HobbyGrower Special Edition Enthusiast User manual

Overall Dimensions
including base (Approx.)
247.4 L • 193 W • 210 H cms
97.5" L • 76" W • 82.6" H
(a)
(a)
ASSEMBLY INSTRUCTIONS
Overall dimensions including base:
247.4 L x 193 W x 210 H cms
97.5" L x 76" W x 82.7" H
ASSEMBLY INSTRUCTIONS
(Internal Dimensions)
Please read these instructions carefully before you start to assemble this greenhouse.
To save time and will ensure proper assembly, follow the step-by-step instructions carefully in order.
New or revised instructions may be available for download at hobbygrower.com, or if you would like
to view a breif general assembly video to gain a basic understanding of how the structure is constructed,
visit http://www.hobbygrower.com, then click on the Assembly tab.
IMPORTANT!!!
%NT3PEC%DITIONV

2
2
4
M56
8
M602
M53
M604
M605
M607
A12
A13
M19
M69
C23
ITEM MM QTY.
CONTENTS
ITEM MM QTY. ITEM MM QTY.
1190mm 46.8” 10
575mm 22.6” 8
1290mm 50.7” 4
062” 6
16mm
M21 6
1
-2-
1
M29
P1
P2
P4
P5
P6
M8
A15
A16
23.6”x23.6” 27
2
059” 10
2
2
550mm 21.6” 2
1290mm 50.7” 2
Door
handle hole
See fig. 49
A11 1100mm 43.3” 2
590mm 23.2” 18
1290mm 50.7” 8
920mm 36.2” 4
P3
600x600mm
23.6”x27.5” 1
23.6”x27.5” 13
3
M9 2
M10
M10A
5
9
600x700mm
600x700mm
A14N 530mm 20.8” 1L
530mm 20.8” 1R
590mm 23.2” 1
1330mm 52.3” 2
550mm 21.6” 1
1290mm 50.7” 1
10
10
062” 48
16mm
12
47.2” 2
1200mm
0.31” 1
8mm
M70
M33
M32
M31
1
1
M603
23.6” 2
600mm
15mm

TOOLS & EQUIPMENT REQUIRED
SAFETY ADVICE
GENERAL ADVICE
CARE & MAINTENANCE
1See next page for complete list of parts
• Do not attempt to assemble the greenhouse in windy
or wet conditions.
• Take special care not to touch overhead power
cables with aluminum profiles.
• Ensure that there are no buried pipes or cable in the
ground before inserting the ground stakes.
• Always wear shoes and saftey goggles during assembly.
• We strongly recommend the use of work glove during
assembly as aluminum profiles and steel bases
components may have sharp edges.
• Dispose of plastic bags and protective poly film covers
safely - keep them out of reach of small children.
• The greenhouse must be positioned and anchored on
a flat, level surface.
• Do not lean on or push against the greenhouse
during construction.
• Keep children away from assembly area - the
aluminum profiles may have sharp edges.
• Do not position your greenhouse in an area exposed
to heavy wind.
• Do not attempt to assemble the greenhouse if your
are tired, have taken drugs or alcohol or if you are
prone to dizzy spells.
• If you use a step ladder, carefully follow the
manufacturer's instructions.
• Hot items such as recently used grills, blowtorches,
etc. must not be stored in the greenhouse.
• Before beginning the assembly process, confirm
that all necessary parts have been included in the
package. It is advisable to lay the parts out in an
orderly fashion according to the part numbers so that
parts can be easily identified during the assembly
process. If parts are missing, contact Palram Americas
Hort Division at [phone].
• This is a multi-part assembly. Average assembly time
is between 4 to 6 hours from start to finish, however, it
may take longer. Do not begin assembly if heavy
winds or rain are expected within 12 hours.
• Choose a sunny level location for your greenhouse,
away from overhanging trees.
• You can opt to use the base brackets supplied to
anchor your greenhouse to a concrete floor, or you
can use the base supplied base kit . If you intend to
anchor your greenhouse directly to concrete, you must
purchase separately concrete anchor screws. The
area required for the greenhouse is 104.5" (266cm)
length x 83" (212cm) width.
• It is advisable to use lubricant to ease the connection
between aluminum profiles and panel (a mild soap and
water solution in a pump-spary bottle is useful for this).
• Note that the door is permanently hinged on the right
hand side and therefore opens out and to the right.
• We strongly advise that you keep the special poly-film
protective covers on the side panels and the first row
of roof panels until that greenhouse is fully
assembled. You should however remove the poly-film
prior to installing the very top roof panels. You should
also remove the rest of the protective poly film
immediatly after assembly.
• Keep roof clear of snow and leaves.
• Use mild soap and water and a soft cloth to wash
greenhouse glazing panels. Rinse with cold water.
• Do not use acetone, abrassive cleaners or sponges, or
other amonia-based cleaners to clean the clear panels.
• Some chemicals and cleaners can be agressive to the
clear panels, which are made of polycarbonate. For a
complete list of chemical compatibility, visit:
http://www.spscorp.com/compatibility
• To purchase replacement parts, contact customer
service at Palram Americas at [phone].
• 100% "Silicone" Sealant
(compatible w/polycarbonate)
• Tape measure
• Work gloves
• Plastic or rubber mallet
• Crosshead Screwdriver (a.ka.
"Philips screwdriver")
* Screw-gun is suggested
• Scissors
• 10mm Wrench
• Lubricant (mild soap & water)
• Step ladder
• Level
• Large Hammer (for anchor stakes)
• 5/64" Drill bit (or similar diameter nail)
SYMBOLS USED IN THIS GUIDE
(a)
M605
1Indicates new
installation step. Indicates item or part number to be used;
references list on pg. 2.
Lower case letters within
parenthesis indicate a sub-
installation step. Complete
a, b, c, etc. in order. !Important safety
warning, caution,
or time-saving tip.

