HOLOVISION 400-A-VIK User manual

Manual Type 6.5.0.4-RF
Viking E-10 with PAN-1
with Essex “A CII” Keypad
For Models
400-A-VIK(PAN1) 401-A-VIK(PAN1)
403-A-VIK(PAN1) 404-A-VIK(PAN1)
410-A-VIK(PAN1) 411-A-VIK(PAN1)
pecifications
IN TALLATION
IN TRUCTION
501 E. Goetz Ave.
anta Ana, Ca 92707
www.eholovision.com
Ph. 714-434-6904
Fax [phone]
HOLOVI ION
Access Control
Essex K1-26I Keypad field configurable to ASCII,
Wiegand and others.
400 Series ‘’A’’ Junction Board
Not Used
12 VDC input (for camera and keypad)
Connect tamper switch to alarm (optional)
Intercom to PAN-1 (Not polarity senitive)
Bit Parity Mode
Inverted Serial
Ground
Normal Serial
Communication
Viking E-10 Doorbox uses “half-duplex”
communication, allowing for high speaker and
microphone volume, without the possibility of
feedback. Using Viking “PAN-1” adapter, E-10
plugs directly into doorphone card of Panasonic
KSU.

Page 2 Type 6.5.0.4-RF
A CII Connection to Crestron or HAI 400
N C M NC N C M NC
Red Green LED control Gate Control
Automation System Relays
(Typical of Crestron or HAI)
To gatecontrol
HAI
To Automation System
(see details below)
Crestron
Black to pin 5
White to pin 2
Crestron Serial Port
Z1
----
Z2 Z3 Z4 Z5
GRD 12V Switched
12V AUX
24VAC
- - -
To HAI serial port:
RJ-11 Black = pin 1 White = pin 4 (RJ-11 is 4 pin)
RJ-25 Black = pin 2 White = pin 5 (RJ-25 is 6 pin)
Black
Black to “Grnd”
White
Viewed with ‘’tit’’ up
Black
Green
The red LED is normally on all of the
time. When a valid code is entered, the
relay controlling the LEDs would close,
and the green light would go on
(momentarily). Note, this relay must be
programmed in Crestron or HAI in order
for this to take place.
K1-26I
ASCII Keypad
12vDC
1.5A

For Camera
Page 3 TYPE 6.5.0.4-RF
CLINEIN
KSU
To Phones
Strike 1
Door 1
13.8
VAC
VIKING
PAN 1
Viking E-10/PAN-1 Wiring Diagram
To Automation System
To Automation System Relay N & C M
12vDC
1.5A
T GATE
C NTR LLER R
“REM TE
TERMINALS” N
ASCII
C NTR LLER

Page 4 TYPE 6.5.0.4-RF
Instructions for E-10 Doorphones
In certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom of this is one-way talk path, in which the distant party
cannot be heard over the speaker. A “MIC VOL” adjustment is provided on the doorphone for increasing or decreasing the microphone volume.
Microphone Volume
DIP Position Description
Switch
1 N Auto Answer - Doorphone answers when incoming call is detected.
2 N Call Timer - See E-10 manual for a description of this feature. Recommended setting is “ N”. This is the factory default.
3 FF Programming Mode - E-10 is factory pre-set, and normally does not need re-programming. Refer to E-10 manual
(Viking document which is included) for details
N N N
1 2 3
N N N
1 2 3
+
+
Spkr Vol
Mic Vol
Holovision recommends the default settings on the dip switches. See the E-10 manual for more information.
(E-10)
The “ PKR VOL” pot can be adjusted to increase or decrease the speaker volume to the desired level.
Speaker Volume
Dip witch ettings
Doorphone Programming