Holmes HT38R User manual

PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
Owner’s Guide
HT38R/HT38RB2
HTF3610AR
Remote Control
Tower Fan

PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
return to an authorized service facility for
examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock
and injury to persons, do not use in window.
19. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement
fuse blows, a short circuit may be present and the
product should be discarded or returned to an
authorized service facility for examination and/or
repair.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.

FEATURES - OPERATIONS
ASSEMBLY INSTRUCTIONS
Assembly Time: 10-15 minutes.
Tools Required: Phillips head screw driver.
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROM
THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN.
LOCATE THE BELOW PARTS FROM THE BOX TO PREPARE
FOR ASSEMBLY:
• Fan housing
• 2 pedestal halves
• 2 base halves
• 8 M4x10mm screws (4 pcs for pedestal assembly
and 4 pcs for base assembly)
• Cord clip with 2 M4x12mm screws (affixed
underneath the base inside the package box)
• Remote Control (placed in a plastic bag inside the
package box)
Follow the steps below in order to assemble the fan
pedestal and base before operating your fan:
1. To assemble the pedestal, simply snap the 2 pedestal
halves together (Fig. 1).
2. Pull the power cord through the assembled pedestal,
making sure the wider end of the pedestal is facing
towards the fan housing (Fig. 2).
3. Align marking “A”, located at the bottom of the fan
housing, with marking “A” on the top end of the
pedestal. Insert the alignment post from the pedestal
into the alignment hole on fan housing for proper
alignment (Fig. 3).
4. Use 4 screws (M4x10mm) provided to attach the
assembled pedestal to the bottom of the fan housing.
Secure the screws with a screwdriver (Fig. 4).
5. Snap the 2 base halves together by sliding the posts
of one base half into the slots of the second base half
(Fig. 5).
Fig. 1
Fig. 2
Fig. 5
A
Fig. 3 Alignment Hole "A"
Alignment Post "A"
Fig. 4
4 screws (M4x10mm)

6. Pull the power cord through the center hole of the
assembled base (Fig. 6).
7. Align marking “B”, located at the center hole of the
assembled base, with marking “B” at the bottom end
of the pedestal. Insert the alignment post from the
pedestal into the alignment hole on base for proper
alignment (Fig. 7).
8. Use 4 screws (M4x10mm) provided to attach the
assembled base to the pedestal. Secure the screws
with a screwdriver (Fig. 8).
9. Wind the power cord underneath the base. Loosen
the cord clip and place cord inside the clip. Secure the
cord clip onto the base bottom with the 2 screws
(M4x12mm) provided (Fig. 9).
10. Turn fan right side up and place on a dry and level
surface before operating.
OPERATING INSTRUCTIONS (SEE FIG.
10, 11)
A. Power/Speed Settings
Press = On, I, II, III, Off
B. Timer Control
Press = Turns Off in 1, 2, 4, 8 hours
C. Oscillation Control
Press = Oscillation On, Off
D. Natural Breeze, Sleep Breeze Modes
Press = Natural Breeze, Sleep Breeze
Natural Breeze Mode will cycle through the fan
speed settings randomly.
Sleep Breeze Mode will cycle through the fan
speed settings in order.
FEATURES - OPERATIONS
Fig. 6
Fig. 10 Control Panel
AD
B
C
Fig. 9
Fig. 8
B
B
Fig. 7

FEATURES - OPERATIONS
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. The product generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that the interference will not occur in a
particular installation. If the product does cause harmful
interference to radio or television reception, which can be
determined by turning the product on or off, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the
receiver.
• Connect the product into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
• Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
REMOTE CONTROL
This fan includes a remote control requiring two (2) AAA
batteries, 1.5V (not included).
Battery Replacement
a) Remove battery cover from remote control.
b) Remove old batteries from the remote control.
c) Insert two new batteries, pressing them firmly into
their slot.
d) Replace the battery cover.
NOTES:
• Replace all batteries of a set at the same time.
• Being careful not to bend or damage the contact
spring, clean the battery contacts and devices'
contacts prior to installing the batteries.
• Remove the batteries from the equipment when it is
not being used for an extended period of time.
• Remove the used batteries promptly.
• Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc), or rechargeable
batteries.
• Do not discard used batteries into household trash
containers. Contact your local government for
disposal or recycling practices in your area.
BT16-UK 8/0 5
Fig. 11 Remote Control
A
B
D
C

CLEANING/MAINTENANCE
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your Tower Fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
visit our website at www.holmesproducts.com for
information on how to order a new fuse. Follow the below
instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover down towards the prongs.
Note: Ensure that fuse
cover is completely open
before attempting to
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the metal
ends of the fuse
(see Fig. 12).
4. Place plug on a solid, flat surface. Insert new 5 Amp,
125 Volt fuse into fuse compartment and use a small
screwdriver to secure the metal ends of the fuse into
the compartment.
Caution: Risk of fire. Replace fuse only with 5 Amp,
125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the
fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
FAN CLEANING:
• Always unplug the fan before cleaning.
• Clean the fan with a soft cloth moistened with a mild
soap solution.
• Do not allow water to drip on or into the fan motor
housing.
• Do not use any of the following as a cleaner:
gasoline, thinner, benzene.
• You may also clean the front grill of the fan by
lightly running a vacuum cleaner nozzle over the grill
surface.
FAN STORAGE
In the off-season, it is important to keep your fan in a
safe, dry location.
• We recommend using the original (or appropriately
sized) box.
• Please remember to protect the fan from dust or
moisture.
If you have any questions regarding your product or
would like to learn more about other Holmes®
products, please visit our website at
www.holmesproducts.com. For responsible disposal of
this product, please go to http://earth911.com/.
Fuse cover
Fig. 12
Metal ends
Fuse

WARRANTY INFORMATION
3 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of three years from
the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair
or replace this product or any component of the product found to be defective during the warranty period. Replacement
will be made with a new or remanufactured product or component. If the product is no longer available, replacement
may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair
or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or
retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this
warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair
or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts
of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a
particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the
product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract,
fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any questions regarding this warranty or would like to obtain warranty service, please visit our website at
www.holmesproducts.com.
In Canada
If you have any questions regarding this warranty or would like to obtain warranty service, please visit our website at
www.holmesproducts.com.

WARRANTY INFORMATION
© 2014 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
Printed In China
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located
in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other
problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO NOT
RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.