HMS eWON Netbiter EC300 Series User manual

Netbiter EC300 Series
USER MANUAL
SCM-1202-012 2.2 ENGLISH

Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any
inaccuracies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial
Networks AB, reserve the right to modify our products in line with our policy of continuous product development.
The information in this document is subject to change without notice and should not be considered as a commit-
ment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no responsibility for any errors that
may appear in this document.
There are many applications of this product. Those responsible for the use of this device must ensure that all the
necessary steps have been taken to verify that the applications meet all performance and safety requirements in-
cluding any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems that
may arise as a result from the use of undocumented features, timing, or functional side effects found outside the
documented scope of this product. The effects caused by any direct or indirect use of such aspects of the product
are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular implementation, HMS Industrial Networks AB cannot as-
sume responsibility for actual use based on these examples and illustrations.
Intellectual Property Rights
HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product de-
scribed in this document. These intellectual property rights may include patents and pending patent applications in
the USA and other countries.
eWON®, Netbiter®, and Netbiter Argos®are registered trademarks of HMS Industrial Networks AB. All other trade-
marks mentioned in this document are the property of their respective holders.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Netbiter EC300 Series User Manual SCM-1202-012 2.2
Table of Contents Page
1 Preface ............................................................................................................................... 3
1.1 About This Document.....................................................................................................3
1.2 Document history...........................................................................................................3
1.3 Document Conventions ..................................................................................................4
2 Installation ........................................................................................................................ 5
2.1 Basic Installation Steps ..................................................................................................5
2.2 Factory Reset ................................................................................................................5
2.3 Connectors....................................................................................................................6
2.4 LED Indicators............................................................................................................. 11
2.5 MODE Button ..............................................................................................................12
2.6 Wiring Examples..........................................................................................................13
3 Local Configuration...................................................................................................... 14
3.1 Connecting via USB .....................................................................................................14
3.2 Connecting via Ethernet ...............................................................................................14
3.3 Login ..........................................................................................................................14
3.4 Status .........................................................................................................................15
3.5 Network Settings – WAN ..............................................................................................17
3.6 Network Settings – LAN................................................................................................18
3.7 Firmware Update .........................................................................................................19
3.8 Modem Settings (EC350) .............................................................................................20
A EtherNet/IP Implementation ....................................................................................... 21
A.1 Client ..........................................................................................................................21
A.2 Adapter.......................................................................................................................21
B Technical Data................................................................................................................ 23
B.1 Technical Specifications ...............................................................................................23
B.2 Installation Drawings ....................................................................................................24

This page intentionally left blank

Preface 3 (26)
1 Preface
1.1 About This Document
This manual describes how to install and configure Netbiter EC300 Series gateways.
For additional documentation and software downloads, FAQs, troubleshooting guides and tech-
nical support, please visit www.netbiter.com/support.
1.2 Document history
Version Date Description
1.0 2016-10-03 First release with new layout
2.0 2017-10-07 Update for model name NB301A/B
2.1 2017-11-06 Minor update
2.2 2017-11-13 Added EC320 technical specifications
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Preface 4 (26)
1.3 Document Conventions
Ordered lists are used for instructions that must be carried out in sequence:
1. First do this
2. Then do this
Unordered (bulleted) lists are used for:
• Itemized information
• Instructions that can be carried out in any order
...and for action-result type instructions:
► This action...
➨leads to this result
Bold typeface indicates interactive parts such as connectors and switches on the hardware, or
menus and buttons in a graphical user interface.
Monospaced text is used to indicate program code and other
kinds of data input/output such as configuration scripts.
This is a cross-reference within this document: Document Conventions, p. 4
This is an external link (URL): www.hms-networks.com
This is additional information which may facilitate installation and/or operation.
This instruction must be followed to avoid a risk of reduced functionality and/or
damage to the equipment, or to avoid a network security risk.
Caution
This instruction must be followed to avoid a risk of personal injury.
