HOLOVISION Viking E-10 User manual

Manual Type 6.5.0.3-RF
Viking E-10 & C-2000B
with Essex “ASCII” Keypad
For Models
400-A-V K(E10) 401-A-V K(E10)
403-A-V K(E10) 404-A-V K(E10)
410-A-V K(E10) 411-A-V K(E10)
Specifications
INSTALLATI N
INSTRUCTI NS
501 E. Goetz Ave.
Santa Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax [phone]
H L VISI N
Access Control
Essex K1-26 Keypad field configurable to ASC ,
Wiegand and others.
C-2000b can open 4 doors
400 Series ‘’A’’ Junction Board
Not Used
12 VDC input (for camera and keypad)
Connect tamper switch to alarm (optional)
ntercom to C-2000B (Not polarity sensitive)
Bit Parity Mode
nverted Serial
Ground
Normal Serial
Communication
Viking E-10 Doorbox uses “half-duplex”
communication, allowing for high speaker and
microphone volume, without the possibility of
feedback.

Page 2 Type 6.5.0.3-RF
ASCII Connection to Crestron or HAI 400
NO COM NC NO COM NC
Red Green LED control Gate Control
Automation System Relays
(Typical of Crestron or HA )
To gatecontrol
HA
To Automation System
(see details below)
Crestron
Black to pin 5
White to pin 2
Crestron Serial Port
Z1
----
Z2 Z3 Z4 Z5
GRD 12V Switched
12V AUX
24VAC
- - -
To HA serial port:
RJ-11 Black = pin 1 White = pin 4 (RJ-11 is 4 pin)
RJ-25 Black = pin 2 White = pin 5 (RJ-25 is 6 pin)
Black
Black to “Grnd”
White
Viewed with ‘’tit’’ up
Black
Green
The red LED is normally on all of the
time. When a valid code is entered, the
relay controlling the LEDs would close,
and the green light would go on
(momentarily). Note, this relay must be
programmed in Crestron or HA in order
for this to take place.
K1-26
ASC Keypad
12vDC
1.5A

ncoming CO
Viking C-2000B Wiring Diagram
Page 3 TYPE 6.5.0.3-RF
VIKINGcModel C-2000B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
EARTH GND
PHONE L NE NPUT L NE OUT TO PHONES
ENTRY PHONE 1
DOOR STR KE 1
ENTRY PHONE 2
DOOR STR KE 2
ENTRY PHONE 3
DOOR STR KE 3
ENTRY PHONE 4
DOOR STR KE 4
DOORBELL SW TCH/AUX NPUT
AUX CONTACT OUTPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
ON
1 2 3 4 5
ANALOG STAT ON NPUT
13.8
VAC
1.25A
TO GATE
CONTROLLER OR “REMOTE
TERM NALS” ON ASC
CONTROLLER
House
Telephones
For Camera
To Automation System
To Automation System Relay NO & COM
12vDC
1.5A
ToDoorPhone#4
T
oDoorPhone#3
T
oDoor Phone#2

Instructions for E-10 and E-40 Doorphones
n certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom of this is one-way talk path, in which the distant party
cannot be heard over the speaker. A “MIC V L” adjustment is provided on the doorphone for increasing or decreasing the microphone volume.
Microphone Volume
D P Position Description
Switch
1 ON Auto Answer - Doorphone answers when incoming call is detected.
2 ON Call Timer - See E-10 manual for a description of this feature. Recommended setting is “ON”. This is the factory default.
3 OFF Programming Mode - E-10 is factory pre-set, and normally does not need re-programming. Refer to E-10 manual
(Viking document which is included) for details
ON ON ON
1 2 3
ON ON ON
1 2 3
+
+
Spkr Vol
Mic Vol
Holovision recommends the default settings on the dip switches. See the E-10 or E-40 manual for more information.
The “SPKR V L” pot can be adjusted to increase or decrease the speaker volume to the desired level.
Speaker Volume
Dip Switch Settings
Doorphone Programming
Page 4 TYPE 6.5.0.3-RF
Instructions for C-2000B Controller
D P Position Description
Switch
1 OFF Auxiliary Contact Mode
1 ON Doorbell Mode- Factory Default
2 OFF Normal Operation Mode- Factory Default
2 ON Security Code Bypass Mode
3 OFF Entry Phone automatic disconnect (CPC) disabled
3 ON Entry Phone automatic disconnect (CPC) enabled- Factory Default
4 OFF Entry Phone busy signal disabled
4 ON Entry Phone busy signal enabled- Factory Default
5 OFF Single Line Ring Through Mode- Factory Default
5 ON Analog Station Dial Through Mode
Dip Switch Settings C-2000B
ON
1 2 3 4 5

Instructions for C-2000 Controller
peration Instructions for C-2000B Controller
ANSWER A CALL FR M D RB X
When the phones ring, pick up a phone to be connected to the visitor.
PLACING C LINE CALLS N H LD (CALL WAITING)
f a phone call is in progress, and a doorbox is activated, one to four beeps will be heard (indicating which doorphone is calling).To place the call in progress on hold and
speak to the visitor, push #. When you want to return to the original phone call, push #.
ACTIVATING A D RSTRIKE R PENING A GATE
When a call is in progress, press to open the gate and return to the original call. f you do not want to open the gate, press # to return to the original call.
Strike can be activated with out the need of a “call-first” to the entry phone. Refer to the list below for codes for specific entry relays.
**
1 Move D P switch 2 from OFF to ON position.
2 Come off-hook with any house phone connected to terminals 4 & 5 LINE UT T PH NES.
3 Double beep indicates accessing the programming mode.
4 You can now program the C-2000A. The features covered in this manual are Maximum Doorphone Ring Count
and Door Strike Activation Time. For information on programming other features see the Viking C-2000 manual.
5Move D P switch 2 back to the FF position.
STEP ACTION
Access Programming Mode (Local Access)
1Follow steps 1-3 from “Access Programming Mode” (above).
2 At “double beep” enter desired number of rings, followed by #61. Example: For 7 rings, enter “07#61”.
3 Hang up the phone.
STEP ACTION
Maximum Doorphone Ring Count - Factory Default is 5 Rings
1 Follow steps 1-3 from “Access Programming Mode” (above).
2 At “double beep” enter desired number of seconds of strike activation, followed by:
#19 for Gate 1, #29 for Gate 2, #39 for Gate 3, #49 for Gate 4
Examples:
Set Gate 1 for 8 seconds (08#19); Set Gate 3 for 15 seconds (15#39)
3 Hang up the phone.
STEP ACTION
Program Gate Strike Relays - Factory Default is 0.5 Seconds
Entry Relay Strike Code
1 #1**
2 #2**
3 #3**
4 #4**
The C-2000 controller is factory set to work right out of the box. f customization of
the default settings is required, see the steps listed below. Refer to the C-2000
manual for additional options
Page 5 TYPE 6.5.0.3-RF

501 E. Goetz Ave.
Santa Ana, Ca 92707
Ph. 714-434-6904
Fax [phone]
www.eholovision.com