Home Accents Holiday 1004339551 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.1 A 120 V
60 Hz.
c) Do not use this product outdoors.
d) This seasonal use product is not intended for permanent installation
or use.
e)Donotmountorplaceneargasorelectricheaters,fireplace,candles
or other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personalinjury and electric shock itshouldnot be playedwithor placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light
string.
l) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
m)Donot cover theproductwith cloth,paper or anymaterialnotpartof
the product when in use.
n)Thisproductisequippedwithpush-intypelamps.Donottwistlamps.
o) This product employs overload protection (fuse). A blown fuse
indicatesan overload or short-circuit situation.If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
p) Read and follow all instructions that are on the product or provided
with the product.
q) SAVE THESE INSTRUCTIONS.
CAUTION!– ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
CAUTION
a) To reduce the risk of electric shock, use only with the
power-supply cord provided or with a cord set intended for indoor
use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Do not abuse cord – Do not carry product by the cord or yank or
pull it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
6.5FT FESTIVE PINE WITH 250L MULTI-COLORED
LED
SKU# 1004339551
Package Contents
A. Tree top
Qty: 1
B. Tree center
Qty:1
C. Tree bottom
with base
Qty:1
D. Legs of Tree base
Qty: 4
E. Fuse
Qty:2
F. Replacement
bulb
Qty:6

Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2.Insertandslidethelegsupward intotheslotsofthebaseuntilfirmly
secured.(Note: The base is already on the tree section (C).
Assembling the tree
Pleaseremoveprotectivecoversfromthe baseofthepoleforeachtree
section before assembling.
Step1. Carefully insertthe middle section (B) of the tree into the
bottom section (C). (See Fig. 1)
Step2.Insertthetop section(A)intothemiddlesection(B). (SeeFig.
2)
Step3. Insert the maleconnector of the middle section (B) intothe
femaleconnector of the top section(A),the male connectorof
thebottomsection (C) into the femaleconnectorof the middle
section (B) in right direction properly and tightly according to
the magnified drawing on Fig. 5) . (See Fig.3,4,5)
Pre-Assembly
Assembly

Step 4. Allow branches to fall into place orgently pull branches up and
out. Whenadjustingbranches be surethatallwiresare free of
branch hinges. (See Fig. 6)
Step 5. Shape the branches. Starting with tips closest to the pole,
shape one tip to the right, one to the left and one at the center
ofthemainstem. Repeatpatternforeachbranch. (SeeFig.7)
Step 6. Plug the power cord from the tree section (C) into a proper
outlet.
Turning on the tree
Step 1. Plug the power cord from the tree section (C) into a proper
outlet.
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on top of
attachment plug towards blades.
c) Remove fuse carefully.
d) Riskoffire.Replacefuse onlywith3Amp,
125 Volt fuse (provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Graspplugandremovefromthereceptacleorotheroutletdevice.Do
not unplug by pulling on cord.
b) Unlock the burned out LED bulb by lifting the hook and pulling both
the bulb and plastic base straight out of the bulb holder. Do not twist
bulbs.
c) Replace burned out bulb with 3.0/2.0 volt, 20 mA LED type bulb
ONLY. (Replacement bulbs included)
d) Lock the LED bulb.
CAUTION
1. To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0/2.0 Volt, 20 mA LED lampsonly.
2. Riskoffire.Thisproductdoesnotcontainlampshunts,whichallowthe
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1. Pull the reflector out.
2. Remove the base of burned out lamp by straightening lamp leads
and gently pulling lamp out.
3. Thread leads of new lamp through
hole in old base with one lead in each
hole (always match the long lead of
new lamp to the hook of lamp base.)
4. After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5. Insert the reflector into the base.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove the power cords from the tree
bottom (C).
Step 3. Gently lift the tree top straight up to remove from the center
section and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it
shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that connectors of all tree sections are
connected into each other well. Make sure power
cord plug is securely inserted into a working
electrical outlet.
Checkfor blown fuses atthe power cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Model No. TMP6.5-6(0.1)
Operation
Maintenance