click
1
M607
M607
M605
M605 (b)
M603
M604
(c)
(c)
M604
(d)
M29
M603
2
(a) M605
!!!!
3
M605
M29
-3-
A
B
C
DAC = BD
M603
M606
(e)
M601
M601
M603
M603
M602
M602
M606

M56
M56
M56
M56
4
M56
5
(c)
(b) (c)
(a)
6M53
M29
-4-

7
8(a)
(a)
(a)
A11
36.2”
A11
36.2”
Front
Side
A11
36.2”
M10A
A11
36.2”
A11
36.2”
(a)
(c)
(b)
(a)
Back
Side
(d)
A11
50.7”
A11
43.3”
(a)
M10A
(a)
A11
43.3”
A11
43.3”
A11
50.7”
A11
50.7”
M10A
(a)
(c)
(c)
-5-
Back
Side
Front
Side
(d)
0.07”
(b)
(b)
0.07”
0.07”

P1
P1
10
-6-
9
Back
Side
Front
Side
Back
Side
Front
Side P1
0.07”
0.07”

A13
50.7”
P1
P1
P1
12
(c)
(a) (b)
P3 (c)
P1
11
A13
50.7”
P1 P1
10cm
-7-
P1
P1
P1
(a) P3

14
(b)
(a)
P1
P1
P1
P3
P3
P1
P3
-8-
13
P1 P1
P1
P3
A11
50.7”
A11
50.7”
A11
50.7”
A11
50.7”
(b)
(a)
Slide profile A11/50.7” to connect the panels.
Slide one more rectangular panel P3 onto the profile ensuring it has the interlocking slot at its bottom
(a), (b).

16
(a)
P1
P1
P1
P3
P3
(b)
(b)
P1
P3
P3
P1
15
-9-
P3
P3
P1
P1 P1
P1
A11
50.7” A11
50.7”
Slide another profile A11/50.7” to connect the panels, and another
panel P1.
Slide one more rectangular panel P3 onto the profile ensuring it has the interlocking slot at its bottom
(a), (b).

P1
(a)
(b)
A11
50.7”
P1
18
17
-10-
P1 P1
P3
P3
(b)
P3
P1
P1
A11
50.7”
P1
P1 P1
P3
P3
P3
P1
P3
Slide another profile A11/50.7” to connect the panels, and another
panel P1.
Slide one more rectangular panel P3 onto the profile ensuring it has the interlocking slot at its bottom
(a), (b).
(a)
(b)

-11 -
19A
19B
19C
AA
B
C
C
19 P6
0.31”
0.55”
0.31” 0.31”
X 3

21
20
-12-
(a)
P3
P1
P1
P1 P1
P3
P3
P3
P1
P3
P3
P1
P1 P1
P3
P3
P3
P1
P3 A13
50.7”
A13
50.7”
P1 P1
0.39”
(b)
P6
P6
0.39”
Slide panel P1from left to right and the vent panel P6 from right to left.
Slide another corner profile A13-50.7” but leaving approximately 0.39”
protruding at the top.
21

P6
P6
22
P3
P1
P1 P1
P3
P3
P3
P1
(b)
BACK
A14
52.3”
A14
52.3”
A14 52.3”
-13-
23 A14
Slide one more rectangular panel P3 onto the profileA13/50.7”
Slide a vertical profile A14/52.3” to connect the panels on the back wall.

P6
P6
P3
P3
P1
(a)
(b) A14
23.2”
A14
23.2”
24
P1
P1
P1
P3 P3
P3
BACK
P3
25
-14-
P3
P1
P3
P6
Slide one more rectangular panel P3 onto the profileA14/52.3”.
25Fit horizontal profile A14/23.2” as
shown.

26
-15-
P6
P3
P3
P1
P1 P1
P1
P4
27
P1 P6
A14
52.3”
P3
P3
P4
Slide on a top panel P4.
Slide another vertical profile A14/52.3” to connect the panels.

28
-16-
P3
P6
(a)
P3
P3
P1
P1
P4
(b)
(c) P1
P1
29
P6
A13
50.7”
P3
P3
P1
P4
P1
P1
A13
50.7”
P1 P1
0.39”
Slide another two panel P1.
Slide another corner profile A13-50.7” leaving approximately
0.39” protruding at the top.

P6
(b)
P3
P3
P1
P1 P1
P4
P1
P1
(a)
A11
50.7”
30
31
-17-
P1
P3
P6
P3
P3
P4
P1
P1
P3
Slide one more rectangular panel P3 onto the profileA13/50.7”
Slide another profile A11/50.7” to connect the panels.

P1
P3
P6
P1
P3
P6
32
(b) P3
P3
P1
P1 P1
P3
P3
P3
P1
P4
P1
P1
(a)
(d)
(c)
(b)P1
P1
P3
P3
A11
50.7”
-18-
P3
P3
P1
P1 P1
P3
P3
P3
P1
P4
P1
(c)
(d)
A11
50.7”
P1
P1
P3
P3
(a)
(b)
P1
33
Slide one more rectangular panel P3 onto the profileA11/50.7”
and another profile A11/50.7” to connect the panels.
Slide one more profile A11/50.7” and one panel P1.

35
P1
(a)
(b)
-19-
P1 P1
0.39”
P6
P3
P3
P1
P1
P1 P1
P3
P3
P3
P1
P4
P1
(c)
P3
P1
P1
P3
P3
(a)
(b)
P3
P3
M31
M31
P1
(c)
34
A13
50.7”
Slide part number M31 onto the profile
A11/36.2” from left to right (see the
diagram).
Slide one more panel P1 (a) and another corner profile A13/50.7” (b).