 50/60Hz (for models with suffix H) …… p.2-6
• Be sure not to input a single phase.
Otherwise, there is a danger of fire. …… p.2-8
• Be sure not to connect AC power supply to the output terminals(U, V, W).
Otherwise, there is a danger of injury and/or fire. …… p.2-5
• Be sure not to connect the resistor to DC terminals (PD,P and N) directly.
Otherwise, there is a danger of fire. …… p.2-5
• Be sure to set the earth leakage breaker or the fuse(s) (the same phase as
the main power supply) in the operation circuit.
Otherwise, there is a danger of fire. …… p.2-12
• As for motor leads, earth leakage breakers and electromagnetic contactors,
be sure to use the equivalent ones with the specified capacity (rated).
Otherwise, there is a danger of fire. …… p.2-12
• Do not stop operation by switching off the electromagnetic contactors on the
primary or secondary sides of the inverter.
Otherwise, there is a danger of injury and/or machine breakage. …… p.2-6
• Fasten the screws with the specified fastening torque. Check so that there
is no loosening of screws.
Otherwise, there is a danger of fire. …… p.2-12
WARNING
CAUTION