Home Decorators Collection OSSA CF2001-N User manual

USE AND CARE GUIDE
OSSA 52-INCH SMART CEILING FAN
Questions, problems, missing parts? Before returning to the store,
call Home Decorators Collection Customer Service
8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday.
1-800-986-3460
HOMEDEPOT.COM/Hubspace
THANK YOU
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Home Decorators Collection!
Item# 1008926194,1008872986
Model# CF2001-N, CF2001-B

2
Table of Contents ................................................................ 2
Safety Information............................................................... 2
Warranty ............................................................................... 3
Pre-Installation .................................................................... 4
Installation............................................................................ 6
Assembly.............................................................................. 7
Operation ........................................................................... 12
Care and Cleaning............................................................. 15
Troubleshooting................................................................. 16
WARNING: To reduce the risk ofpersonal injury,
do not bend the blade brackets (also referred toas
anges) during assembly or after installation. Do not
insert objects in the path of the blades.
WARNING: To avoid possible electrical shock,
turn the electricity off at the main fusebox before
wiring. Ifyou feel you donot have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: To reduce the risk of re or electric shock,
do not use this fan with any solid state speed control
device.
Safety Information
Table of Contents
CAUTION: To reduce the risk of personal injury,
use only the screws provided with the outlet box.
WARNING:
shock, this fan should only be used with fan speed
control part no. D-SLF-A17-01-A, manufactured by
LEEDARSON LIGHTING CO., LTD.
READ AND SAVE THESE INSTRUCTIONS.
1. To reduce the risk of electric shock, ensure the electricity has been
turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordance with the National Electrical Code
ANSI/NFPA 70-1999 and local electrical codes. Electrical installation
should be performed by a qualied licensed electrician.
3. To reduce the risk of re, electric shock, or personal injury, mount to
outlet box marked acceptable for fan support of 35 lbs (15,87 kg ) on
less and use mounting screws provided with the outlet box. Most
outlet boxes commonly used for the support of lighting xtures are
not acceptable for fan support and may need to be replaced. Consult
a qualied electrician if in doubt. The xing means for attachment to
the ceiling such as hooks or other devices shall be xed with a
sufcient strength to withstand 4 times the weight of the ceiling fan.
4. To reduce the risk of injury to persons,install fan so that the blade is
at least 7 ft (2.1m) above the oor.
5. Do not operate the reversing switch while the fan blades are in
motion. You must turn the fan off and stop the blades before you
reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, use
caution when working around or cleaning the fan.
8. After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into the outlet box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box.
The ungrounded conductor on the other side of the outlet box.
9. All setscrews must be checked and retightened where necessary
before installation.
WARNING: To reduce the risk of re or electric shock,
this fan must be installed with an isolating wall switch.
WARNING: All replacement of parts and the mounting
of the safety suspension system device shall be
performed by qualied licensed electricians.
WARNING: To reduce the risk of personal injury, if
unusual oscillating movement is observed, immediately
stop using the ceiling fan and contact with a qualied
licensed electrician.
To reduce the risk of injury to persons, not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the fan by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the fan.

3HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.
Warranty
Contact the Customer Service Team at 1-800-986-3460 or visit HOMEDEPOT.COM/Hubspace.
The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime
after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any glass or acrylic blades, to be
free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the date of purchase by the
original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is
returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product
are your responsibility. Damage to any part, such as by accident, misuse, improper installation, or by afxing any accessories, is not covered by
this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass nish, including rusting, pitting, corroding,
tarnishing, or peeling. Brass nishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of
"wobble" is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is
no other express warranty. Home Decorators Collection hereby disclaims any and all warranties, including but not limited to those of merchantability
and tness for a particular purpose to the extent permitted by law. The duration of any implied warranty, which cannot be disclaimed, is limited
to the time period as specied in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above
limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with
product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential
damages, so the above exclusion or limitation may not apply to you. This warranty gives specic legal rights, and you may also have other rights that
vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty
must be paid by the customer.
Wireless Protocol
Apple and the Apple logos are trademarks of Apple, Inc., registered in
the U.S., and other countries. App Store is a service mark of Apple Inc. Google and Google Play are trademarks of Google LLC.
Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
FCC compliance information is listed as below:
Responsible party: Leedarson America, Inc.
Responsible party address: 300 Technology Court SE Suite 100, Smyrna, GA 30082
Telephone number: [phone]
FCC Warning
Safety Information

