HMS Anybus AWB4005 User guide

Anybus®PoE Injector
100–240 VAC
STARTUP GUIDE
SP2384 1.3 en-US ENGLISH

Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial
Networks of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims
any responsibility or liability for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous
product development. The information in this document shall therefore not be construed as a
commitment on the part of HMS Industrial Networks and is subject to change without notice. HMS
Industrial Networks makes no commitment to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are
only intended to help improve understanding of the functionality and handling of the product. In view of
the wide range of possible applications of the product, and because of the many variables and
requirements associated with any particular implementation, HMS Industrial Networks cannot assume
responsibility or liability for actual use based on the data, examples or illustrations included in this
document nor for any damages incurred during installation of the product. Those responsible for the use
of the product must acquire sufficient knowledge in order to ensure that the product is used correctly in
their specific application and that the application meets all performance and safety requirements
including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from
the use of undocumented features or functional side effects found outside the documented scope of the
product. The effects caused by any direct or indirect use of such aspects of the product are undefined
and may include e.g. compatibility issues and stability issues.
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

About This Document 3 (8)
1 About This Document
This document describes how to install Anybus PoE Injector 100–240 VAC.
For additional documentation and technical support regarding this product,
please visit www.anybus.com/support.
1.1 Document Conventions
The following conventions are used to indicate safety information and other
important content in this document:
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Instruction that must be followed to avoid a risk of reduced functionality
and/or damage to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

Safety 4 (8)
2 Safety
2.1 General Safety Instructions
WARNING
Electrical shock hazard. Do not try to open or disassemble the device.
Caution
Hot surfaces. Use a dry cloth for cleaning.
Caution
Risk of overheating. Do not block the air ventilation openings.
Caution
No user servicable parts inside. Return unit to manufacturer for service.
The equipment is of open type and must be installed in a suitable
enlosure. Ambient temperature must not exceed 70 °C.
2.2 Intended Use
The intended use of this equipment is to provide DC power over Ethernet cables.
If this equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

Description 5 (8)
3 Description
Anybus PoE Injector 100–240 VAC is a dual port 802.3af/at compliant Power
over Ethernet injector with Midspan Intelligent Detection.
The PoE injector will not turn on power until it detects a valid PoE signature
from the devices attached downstream on the Ethernet cable. This protects
non-compliant equipment against damage.
Anybus PoE Injector 100–240 VAC will not function with equipment that is not
fully compliant with the IEEE 802.3af/at PoE standards.
4 Installation
Fig. 1 Dimensions
All measurements are in mm.
Minimum installation clearance from ventilation openings: 100 mm
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

Installation 6 (8)
4.1 Connectors
Fig. 2 RJ45 Ethernet connectors
RJ45 pinning
Pin Name IN (data only) OUT (data + power)
1 Rx+ Data Receive Data Receive
2 Rx- Data Receive Data Receive
3 Tx+ Data Transmit Data Transmit
4-Vdc_return(+) (not connected) Feeding power(+)
5-Vdc_return(+) (not connected) Feeding power(+)
6 Tx- Data Transmit Data Transmit
7-Vdc (not connected) Feeding power(-)
8-Vdc (not connected) Feeding power(-)
Do not connect pin 7 or pin 8 to ground.
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

Appendix A: Technical Data 7 (8)
A Technical Data
A.1 Technical Specifications
Order code AWB4005-B
PoE standard IEEE 802.3at/802.3af
Ethernet IN 1 x RJ45 (Data, 10/100/1000 Base-T(x))
For UL compliance use +105 °C rated cables
Ethernet OUT 1 x RJ45 (Data and power, 10/100/1000 Base-T(x))
For UL compliance use +105 °C rated cables
Input voltage 100–240 VAC
For UL compliance use a 20 A no-fuse breaker and
minimum 18 AWG, +105 °C, ELBZ rated power cable
Output voltage 56 V / 630 mA @ 35 W
LED power indicator —
LED PoE indicators 1 x LED (power, error)
Short circuit protection Yes
Overload protection Yes
High voltage protection Yes
Mounting Wall mount with screws
Weight 210 g
Protection class IP21
Storage temperature -40 to +85 °C
Operating temperature -25 to +60 °C
Housing Plastic (PC)
Dimensions W×H×D 75 x 125 x 38
Certifications See datasheet
Disposal and recycling
You must dispose of this product properly according to local laws
and regulations. Because this product contains electronic
components, it must be disposed of separately from household
waste. When this product reaches its end of life, contact local
authorities to learn about disposal and recycling options, or simply
drop it off at your local HMS office or return it to HMS.
For more information, see www.hms-networks.com.
Anybus®PoE Injector 100–240 VAC Startup Guide SP2384 1.3 en-US

last page
© 2019 HMS Industrial Networks
Box 4126
300 04 Halmstad, Sweden
[email protected] SP2384 1.3 en-US / 2019-07-31 / 14262