WARNING
This instruction must be followed to avoid a risk of death or serious injury.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 5 (26)
2 Installation
2.1 Basic Installation Steps
This product contains parts that can be damaged by electrostatic discharge (ESD).
Use ESD protective measures to avoid equipment damage.
Connecting power with reverse polarity or using the wrong type of power supply
may damage the equipment. Make sure that the power supply is correctly
connected and of the recommended type.
Make sure that you have all the necessary information about the capabilities and restrictions of
your local network environment before installation.
1. Mount the unit on a flat surface or on a DIN rail using the adapter kit (optional).
2. Connect the slave devices and/or Ethernet network as needed.
3. For mobile networking (EC350), connect the mobile antenna and insert the SIM card.
4. Connect a suitable power supply and apply power.
5. Configure the unit.
Modbus Interfaces
Modbus devices can be connected to more than one interface and/or physical connection on
Netbiter EC300 Series gateways. These interfaces must also be enabled in Netbiter Argos be-
fore they can be used. See the Netbiter Argos documentation for more information.
2.2 Factory Reset
Keep the MODE button pressed while powering on to reset to the factory default settings.
Fig. 1 Factory reset
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 6 (26)
2.3 Connectors
2.3.1 I/O Terminal Block
Fig. 2 Terminal block
Pin Label Function Note
15 HI CAN High
J1939
14 PE CAN Shield
13 LO CAN Low
12 GND CAN Ground
11 COM Analog Input common
10 AI4 Analog Input 4 0–20 mA or 0–10 VDC
9 AI3 Analog Input 3 0–20 mA or 0–10 VDC or PT100
8 AI2 Analog Input 2 0–20 mA or 0–10 VDC
7 AI1 Analog Input 1 0–20 mA or 0–10 VDC or PT100
6 DI2- Digital Input 2
Dry contact type – do not apply power to these inputs
5 DI2+ Digital Input 2
4 DI1- Digital Input 1
3 DI1+ Digital Input 1
2 COM Relay output common Isolated inputs
Rated load: 1 A @ 24 VDC
1 NO Relay output, NO
The analog inputs must be configured for voltage, current or PT100 input.
The digital inputs are of the dry contact type which require no control voltage.
Do not connect power to the digital inputs as this may damage the unit.
The relay output must be supplied from an isolating transformer using a secondary
listed fuse rated at maximum 3.3 A and minimum 30 VDC.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 7 (26)
2.3.2 Power Supply
Connecting power with reverse polarity or using the wrong type of power supply
may damage the equipment. Make sure that the power supply is correctly
connected and of the recommended type.
Fig. 3 Power supply connector
Connect a DC power supply of the recommended type to the +(plus) -(minus) terminals. See
also Technical Data, p. 23.
2.3.3 USB Connector
Fig. 4 USB connector
The USB micro B connector can be used to connect a computer to the unit for local configura-
tion, firmware upgrades and troubleshooting.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 8 (26)
2.3.4 SIM Card (EC350)
Fig. 5 Installing the SIM card
The SIM card must have a mobile data plan and allow text messaging. PIN code security must
be disabled. Additional configuration in Netbiter Argos or in the local web interface is required.
Insert the SIM card carefully and push it firmly downwards until it clicks into place. Observe the
position of the cut-off corner and the contact surfaces.
Make sure that the SIM card does not slip behind the holder.
2.3.5 Antenna Connectors (EC350)
Fig. 6 EC350 antenna connectors
An external 3G/GPRS stub antenna is included with the unit1. Other antennas are available
from your supplier.
A GPS antenna (not included) must be connected to the GPS antenna connector to use the
built-in GPS receiver. The GPS antenna connector also provides power for active GPS
antennas.
Netbiter EC300 Series User Manual SCM-1202-012 2.2
1. Antenna not included when sold in the U.S.

Installation 9 (26)
2.3.6 RS-485 Serial Interface (3-pin)
Fig. 7 RS-485 connector
The RS-485 interface can be used for multiple Modbus RTU devices.
