IMPORTANT SAFETY INSTRUCTIONS
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all parts
properly in place.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
19. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20. This product employs overload protection (fuse).
A blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
should be discarded or contact customer service.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on or
taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
9. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
CLEANING / MAINTENANCE
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for
your fan.
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows,
please visit our website at www.getholmesfans.com for
information on how to order a new fuse.
REPLACING THE FUSE
1. Unplug your fan.
Grasp plug and remove from the receptacle or other
outlet device.
NOTE: Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide
the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open
before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to
pry it from the compartment at the metal ends of the
fuse. (See Figure 2)
4. Place plug on a solid,
flat surface. Insert new 5
Amp, 125 Volt fuse into
fuse compartment. Use
a small screwdriver to
secure the metal ends of
the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with 5
Amp, 125 Volt fuse.
5. Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure
the fuse is completely secured in place by pressing on
metal ends of the fuse.
TILT ADJUSTMENT
VERTICAL ANGLE ADJUSTMENT
1. To adjust the angle, move the fan head to the desired
position.
2. Firmly tighten the Tilt Adjustment Knob (D) to keep
the fan head in place.
ASSEMBLY
Your Table Fan comes completely assembled and is ready
for use.
OPERATING INSTRUCTIONS
1. Set fan on a dry, level, and stable surface.
2. Make sure the Selector Switch is in the OFF (O)
position. Plug cord into any standard 120 volt AC
outlet.
3. Press the selector switch to choose the desired setting:
O (OFF)
I (LO)
II (HI)
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
Figure 2 Fuse
Fuse cover
Metal ends
A. Fan Head
B. Motor Housing
(not visible)
C. Fan Base
D. Tilt Ajustment
Knob
E. Speed Selector
Switch (not visible)
Figure 1
E
B
D
C
A
ASSEMBLY, PARTS
AND OPERATING INSTRUCTIONS
FAN CLEANING
• Always unplug the fan before cleaning.
• Wipe the fan grill, housing and base with a soft,
damp cloth.
• Do not allow water to drip on or into the fan
housing.
• Use only a soft cloth moistened with a mild soap
solution.
• Do not use harsh chemicals such as gasoline,
thinner or benzene as a cleaner.
• Do not attempt to remove the fan blade.
• Use CAUTION around the motor housing area.
Do not allow the motor or other electrical
components to be exposed to water.
FAN STORAGE
• Store the fan in a clean, dry location between seasons
or when not in use for an extended period.
• Keep the fan head protected from dirt and dust during
storage.
CAUTION: Risk of fire. Do not replace the attachment
plug. It contains a safety device (fuse) that should not
be removed. Discard product if the attachment plug is
damaged.
If you have any questions regarding your product
or would like to learn more about other Holmes®
products, please visit our website at
www.getholmesfans.com or call customer service:
1-866-769-3166 (8:30 am - 5:00 pm E.S.T.) or send
regarding recycling and proper disposal of this
product, please contact your local waste
management facility.
