Home Accents Holiday 1003144370 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.6 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i) This is an electric product –not a toy! To avoid risk of fire, burns personal
injury and electric shock it should not be played with or placed where small
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of the
product when in use.
n) This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or products
that may be attached to the product. Replace the fuse as per the User
Serving instructions (follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
Pre-Assembly
Package Contents
Part
Description
Quantity
A
Tree top
1
B
Upper middle section
1
C
Lower middle section
1
D
Tree bottom
1
E
Tree stand
1
F
Power cord
1
G
Remote control
1
7.5’Elegant Natural Fir LED Pre-Lit Tree with Timer
SKU# 1003144370
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! –ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (D) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insert lower middle section (C) into the tree bottom (D). (See Fig. 2)
Step 3 Insert upper middle section (B) into the lower middle section (C).
(See Fig. 3)
Step 4. Insert tree top (A) into the upper middle section (B). (See Fig. 4)
Warning: There is a tree top connector on the tree top (A). Do
not overload. Connect other lighting strings or tree toppers
end-to-end up to a maximum of 216 Watts (1.8 Amps). Do not
interconnect low-voltage products.
Step 5. Insert the provided power cord into the connector on the tree
bottom (D) in right direction porperly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (D) according to the
magnified drawing on fig. 5.).
Step 6. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 6)
Step 7. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of the main
stem. Repeat pattern for each branch. (See Fig. 7)
Step 8. Plug the power cord into a proper outlet. This tree comes with a
control box and a remote control. You can change the lighting
patterns of the tree by using control box or remote control.

Please see Instructions of control box and remote control
as below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the power cord into a wall
outlet.
Instruction of control box and remote
control
Instruction of control box
1. Press the ON/OFF Timer button on control box more than 1 second
to turn on and off timer function.
2. Press the ON/OFF Timer button on control box for more than 2
seconds to select below timer hours:
i. Indicator lights of timer on control box turn on red:
The tree lights will automatically run through a 2-hours
ON, 22-hours OFF cycle.
ii. Indicator lights of timer on control box turn on green:
The tree lights will automatically run through a 4-hours
ON, 20-hours OFF cycle.
iii. Indicator lights of timer on control box turn on blue:
The tree lights will automatically run through a 6-hours
ON, 18-hours OFF cycle.
iv. Indicator lights of timer on control box turn on yellow:
The tree lights will automatically run through an 8-hours
ON, 16-hours OFF cycle.
No memory mode on timer whether the tree or the timer is
re-started.
3. Press the Brightness Adjustment button more than 1 second to
select the brightness of tree lights as indicator lights of brightness
indicate.
There is memory mode on brightness adjustment.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. The first button is for the on/off power switch for the lights.
2. Press the second button to select the brightness of tree lights as
indicator lights of brightness indicate on the control box.
There is memory mode on brightness adjustment.
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Use cross screwdriver to open the back cover
of the remote control.
2. Replace with a new alkaline “A23G” (12 volt)
battery into the compartment.
WARNING:This is not a toy and is not intended for use by children.
(A) Do not dispose of the battery in fire as the battery may leak and
explode.
(B) Do not mix old and new batteries and do not mix alkaline, standard
(carbon-zinc), or rechargeable (nickel-cadmium) batteries.
(C) Always purchase the correct size and grade of battery most suitable
for the intended use.
(D) Replace all batteries of a set at the same time.
(E) Clean the battery contacts and also those of the device prior to
battery installation.
(F) Ensure the batteries are installed correctly with regard to polarity (+
and -).
(G) Remove batteries from equipment which is not to be used for an
extended period of time.
(H) Remove used batteries promptly.
(I) Exhausted batteries are to be removed from the product.
(J) Use type “A23G” (12 volt) batteries.

Maintenance
Replace the fuse.
1. Power cord fuse replacement (replaceable 3 amp, 125 volt fuse is
located in spare parts bag):
2. Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
3. Open fuse cover. Slide open the fuse access cover on back of control
box.
4. Remove fuse carefully.
5. Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with
product).
6. Close fuse cover. Slide closed the fuse access cover.
7. Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment plug
is damaged.
CAUTION! –ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE REPLACEMENT.
CAUTION: To reduce the risk of fire or electric shock, do not
attempt to replace lamps or modify string.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (D) and save them.
Step 3. Gently lift the tree top straight up to remove from the center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step 5. Carefully place all tree sections into a shipping box and tape it shut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected well and that
the tree is plugged into the wall outlet. Make sure the
power cord is well connected to the tree bottom (D).
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and
receiver.
●Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician
for help.
UL Model No. LTW36C-12V1C