RS-485 connector pin layout
Pin Function
A RS-485 A line
B RS-485 B line
COM RS-485 common
2.3.7 RS-232 Serial Interface (3-pin)
Fig. 8 RS-232 connector
The RS-232 interface can be used for a single Modbus RTU device.
RS-232 connector pin layout
Pin Function
Rx Receive (input)
Tx Transmit (output)
GND Signal ground
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 10 (26)
2.3.8 Ethernet Ports (RJ45)
Fig. 9 Ethernet Ports
WAN Use for Internet and Netbiter Argos
LAN Use for EtherNet/IP, Modbus TCP and Remote Access
Never connect the LAN and WAN ports to the same logical network.
RJ45 pin layout
Pin Function
1 TD+
2 TD-
3 RD+
4, 5, 7, 8 (reserved)
6 RD-
Ethernet Port LED
Indication Function
Off No traffic
Orange, flashing Traffic (10 Mbit/s)
Green, flashing Traffic (100 Mbit/s)
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 11 (26)
2.4 LED Indicators
All indicators will light up while the unit is starting up. When the startup sequence has completed
they will indicate system status.
In case of an Uplink/WAN error, check the network and firewall settings. If using DHCP, also
check that the DHCP server is active.
Fig. 10 EC350 LED indicators
LED Indication Meaning
Modem (EC350)
Off Modem disabled
Red Modem failure
Red, flashing SIM card failure
Orange PIN code enabled on SIM card
Orange, flashing APN (Access Point Name) not set
Green, flashing Searching for mobile network
Green Connected to mobile network
CAN
Off Port disabled
Red Port failure
Green Port enabled
RS232/RS485
Off Port disabled
Red Port failure
Green Port enabled
Uplink/WAN
Off No link
Red No valid IP address
Red, flashing No connection to Netbiter Argos
Green Connected to Netbiter Argos
Gateway
Off No power or initializing
Red Hardware failure
Red, flashing Application failure
Green, flashing Firmware update in progress
Green Unit is operational
Power Off No power
Green Unit has power
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 12 (26)
2.5 MODE Button
Fig. 11 Mode button
Factory Reset
Keep the MODE button pressed while powering on to reset the unit to the factory default
settings.
Mobile Signal Strength Indication (EC350)
Fig. 12
Press and release the MODE button to make the top 5 LED indicators indicate mobile signal
strength for 60 seconds.
LED indication Meaning
2–5 green LEDs, flashing Good to optimum signal
1 green LED, flashing Acceptable signal
1 orange LED, flashing Poor signal
1 red LED, flashing No signal or unknown signal
If mobile signal strength is poor
• Make sure that the antenna is correctly installed and of the correct type.
• The antenna should normally be vertically oriented. Signal quality may in some cases be
improved by changing the antenna angle.
• Try moving the unit to another position, or use an external antenna.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Installation 13 (26)
2.6 Wiring Examples
Fig. 13 Analog Input – Voltage Sensor
Fig. 14 Analog Input – 2-wire Current Sensor
Fig. 15 Analog Input – 3-wire Current Sensor
Fig. 16 Analog Input – 4-wire Current Sensor
Fig. 17 Analog Input – Temperature Sensor
Fig. 18 Digital Input
Do not connect a power source to the digital inputs as this may damage the unit.
Fig. 19 Relay Output
The relay output must be supplied from an isolated transformer using a secondary
listed fuse rated at maximum 3.3 A and minimum 30 VDC.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Local Configuration 14 (26)
3 Local Configuration
Local configuration is normally not required and should only be carried out when
necessary. Please read the instructions below carefully.
The built-in web interface is primarily intended for informational purposes and troubleshooting.