4
AA HH I I
JJ
KK LL MM
Pre-Installation
SPECIFICATIONS
TOOLS REQUIRED
Phillips
screwdriver
Flat blade
screwdriver
Adjustable
wrench
Electrical
tape
Wire cutter Step ladder
5003280
Size Speed Volts Amps Watts RPM CFM Net
Weight
Gross
Weight Cu. Ft.
52 in. 120
0.06
0.09
0.14
0.23
0.33
0.53
1
2
3
4
5
6
3
5
9
15
23
39
70
94
124
154
179
206
1800
2300
3100
3900
4600
5500
16.09lbs
(7.3 kg)
21.83lbs
(9.9 kg)
2.237
NOTE: These are approximate measures. They do not
include the amps and wattage used by the light kit.
HARDWARE INCLUDED NOTE: Hardware not shown to actual size.
Pre-Installation (continued)
Part Description Quantity
AA Wire nut (P4) 3
HH Extra blades attachment screws (3/16-24*12mm)
Extra blades attachment washer 1
JJ Remote control
Anchor
Screw-4 (ST3*20)
1
I I Balancing 1
KK 2
LL 2
MM Remote Bracket 1
NN AAA battery 2
NN

5
PACKAGE CONTENTS
Pre-Installation (continued)
AHook
Remote
antenna
(Yellow)
C K
D
E
L
F
G
I
J
B
Part Description Quantity
A Mounting plate 1
B Fan-motor assembly 1
C Ceiling housing 1
D Trim ring 1
E 1
F LED module
Light housing
1
Part Description Quantity
G Glass shade 1
I Rotary plate 1
J Connect plate 1
K Blade 3
L Wi antenna 1
HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.

6
Installation
MOUNTING OPTIONS
WARNING:
personal injury, mountto outlet boxmarked “Acceptable
for fan supportof 35 lbs. (15.9 kg) or less”, and use
screws provided with theoutletbox. An outlet box
not be acceptable for fan support and may need to be
If your ceiling fan does not have an existing UL-listed mounting
box, then install one using the following instructions:
□Disconnect the power by removing the fuses or turning off
the circuit breakers.
□Secure the outlet box directly to the building structure. Use
the appropriate fasteners and materials. The outlet box and
support structure must be securely mounted and capableof
reliably supporting 35 lbs. (15.9 kg). Use onlyUL Listed outlet
boxes marked “Acceptable forFan Support of 35 lbs. (15.9 kg)
or less.” Do not use a plastic outlet box.
The illustrations below show two different ways to mount the
outlet box.
you may need an installation hanger bar as shown above
(available at any Home Depot store).
Outlet Box
Outlet Box
Outlet Box
Hanger Bar

7
Assembly - Hanging the Fan
Hang the fan-motor AssemblyInstall the mounting plate to ceiling 21
HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.
□
□
□
There are 8 pre-installed screws (4 side-N; 4 bottom - M) on the
mounting plate (A).
Remove 2pcs opposite screws from the side and bottom of
mounting plate(A). Figure 1.
Attach the mounting plate (A) to the outlet box (not included)
with two screws(EE, not included) and washers(DD, not
included) supplied with the outlet box. Ensure the mounting
plate (A) is tight, level and secured. Figure 2.
NOTE: Save all screws removed to be added back in a later
step.
M
M
M
M
N
N
N
A
N
Elongated
shaped hole
Side screw (N)
Bottom screw(M)
Figure 1
Figure 2
B
□Carefully lift the fan-motor assembly (B) and hang the
fan-motor assembly (B) on the hook of the mounting plate
(A) by utilizing the hole edge trim of the fan-motor assembly
plate (B) and make sure it is securely suspended. Figure 3.
Figure 3
EE
A
DD
outlet box

