HME NEXEO HDX TI7000 User manual

Quick Reference Installation Guide
HM ELECTRONICS, INC.
2848 Whiptail Loop, Carlsbad, CA 92010 USA
Phone: [phone] Fax: [phone]
Website: www.hme.com Email: [email protected]
HME# PUB-00215
Rev A 01/06/23
NEXEO | HDX™ TI7000 TELEPHONE INTERFACE
The TI7000 provides the hardware necessary to link
a telephone to the NEXEO®System. It allows one
HS7000 Headset to be used to answer incoming phone
calls.
TOOLS/EQUIPMENT REQUIRED (wall mounting only)
• Drill and drill bits (~ 3/16th inch (4.8 mm))
• Screwdriver (Phillips #2)
• Safety Glasses
INSTALLATION AND SETUP
Note: The base station interface cable is short (3 ft
(0.91 m)) so mount the TI7000 close to the NEXEO
Base Station.
Wall mount instructions:
1. Hold the TI7000 against the wall and mark the wall
through the two mounting holes on each end of the
unit (see Fig. 1).
2. Drill two holes at the marked locations (avoid elec-
trical or plumbing obstructions).
3. Insert the included screw anchors until flush with
the wall.
4. Use a screwdriver to securely mount the TI7000 to
the wall using the included hardware.
Connections:
1. Unplug the store telephone from the wall port and
plug the included telephone jack splitter into the
same wall port.
2. Plug the telephone into one of the two ports on the
telephone jack splitter, see Fig 1.
3. Use the included telephone interface cable, plug
it into the other port on the telephone jack splitter
and connect the other end to the RJ11 port on the
TI7000. See Fig 1 and 2.
4. Open the Base Station and connect the included
base station interface cable from the RJ45 port
on the TI7000 to J201 on the base station PCBA
(see Fig. 3 for J201 location and Table 1 for J201
callout if necessary).
TI7000
NEXEO BASE STATION
FRONT VIEW
TELEPHONE
JACK SPLITTER
TELEPHONE
Base Station
Interface cable
Mounting Holes
Telephone Interface cable
Wall Port
Fig. 2
Fig. 3
PCBA Partial View
Fig. 1
POWER
ON/OFF
RINGER
ON/OFF
STATUS LIGHT
BS INTERFACE CABLE
TO J201 on
NEXEO BASE STATION
TELEPHONE INTERFACE
CABLE TO TELEPHONE
JACK SPLITTER
TI7000 TELEPHONE INTERFACE MODULE
(CONNECTOR VIEW)
RJ11RJ45
NEXEO BASE STATION PCBA
Remote
Module 1
Remote
Module 2
Remote
Module 3
Remote
Module 4
Ethernet
Telephone
Interface
Timer Greet
Veh Detect 1
Timer Greet
Veh Detect 2
Veh Detect
Inputs
Alert
Inputs
Remote
Switches
Early
Warnings
Power
In
DC +
DC -
GND
USB
Type C
J200
J600
J201 J800 J801 J802
J805
J804
J803
J2003
J3000
J4501 J4500
J1400
SW2001
J3200
J3400
J3600
J3800
1
1
1
1
1 1 1
1
1
1
1
Serial
Debug
USB
J1301
J1300
J1
Reset button to
reboot system

©2023 HM Electronics, Inc. All rights reserved.
2
A copy of this guide and more can be found by scanning this QR code or going to:
https://www.hme.com/qsr/drive-thru-user-manuals/
The HME logo and product names are registered trademarks of HM Electronics, Inc.
TI7000 Technical Specications
Dimensions 6.6" L x 4.5" W x 1.8” H (168 x 113 x 46 mm)
Weight 7.8 oz (221 g)
Power Supply Voltage: 12 VDC, powered from BS7000
Panel RJ11 and RJ45 connector type ports and two on/o switches
Wireless N/A
Temperature Operating Temperature range: -25°C (-13°F) and +60°C (+140°F)
Compliance See NEXEO | HDX - Regulatory, Compliance, and Safety Guide online
BS7000 J201 (Telephone Interface)
Pin # Label Description/wire color
1 Tel Audio In
2 Tel Power +12V
3 Tel Off Hook
4 Tel PTT
5 Tel Ring
6 Tel Active
7 Tel Ground
8 Tel Audio Out
OPERATION:
To set your headset to answer phone calls:
1. Set the POWER and RINGER switches on the
TI7000 to the ON position (the RINGER switch
enables you to hear the telephone ring tone on
the headset). The TI7000 status light turns on and
remains a steady red (until an incoming call).
2. Log in to the NEXEO base station and go to Sys-
tem>Settings. Select Telephone Interface from the
drop-down list, see Fig. 4. Toggle the OFF switch
ON and if necessary, use the sliders to adjust vol-
ume levels.
3. Pair your headset (and select name if prompted).
4. When the Select Your Position & Options dia-
log appears, select a position and check the box
labeled: Allow headset to receive phone calls. See
Fig. 5. (Since only one headset can be designated
to receive phone calls, checking the box forces any
previous headset assigned out of this mode.)
5. The headset (Action) key can now be used to
answer phone calls. Incoming calls will ring on the
headset, and the TI7000 status light will flash red.
• To answer a call: tap the key once (the
TI7000 status light turns a steady green).
• To end a call: tap the key again (the
TI7000 status light reverts to a steady red).
• To place call on hold and speak to a lane:
Tap the 1 or 2 key twice to speak to lane 1 or
2, respectively (a single tap only puts the head-
set in idle mode). To return to the call, tap 1 or
2 again to return the headset to idle, and then
tap the key. Tap again to end call.
Privacy: Only the designated headset user hears the
incoming call (other headsets cannot). If the store tele-
phone is answered first, the designated headset user
will not hear the phone conversation or vice versa).
Fig. 4
Fig. 5
Table 1