Home Accents Holiday TG90P3742S00 User manual

Assembling the tree stand
Assembly
Step 1. Choose a location near a wall outlet.
Step 2. Unfold the legs of the tree stand (D) and lay the stand
on the floor.
Step 3. Slide the locking disk of the tree stand (D) down until
it snaps into place.
This tree assmebles with Quick Set® technology ---Set
up and light up your tree in less than 10 minutes!
Assembling the tree
Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
a. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b. Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use.When products are
used in outdoor applications,connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet.If one is not
provided,contact a qualified electrician for proper
installation.
c. This seasonal product is not intended for permanent
installation or use.
d. Do not mount or place the product near gas or electric
heaters, fireplaces,candles, or other similar sources of heat.
e. Do not secure the wiring of the product with staples or
nails, or place on sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g. Unplug the product when leaving the house, when retiring
for the night, or if left unattended.
h. This is an electric product and not a toy!To avoid riskof fire,
burns,personal injury and electric shock it should not be
played with or placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire, or
light string.
k. Do not close doors or windows on the product or
extensions cords as this may damage the wire insulation.
l. Do not cover the product with cloth, paper, or any material
that is not a part of the product when in use.
m. This product has a polarized plug (one blade is wider than
the other) as a feature to reduce the risk of electric shock.
This plug will fit in a polarized outlet only one way.If the
plug does not fit fully in the outlet, reverse the plug.
If it still does not fit,contact a qualified electrician.Do not
use with an extension cord unless plug can be fully inserted.
Do not alter or replace the plug.
n. This product is equipped with push-in type lamps.Do not
twist lamps.
o. This product employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation.If the
fuse blows, unplug the product from the outlet.Also
unplug any additional strings or products that may be
attached to the product.Replace the fuse as per the user
servicing instructions (follow product marking for proper
fuse rating) and check the product.
p . Read and follow all instructions that are on the product or
provide with the product.
q. SAVETHESE INSTRUCTIONS
When using electrical products, basic precautions should
always be followed, including the following:
Tree top
Section 2
Section 1
Insert
Green Label
Plug Into Wall
Outlet
S100
S100
S100
S100
S100
S50
Foot Pedal
on/off Switch
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
S50
S100
S100
S100
Christmas Tree
Model: TG90P3742S00
Sku #1003 173 212
Top view Side view
TM
Step 1. Remove the protective caps from the tree bottom (C)
and zinsert the pole into the tree stand (D).
Step 2. Remove the protective caps from the tree center (B)
and insert the pole into the tree bottom (C) .
Step 3. Insert the tree top (A) into the tree center (B).
Step 4. Shape the branches to your preference by working
from the bottom to the top. When adjusting branches,
ensure that all wires are free of branch hinges.
Step 5. Insert the green label extension cord plug into the
wall outlet. All your lights should now be lit.
Step 6. Shape the tree from the bottom to the top. Start with
the branches farthest from the pole – fan out in a star
shape, and continue until the entire tree is shaped.
Step 7.
When finished shaping the branches, slightly upsweep
all branch tips for a uniform look.

Package Contents
Pre-Assembly
Part
D
A
Description
Tree stand
Tree top
Tree center, Sticker 2
Tree center, Sticker 1
B
C
1
1
1
1
Quantity
Christmas Tree
Model: TG90P3742S00
Sku # 1003 173 212
Operation
Turning on the tree
Maintenance
Spare parts
Repairing Loose Hinges
Use and Care Instructions
WWARNING - Risk of fire: This product employs overload
protection (fuse lamp) in each series light circuit to provide
overload protection in addition to the fuse(s) located in the
plug. Do not replace the fuse lamp contained in this set with
any other type of lamp, use only spare fuse lamps provided
with this product. In case of a burnt out FUSED lamp, the entire
series of 50 lamps will be out. To replace the fused lamp:
User servicing instructions
Fused Lamp Replacement
The tree
does not
light
Troubleshooting
Problem Solution
Ensure that all tree sections are plugged into
each other and that the tree is plugged into the
wall. If your tree came with a foot pedal, step on
the On/Off button.
Check for loose, broken, or missing bulbs and
replace as needed with the replacement bulbs
provided.
Check for blown fuses at the light string and
power cord plugs. Replace as needed with the
replacement fuses provided.
For blown fuses (if applicable), please refer to
User Servicing Instructions – Fuse Replacement
and replace as instructed.
TM
NOTE: If some bulbs do not light or flicker, search for any
loose plugs and/or broken, loose, or missing bulbs. Replace
bulbs promptly with the replacement bulbs provided in
order to maintain the performance and life expectancy of
your tree.
Step 1. Connect the light strings of the tree together and
plug the power cord into a wall outlet.
Step 2. If the tree comes with a foot pedal, step on the
On/Off button.
This tree package includes hinge pins,washers, bulbs, and
fuses for any replacement or repair that you need to perform
on your tree. If extra parts are needed, contact the Customer
Service Team at 1-877-527-0313 between the hours of 8 am
and 5 pm EST,Monday through Friday.
Step 1. Place the branch into the slot of the bracket
Step 2. Insert a new hinge pin through the holes of the
bracket and secure with a washer.
1. Before using or reusing, inspect product carefully. Discard
any products that have cut, damaged or frayed wire
insulation or cords, cracks in the lampholders or
enclosures, loose connections, or exposed copper wire.
2. Before disassembling the tree, unplug the tree and remove
all ornaments and decorations.
3. Gently lift the tree top straight up to remove from the
center section and fold all branches towards the pole.
4. Repeat this step for the center and bottom tree sections.
5. When storing the product, carefully
remove the product rom wherever it
is placed, including tree, branches,
or bushes, to avoid any undue strain
or stress on the product conductors,
connections, and wires. Cover the
protective cap on the poles to avoid damaging the internal
parts.
6. When not in use, store neatly in a cool, dry location
protected from sunlight.
1. Grasp the plug and remove from
the receptacle or other outlet
device. Do not unplug by pulling
the cord.
2. Locate the fused lamp with gray
color lamp holder. Pull the burnt
fused lamp and plastic lamp base
straight out of the lamp holder.
3. Replace with a spare fused lamp.The fused lamp can be
distinguished by a gray lamp base and an additional clear
plastic cover.
4. Plug in the lights again.
SPARE FUSE
Fuse replacement
1. Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by
pulling on cord.
2. Open fuse cover.Slide open
fuse access cover on top of
attachment plug towards
blades.
3.Remove fuse carefully.
4.Risk of fire.Replace fuse only
with 5, 7 or 10 Amp, 125Volt fuse for the power cord set.
5. Close fuse cover. Slide closed the fuse access cover on top
of attachment plug.
6. Risk of fire.Do not replace attachment plug.Contains a
safety device (fuse) that should not be removed. Discard
product if the attachment plug is damaged.