8
Assembly - Hanging the Fan (continued)
□Identify the wiring located inside of fan-motor assembly (B):
black – line voltage, white – neutral, green – ground .
Connect the Black (L), White (N) and Green (G) wires from the
fan-motor assembly (B) to their corresponding wires from the
outlet box using Wire Nuts (AA).
□
□
□
□
□
□
Carefully lift the wi antenna(L) through the gap of mounting
plate (A) away from fan-motor assembly(B).
Locate the two key holes on the edge trim of fan-motor
assembly (B).
Place two key holes on the mounting bottom screws(M)
pre-installed on the bottom of mounting plate (A) . Figure 5.
Rotate the fan-motor assembly(B) clockwise until it is secure.
Reattach 2pcs of the bottom screws (M) which removed in
Step 1 in place.
Tighten 4pcs bottom screws (M) of mounting plate (A).
Install the fan-motor assembly
A
B
M
M
M
M
L
N
N
L Wifi Antenna
Screw hole
Key hole
C
4
Connect the wires
3
□
□
□
□
□
Locate the two key holes on the top of ceiling housing (C).
Place two key holes on the mounting side screws (N) pre-installed
on the side of mounting plate (A) .
Rotate the ceiling housing (C) clockwise until the screw holes in
place between ceiling housing (C) and mounting plate (A).
Reattach 2pcs of the side screws (N) which removed in Step 1 in
place.
Tighten 4pcs side screws (N) of mounting plate (A).
Install the ceiling housing
5
CAUTION: Please take care of Wi antenna in this step.
Figure 5
B
L
Mounting Plate
Group - Green
Receiver
Group - Green
Remote antenna
(Yellow)
120V Neutral-White
120V Line
voltage-Black
120V Group-Green
Fan Neutral - White
Fan Line voltage - Black
Fan Group- Green

9
Assembly - Hanging the Fan (continued)
□
□
□
□
□
Locate the slotting inside of trim ring (D).
Carefully lift the trim ring (D) until the slotting in place through
the 4pcs side screws (N) which tightened in Step 5.
Carefully rotate trim ring (D) clockwise until it is secure.
Make sure that the wi anteena (L) is close to to the ceiling.
Remove the sticker from the antenna and stick the antenna to
the ceiling outside the ceiling fan.
□
□
□
Remove all blade screws from the rotary plate (I) of fan-motor
assembly (B).
Insert the blades (K) into holes of the rotary plate (I) in place.
Reattach all blade screws through the blade washers and
tighten all screws to make sure the blades (K) is secure.
Install the blades
7
Install the trim ring
6
HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.
D
L
Slotting
Blade washer
Blade screw
Blade screw
Blade washer
K
I

10
Assembly - Hanging the Fan (continued)
□
□
□
□
□
Remove one screw from the connect plate (J) of fan-motor
assembly (B). And loosen other 2pcs screws away from 3/4 length.
Locate the key hole of light housing (E).
Place two key holes on the mounting screw loosened on the
connect plate (J).
Reattach 1pc screw through light housing (E) in place to the
connect plate (J).
Tighten 3pcs screws until light housing (E) is secure.
□
□
□
□
□
□
Remove 3pcs pre-installed screws from inside of the light
housing (E).
Connect the terminal from LED module (F)and fan-motor assembly (B).
Locate 3pcs screw holes of LED module (F).
Place three screws holes between LED module (F) and light housing (E).
Reattach 3pcs screws through the screw holes of LED module (F).
Tighten the screws until LED module (F) is secure.
Install the LED module
9
Install the light housing
8
E
J
Key hole
F
screws
E
CAUTION: To reduce the risk of electric shock, disconnect the
electrical circuit to the fan before installing light kit.

11
Assembly - Hanging the Fan (continued)
□Rotate the glass shade (G) clockwise until it is secure. □
□
□
Using the remote bracket (MM)as a guide, mark the two holes
locations.
Drill the two holes at the marked locations and install two
anchors (KK) in each of the marked locations.
Insert screw (LL) into anchor and tighten each screw.
Install the remote bracket
11
Install the glass shade
10
HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.
GWall
KK
LL
MM

12
Remote Operation
433 Remote control
Your fan isequipped with a remote control to operate the speed and
lightsfor your new ceiling fan.
effect. This allows you to set your air conditioner on a warmer setting
without affecting your comfort.
the
ceiling. This allows you to set your heating unit on a cooler setting
without affecting your comfort.
NOTE: Wait for the fan to stop before reversing the direction of the
blade rotation. Warm weather
Cool weather
NOTE:
This is NORMAL OPERATION for DC ceiling fan as it goes through its
calibration cycle. This fan is NOT DEFECTIVE.
On start up your ceiling fan will oscillate back and forth.

