HOLOVISION 400-W-VIK User manual

Red 12+ to Wiegand Controller
Black 12- to Wiegand Controller
Green Data 0 to Wiegand Controller
White Data 1 to Wiegand Controller
Ground/Drain
For Green LED control
For Red LED control
For Site Code odification
Manual Type 6.4.0.5-RF
Viking W-1000 w/C-1000B Controller
and Essex Wiegand Keypad
For Models
400-W-VIK 401-W-VIK
403-W-VIK 404-W-VIK
410-W-VIK 411-W-VIK
Specifications
INSTALLATION
INSTRUCTIONS
501 E. Goetz Ave.
Santa Ana, Ca 92707
www.eholovision.com
h. 714-434-6904
Fax [phone]
HOLOVISION
400 Series “W” Junction Board
13.8 VAC (from C-1000B)
Connect tamper switch to alarm (optional)
Intercom to C1000B (Not polarity senitive)
Access Control
Essex KPT-26TI 26 bit Wiegand Keypad
Communication
Viking W-1000 Doorbox uses “half-duplex”
communication, allowing for high speaker and
microphone volume, witout the possibility of
feedback.

To Remote Input on
Wiegand Controller or to
Gate Contact
House Phones
Incoming CO
Wiring Diagram for Viking W-1000/C-1000B
Page 2 Type 6.4.0.5-RF
To Wiegand Controller
VIKING Model C-1000B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
EARTH GND
PHONE LINE INPUT
LINE OUT TO PHONES
KEYLESS CONTACT
DOOR BOX 1
DOOR BOX POWER
DOOR BOX 2
DOOR STRIKE 1
DOOR STRIKE 2
1 2 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
OFF ON
13.8 VAC
1.25A

Page 3 TY E 6.4.0.5-RF
W-1000 Adjustments and rogramming
In certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom of this is one-way talk path, in which the distant party cannot be
heard over the speaker. A “MIC VOL” adjustment is provided on the doorphone for increasing or decreasing the microphone volume.
Microphone Volume
The “S KR VOL” pot can be adjusted to increase or decrease the speaker volume to the desired level.
Speaker Volume
The maximum number of rings can be adjusted using the DIP switches.
Maximum Number of Rings
ON
1 2
+
+
+
Spkr Vol
ic Vol
ON ON
1 2
Sw 1 Sw 2 ax Rings
OFF OFF 2
ON OFF 3
OFF ON 10
ON ON 30
C-1000B Door Controller rogramming
1 Disconnect the PHONE LINE INPUT.
2 Slide the TALK BATTERY switch to the ON position.
3 ove DIP SWITCH 2 from OFF to ON.
4 Connect a phone to terminals 4 & 5 - LINE OUT TO PHONES.
5 Pick up the phone (you will hear a double beep - indicating that you have accessed the PROGRA ING ODE).
6 You can now Touch Tone program the features listed below. SEE HOLOVISION Programming NOTES.
7 When Finished, hang up and move DIP SWITCH 2 to the OFF position
8 Slide the TALK BATTERY switch back to the OFF position
9 Reconnect line to PHONE LINE OUT
Step Action
The C-1000 controller is factory set to work right out of the box. If customization of
the default settings is required, see the steps listed below. Refer to the C-1000
manual for additional options

HOLOVISION’s rogramming Notes
Doorstrike Activation Time - Generally the default setting of 1/2 sec is fine. The momentary contact can open a motorized gate, or activate the relay on the
“S-12” keypad. For other keypad types this will be changed.
Doorbell Mode (*1)- phones will not ring when doorbell is pushed. This is useful when conventional door chimes are desired. In order to use this feature, the
Auxiliary Contacts must be programmed. (see above)
Custom Ring Mode (*2)- Distinguishes doorbox ring from CO ring when connected to KSU.
CCTV Video Control Mode (*8)- The C-1000B can switch 2 CCTV cameras, displaying the camera at the doorbox which initiates the call. This mode cannot
be used when the “Auxiliary Contacts” are being used.
Disable Special Modes (*0) - Use this command to disable (clear) all special modes programmed.
REFER TO C-1000B ANUAL FOR ORE INFOR ATION ON THESE, AND OTHER ODES OF OPERATION.
`1 Slide the TALK BATTERY switch to the OFF position.
2 ove DIP SWITCH 2 from ON to OFF.
3 Re-connect the PHONE LINE INPUT and LINE OUT TO PHONES.
Return to normal use mode
Step Action
O ERATION OF C-1000B
ANSWER A CALL FROM DOORBOX
When the phones ring, pick up a phone to be connected to the visitor. When the C-1000B controller is used, you will
hear a beep tone when the phone is answered - one beep for doorbox 1, and 2 beeps for doorbox 2.
LACING CO LINE CALLS ON HOLD (CALL WAITING)
If a phone call is in progress, and a door box is activated, a single or double “call waiting “ tone will be heard. To place the call in
progress on hold and speak to the visitor, push #. When you want to return to the original phone call, push #.
ACTIVATING A DOORSTRIKE OR O ENING A GATE
To open the gate, you must first be connected to the doorbox. Push .You will then hear a confirmation tone, and the relay will be
activated for the programmed time. If a call was already in progress, pressing will open the gate, and return the system to the
original phone call.
LATCH / UNLATCH A GATE
To use this feature, you must first be connected to the doorbox.
Latch relay 1 or 2 1
Unlatch relay 1 or 2 0
**
**
**
Page 4 TY E 6.4.0.5-RF