HMS Anybus AWB5121 User guide
Anybus®Industrial WLAN/LTE Router
STARTUP GUIDE
SP2557 1.11 en-US ENGLISH
Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial
Networks of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims
any responsibility or liability for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous
product development. The information in this document shall therefore not be construed as a
commitment on the part of HMS Industrial Networks and is subject to change without notice. HMS
Industrial Networks makes no commitment to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are
only intended to help improve understanding of the functionality and handling of the product. In view of
the wide range of possible applications of the product, and because of the many variables and
requirements associated with any particular implementation, HMS Industrial Networks cannot assume
responsibility or liability for actual use based on the data, examples or illustrations included in this
document nor for any damages incurred during installation of the product. Those responsible for the use
of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in
their specific application and that the application meets all performance and safety requirements
including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from
the use of undocumented features or functional side effects found outside the documented scope of the
product. The effects caused by any direct or indirect use of such aspects of the product are undefined
and may include e.g. compatibility issues and stability issues.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Table of Contents Page
1 Preface ..................................................................... 3
1.1 About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Safety ...................................................................... 5
2.1 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Preparation ................................................................ 6
3.1 Package Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Installation................................................................. 7
4.1 Installing Cellular SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 Wall Mounting Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 DIN Rail Mounting Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.4 Connecting Ground Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.5 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6 Installing Terminal Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7 Connecting Digital Output Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8 Connecting Power Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9 Connecting to Ethernet Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.10 Connecting Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Configuration .............................................................18
5.1 Before You Begin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Web Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.3 Configure the Country/Region Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.4 USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.5 Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
6 Verify Operation..........................................................22
7 Technical Data ............................................................24
7.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Preface 3 (26)
1 Preface
1.1 About This Document
This manual describes how to install Anybus Industrial WLAN Router/
Anybus Industrial LTE Router and set up a basic configuration.
For additional documentation and software downloads, FAQs, troubleshooting
guides and technical support, please visit www.anybus.com/support.
1.2 Document Conventions
The following conventions are used to indicate safety information and other
important content in this document:
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
AVERTISSEMENT
Instruction à suivre pour éviter tout risque de décès ou de blessure grave.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Attention
Instruction à suivre pour éviter tout risque de blessure.
Instruction that must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Safety 5 (26)
2 Safety
2.1 Intended Use
The intended use of this equipment is as a communication interface and
gateway. The equipment receives and transmits data on various physical levels
and connection types.
If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
2.2 General Safety
Caution
Ensure that the power supply is turned off before connecting it to the
equipment.
Attention
Assurez-vous que l’alimentation électrique est coupée avant de la
brancher sur l’équipement.
Connecting power with reverse polarity or using the wrong type of power
supply may damage the equipment. Make sure that the power supply is
connected correctly and of the recommended type.
This equipment contains parts that can be damaged by electrostatic
discharge (ESD). Use ESD prevention measures to avoid damage.
To avoid system damage, the equipment should be connected to ground.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Installation 7 (26)
4 Installation
4.1 Installing Cellular SIM Card
Applicable for the LTE router.
Install a SIM card in the router to connect it to a cellular data network.
Ensure that the SIM card is installed correctly to avoid damage to the SIM
card or the router.
Procedure
1. Loosen the screw locking the SIM card cover, located at the back of the
router, and remove the cover.
Installing SIM 1:
2. Grab hold of the SIM card tray and pull straight out.
3. Place a SIM card in the SIM card tray, following the mechanical print out of
the tray.
4. Place the SIM card tray with the pinhole facing in the right direction and
carefully re-insert the tray.
Installing SIM 2:
5. To use dual SIM cards, repeat step 2 to 4.
6. Remount the SIM card cover and fasten the screw.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Installation 11 (26)
4.4 Connecting Ground Screw
To avoid system damage, the equipment should be connected to ground.
Procedure
1. Establish a direct connection between the ground screw and the grounding
surface prior to connecting devices.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Installation 14 (26)
4.7 Connecting Digital Output Wires
Before You Begin
The relay output are used to detect user-configured events.
When a user-configured event is triggered, the two wires attached to the DO,
fault contacts, form a close circuit.
The fault circuit remains opened until a user-configured event occur.
Procedure
Connect the Digital Output (DO):
1. Insert the wires into the 2 pin DO contact on the 4 pin terminal block.
2. Tighten the wire-clamp screws.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Installation 15 (26)
4.8 Connecting Power Wires
Caution
Ensure that the power supply is turned off before connecting it to the
equipment.
Attention
Assurez-vous que l’alimentation électrique est coupée avant de la
brancher sur l’équipement.
Use a power supply of 8-32 VDC to power the router.
Max power consumption: 11.2 W.
The relay contact supports 0.5 A current, 24 VDC.
Procedure
Connect the router to power:
1. Attach the terminal block connector to the router.
2. Insert the positive and negative wires into the V+ and V- contact on the
terminal block connector.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Installation 17 (26)
4.10 Connecting Antennas
Fig. 1 Antenna connectors
Placement of the antennas
Router Model Placement Type
Anybus Industrial WLAN
Router
A WLAN 1
B WLAN 2
Anybus Industrial LTE
Router
C GPS
GNSS
DCellular 1
LTE-Main
ECellular 2
LTE-Aux
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Configuration 18 (26)
5 Configuration
5.1 Before You Begin Configuration
The router is configured through web management.
The router default IP address is http://192.168.10.1/.
The default router login user name and password is admin.
5.2 Web Management
Prepare for configuring the router settings via the web management interface.
Before You Begin
►To link your computer with the router, make sure that the IP address of the
computer is located in the same subnet as the router default IP address.
Procedure
Access the web management interface:
1. In your browser, type http://IP address and press Enter.
→ The web-based management interface login screen appears.
2. In the login screen, enter user name and password.
3. Click OK.
→ The web-based management interface welcome page appears.
To Do Next
►Configure the router.
Follow the instructions in the user manual.
Anybus®Industrial WLAN/LTE Router Startup Guide SP2557 1.11 en-US
Other manuals for Anybus AWB5121
1
This manual suits for next models
1
Table of contents
Other HMS Network Router manuals
HMS
HMS Anybus AWB5121 User manual
HMS
HMS eWON Flexy User manual
HMS
HMS Anybus User manual
HMS
HMS Intesis INMBSRTR0320000 Assembly instructions
HMS
HMS Anybus User manual
HMS
HMS eWON Flexy 205 User manual
HMS
HMS Intesis INBACRTR0320000 Assembly instructions
HMS
HMS eWON Flexy 205 User manual
HMS
HMS Anybus User manual
HMS
HMS Anybus User manual