Netbiter Argos is always the preferred way of configuring the gateway. The only configuration
changes that should be made using the local web interface are:
• Proxy settings (if required)
• Modem/Ethernet connection mode (EC350 only)
• Firmware updates
3.1 Connecting via USB
Connect a USB Micro B cable between the computer and the USB port on the Netbiter.
The USB device driver will automatically load and create a virtual network interface on the com-
puter with an IP address in the range 169.254.200.xxx. The local web interface of the gateway
can then be accessed by entering the IP address 169.254.200.200 in a web browser.
Fig. 20 Network Connections
3.2 Connecting via Ethernet
Connect an Ethernet cable between the computer and the LAN port on the Netbiter.
The default IP address of the LAN port interface is 10.200.1.1. The connecting computer must
have an IP address within the same subnet (10.200.1.xxx). The LAN IP address can be
changed after logging in or from Netbiter Argos when the Netbiter is online.
3.3 Login
Enter the IP address of the gateway in a web browser to log in. The default user name is admin,
and the password is the activation code that was supplied with the unit.
Fig. 21 Local configuration login
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Local Configuration 15 (26)
3.4 Status
The Status tabs present an overview of the configuration as well as detailed information about
the current connections, which can be used when troubleshooting and when contacting Netbiter
support.
Fig. 22 Status – Overview
3.4.1 Status – WAN/LAN
Fig. 23 WAN/LAN Status
The WAN and LAN status tabs present the current IP settings of the Ethernet interfaces.
3.4.2 Status – Uplink
Fig. 24 Uplink Status
The Uplink status tab shows the default connection type (modem or Ethernet) and the default
gateway and DNS servers for the uplink connection.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Local Configuration 16 (26)
3.4.3 Status – Modem
Fig. 25 Modem Status
The Modem status tab presents basic and advanced information about the current mobile net-
work connection.
Basic information
Data Connection Indicates if data connection is established
Signal strength The strength of the mobile signal
Network Mobile network operator
Network type Mobile network type (3G or GSM)
Service state Network registration status
Advanced information
Cellular network type Network type details
Signal quality (3G only) Signal-to-noise ratio of the 3G signal. 0 = -24 dB, 49 = 0 dB
APN Access Point Name
IP, Netmask IP settings for the modem connection
Tower MCC Country code of the connected base station
Tower MNC Network code of the connected base station
Tower Location Area Code Area code of the connected base station
Tower Cell ID Cell ID of the connected base station
Modem temperature The temperature of the modem in °C
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Local Configuration 17 (26)
3.5 Network Settings – WAN
Fig. 26 WAN settings
The WAN interface should be enabled when connecting to Netbiter Argos via Ethernet.
When DHCP is enabled the unit will automatically receive the settings for IP address, subnet
mask, default gateway, and DNS. Contact your network administrator if in doubt.
3.5.1 Proxy Settings
Fig. 27 Proxy settings
If you are connecting to the Internet via a proxy, check Enable Proxy settings, select the
Proxy protocol and fill in the IP address and port number for the proxy server. If the proxy re-
quires authentication, check Use Proxy authentication and fill in the username and password.
The proxy password must not contain blank spaces.
Click on Save settings when finished.
For information about supported proxy types, see Technical Data, p. 23.
Netbiter EC300 Series User Manual SCM-1202-012 2.2

Local Configuration 18 (26)
3.6 Network Settings – LAN
The LAN interface must be enabled when using EtherNet/IP or Modbus TCP applications and
when using the Netbiter Remote Access service.
These settings can also be made in Netbiter Argos. See the Netbiter Argos documentation.
Fig. 28 LAN settings
To avoid potential address conflicts when setting a static IP address and netmask for the LAN
port, use only the address spaces that are reserved for private networks:
• 10.0.0.1 – 10.255.255.254
• 172.16.0.1 – 172.31.255.254
• 192.168.0.1 – 192.168.255.254
Do not connect the LAN and WAN ports to the same logical network.
Click on Save settings when finished.
Netbiter EC300 Series User Manual SCM-1202-012 2.2