HOLOVISION 400-A-VIO User manual

Manual Type 6.5.0.9-RF
xxx
with Essex “ASCII” Keypad
For Models
400-A-VIO 401-A-VIO
403-A-VIO 404-A-VIO
410-A-VIO 411-A-VIO
Specifications
INSTALLATI N
INSTRUCTI NS
501 E. Goetz Ave.
Santa Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax [phone]
H L VISI N
Access Control
Essex K1-26I Keypad field configurable to ASCII,
Wiegand and others.
400 Series ‘’A’’ Junction Board
Not Used
Not Used
Connect tamper switch to alarm (optional)
Not Used
Bit arity Mode
Inverted Serial
Ground
Normal Serial
Communication
Holovision VIO is a SI enabled intercom module
developed specifically with the custom integrator in
mind. It works with Crestron RAVA/SI and most SI
enabled VoI phone systems and servers.

age 2 Type 6.5.0.9-RF
ASCII Connection to Crestron or HAI 400
NO COM NC NO COM NC
Red Green LED control Gate Control
Automation System Relays
(Typical of Crestron or HAI)
To gatecontrol
HAI
To Automation System
(see details below)
Crestron
Black to pin 5
White to pin 2
Crestron Serial ort
Z1
----
Z2 Z3 Z4 Z5
GRD 12V Switched
12V AUX
24VAC
- - -
To HAI serial port:
RJ-11 Black = pin 1 White = pin 4 (RJ-11 is 4 pin)
RJ-25 Black = pin 2 White = pin 5 (RJ-25 is 6 pin)
Black
Black to “Grnd”
White
Viewed with ‘’tit’’ up
Black
Green
The red LED is normally on all of the
time. When a valid code is entered, the
relay controlling the LEDs would close,
and the green light would go on
(momentarily). Note, this relay must be
programmed in Crestron or HAI in order
for this to take place.
K1-26I
ASCII Keypad
12vDC
1.5A

VIO Wiring Diagram
age 3 TYPE 6.5.0.9-RF
To Automation System
To Automation System Relay NO & COM
TO GATE
CONTROLLER OR
“REMOTE
TERMINALS” ON
ASCII
CONTROLLER

age 4 TYPE 6.5.0.9-RF
VI RAVA Quick Start
1. lug the device into the network. Device will speak it’s I address.
2. Navigate to device I on a web browser.
3. Under “Configuration” please enter SI ID for the name to be displayed, and enter the extension
of the Main RAVA Touchscreenunder “Input Call ID 0 Default is CALL:CRESTR N”
*Note out of the box the “CALL:CRESTR N” default will ring all touchpanels in the CRESTR N
call group.
4. Configure the Audio setiings. Note:RAVA peration has been designated to “Push to Talk” (PTT)
from Crestron and only this operation will be supported. Although full duplex and half duplex
are an option, these settingdo not perform best in all senarios. As a recommendation you can
experiment for the best audio settings.
AUDI SETTING BEL W ARE NLY A REC MMENDATI N

5. Configure the relay setting under “Inbound Calls”. Configure the powered relay and the dry
contact closure. Choose any 2 to 4 digit combination
Note; By configuring the request to exit feature you can configure for either relay.
6. Once the device has been configured you can initiate the call by pressing the button
age 5 TYPE 6.5.0.9-RF



     

 

 
















      
#          

     















   

  


%&
  !"
"
   
  !##$"# 


'
      
VI (sip) QUICK START
age 6 TYPE 6.5.0.9-RF

 



 
22
age 7 TYPE 6.5.0.9-RF

501 E. Goetz Ave.
Santa Ana, Ca 92707
Ph. 714-434-6904
Fax [phone]
www.eholovision.com