Hitachi GP 2 User manual

Sleipner Motor A/S Sleipner Motor A/S
User manual
Sidepower
Tunnel Cut-out Tool
Art. No. 6 8870 / 6 8871
Ver.1 - 2007

Sleipner Motor A/S Sleipner Motor A/S

Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diameter

Sleipner Motor A/S Sleipner Motor A/S
- Assemble the cut-out tool, and adjust it to the right tunnel
diameter. After finger-tightening the two threaded handles,
tighten the adjustment-screw to get the right A-distance
Thruster Position at cut-out tool Distance A
SP35S 125 Min. 74mm
Min. 2 15/16”
SP55S, SP75T, SP95T,
SP100HYD
185 Min. 105mm
Min. 4 1/8”
SP125T, SP155TC,
SP200TC, SP200HYD
250 Min. 140mm
Min. 5 ½”
SP220TC, SP285TC,
SP300HYD
300 Min. 167mm
Min. 6 9/16”
SP550TC HYD 386 Min. 213mm
Min. 8 3/8”
Use the table for selection of position and adjustment of the cut-out tool. Adjustment-screw at Ø125mm tunnel
Adjustment-screw at Ø386mm tunnel

Sleipner Motor A/S Sleipner Motor A/S
- Assemble the cut-out tool, and adjust it to the right tunnel
diameter. After finger-tightening the two threaded handles,
tighten the adjustment-screw to get the right A-distance
Thruster Position at cut-out tool Distance A
SP35S 125 Min. 74mm
Min. 2 15/16”
SP55S, SP75T, SP95T,
SP100HYD
185 Min. 105mm
Min. 4 1/8”
SP125T, SP155TC,
SP200TC, SP200HYD
250 Min. 140mm
Min. 5 ½”
SP220TC, SP285TC,
SP300HYD
300 Min. 167mm
Min. 6 9/16”
SP550TC HYD 386 Min. 213mm
Min. 8 3/8”
Use the table for selection of position and adjustment of the cut-out tool. Adjustment-screw at Ø125mm tunnel
Adjustment-screw at Ø386mm tunnel

Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diameter

Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diameter

Sleipner Motor A/S Sleipner Motor A/S
- Insert the cut-out tool through both ø12mm holes.
- Start the grinder and mark the cutting path by frimly rotating
the cut-out tool. Be careful to avoid flexing the rod.
Use eye- and earprotection. Cut out the hole for the tunnel.
NB! Leave 3 small spots to maintain the bearing until you have
cut out the hole on the oposite side of the boat.
Tunnel Cut-out tool adjusted for 300mm tunnel diameter