13
Remote Operation
HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.
NOTE: Ceiling fan power on within 30seconds, press and hold the light power button above 5seconds to pair between remote
and ceiling fan or cancel the pairing.
NOTE: Press and hold the fan power button above 5second to reset factory default setting, reset status will be closed after
2seconds. Factory default setting: 3000K, 100% brightness, fan foreward ,fan speed is level 6.
NOTE: Disconnect the power supply or wall control switch as a way to override intelligent or remote control.
Icon Button Name Action Notes
Light ON/OFF Press once to turn the light on
Press again to turn the light off
The brightness and CCT will be the
same as your last setting when
turned on.
Fan ON/OFF
Press and release the button while the
light is on to change the brightness by
10% - 50% - 100%, then dim 50% -
10%
If pressed while the light is off; the
light will turn on the last setting of
brightness and CCT.
The factory default is 100%.
Press and release while the light is on
to change the CCT by 2700K – 3000K –
3500K – 4000K – 5000K – 6500K
The default CCT is 3000K.
If pressed while the light is off; the
light will turn on the last setting of
brightness and CCT.
Press once to turn the fan on
Press again to turn the fan off
Brightness Change
Correlated Color
Temperature (CCT)
Change
Fan Direction Press and release the button while the
fan is on to reverse the direction.
Natural Wind Press and release the button to enter
natural wind mode.
Press and release the button to exit
natural wind mode.
In natural wind mode, the fan speed
will vary (increase or decrease)
automatically. The fan will not be set
on a xed speed in this mode
The fan has 6 speeds: Press and release
the button to change the fan speed.
Select the desired timer button on the
remote. The fan will remain on for this
duration.
The timer is set for the fan.
The default fan speed is level 6.
Fan Speed
Timer Buttons
2H
4H
8H

xxxx - xxxx
xxxx - xxxx
xxxx - xxxx
1Download the Hubspace™ app from
the App Store or the Google Play
Store. 2Create an account to sign in or log in
if you already have an account.
For more information on the Hubspace app,
visit hubspace.com/Hubspace.
3Connect your ceiling fan to power
and follow the instructions on the
app screen.
4Tap the ‘+’ button in the upper right
corner to add your ceiling fan.
5Scan the QR Code 6Using Your Smart Ceiling Fan
□Scan the QR code in the quick start guide or on
the ceiling fan. To scan the QR code on the
ceiling fan, diffuser needs to be removed.
Please follow step 1 in the Installations.
□
□
Turn your smart ceiling fan on or off from the Home
page on the Hubspace app.
To set a schedule or timer, tap the name of the
smart ceiling fan on the Home page. You will see
options for setting Schedules and Auto-Off Timers.
7Set up your Voice Assistant
□You can connect your smart ceiling fan to Google
Home and Alexa from the Hubspace app.
Or, you can sign in to Alexa app or Google Home
and connect to your Hubspace devices from there.
NOTE:
If the QR code cannot be scanned, you can enter the
HUBSPACE APP QUICK START GUIDE
code manually. Tap Enter Code and follow the instructions.
NOTE:
□This Hubspace device requires a 2.4GHz Wi-Fi channel.
Hubspace only shows Wi-Fi networks that your device can use.
□If you do not see your Wi-Fi network name when you attempt to
connect your devices, please check your router settings or move
your product closer to your Wi-Fi router.
My Home
NOTE: Bluetooth access is required for device setup.
Smart Setup Operation
xxxx - xxxx
xxxx - xxxx
xxxx - xxxx
14

Voice Commands
Alexa
When you want to... Ask Alexa to...
Turn on the fan only. … turn on <devicename> fan power.
Turn off the fan only. … turn off <devicename> fan power.
Turn on the light only. … turn on <devicename> lightpower.
Turn off the light only. … turn off <devicename> lightpower.
Change the brightness. ... Set <devicename> brightness to 100%.
… Set <device name> light to 10%.
…Make <devicename> dimmer.
…Make <devicename> brighter.
… Dim <device name>.
…Brighten <devicename>.
… Dim <group name>.
…Brighten <group name>.
Change the White Temperature. … Change<devicename> to Cool White.
… Change<devicename> to Warm White.
… Change<devicename> to Daylight White.
… Change<devicename> to White.
Change the fan speed. … Set <device name> speed to fastest.
… Set <device name> speed to fast.
… Set <device name> speed to medium.
… Set <device name> speed to slow.
…Increase <devicename> speed.
… Decrease<devicename> speed.
Turn on Comfort Breeze. … Turn on Comfort Breeze on <device name>
When you want to... Ask Google to...
Turn on the fan only. … turn on <devicename> fan power.
Turn off the fan only. … turn off <devicename> fan power.
Turn on the light only. … turn on <devicename> light power.
Turn off the light only. … turn off <devicename> lightpower.
Change the brightness. ... Set <devicename> brightness to 75%.
…Set <device name> lightto25%.
…Brighten <devicename>.
…Dim <device name>.
…Brighten <room name>.
…Dim <room name>.
Change the White Temperature. … Change <device name> toIvory.
…Change <device name> toDaylight.
…Change <device name> toCool White.
…Change <device name> to Warm White.
... Change<devicename> to Incandescent.
Change the fan speed. … Set <device name> speed tofastest.
…Set <device name> speed tofast.
…Set <device name> speed tomedium.
…Set <device name> speed toslow.
…Increase <devicename> speed.
…Decrease <devicename> speed.
Turn on Comfort Breeze. … Turn on Comfort Breeze on <device name>
Google
The Ossa 52 in. LED Indoor SmartColor Changing Ceiling Fan works with Alexa and Google Assistant.
Thissection lists some of thevoice commands you can use. To view these and other commands, go to http://hubspaceconnect.com.
□Becauseof thefan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade
attachments twice a year. Make sure they are secure. Itisnot necessary to remove the fan from the ceiling.
□Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as thiscould damage
plating is sealed with a lacquer to minimize discoloration or tarnishing.
□You can applya light coatoffurniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a
light application ofshoepolish.
□You donotneed tooil your fan. The motor has permanently-lubricated sealed ball bearings.
WARNING: Make sure the power is off before cleaning
your fan.
Care and Cleaning
15 HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.

16
Troubleshooting
Problem Solution
The fan will not start. 1. Check to make sure the wall switch is in the on position if applicable.
2. Check the main and branch circuit fuses or breakers.
3. Make sure your device is connected to a power source.
4. Check the battery in the remote control, the transmitter and receiver are matched.
1. Make sure the fan was not damaged prior to installation.
2. Ensure the screws that attach the fan blade bracket to the motor hub are tight.
3. Ensure the hanging units are xed and tight.
4. Ensure the glass shade is secure.
5. Ensure the motor assembly does not contain any debris.
1. Due to different weight and density of blades, the blades cannot be replaced by other type or it will effect its
balance while working.
2. Ensure the screws that attach the fan blade bracket to the motor hub are tight.
3. Ensure the hanging units are xed and tight.
4. If the above are normal, you can adjust the device according to the guide of balancing kit.
The fan is noisy.
The fan wobbles
1. Check the power connection from the fan to the electrical power supply;
2. Check if the terminal from the LED module is connected properly.
3. Check if the LED Module is damaged.
Lighting source
is not working
Make sure no disturbance from same frequency controller, you may rematch the device according to guidance.
Ceiling fan is
uncontrollable by
remote device
This is normal start-up procedure for DC motor fans. The partial movement during start-up is the result of the DC
motor aligning the internal magnetic poles for proper motor operation. This design saves electricity and allows the
fan to operate much quieter than standard AC motor fans.
Fan moves backwards
and forwards when
turned on.
NOTE: Make sure the power is off before maintenance
NOTE: On start up your ceiling fan will oscillate back and forth.
The Balancing Kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owner’s Manual
under "Attaching the Fan Blades."
1.Turn the fan on and set the speed control setting to a speed at which the wobble is the greatest.
2. Turn off the fan and allow it to come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder
and the blade tip on the trailing edge of the blade.
3.Turn the fan on.Note whether the wobble has increased or decreased.Turn the fan off, move the clip to another blade, and retest.Repeat
this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement.Move the clip inward and outward on this blade and operate the fan
to nd the position where the clip gives the greatest improvement.
5.Remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.
6.If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and
additional weights.
The guide of balancing kit
This is NORMAL OPERATION for DC ceiling fan as it goes
through its calibration cycle. The fan is NOT DEFECTIVE.

Problem Solution
My Hubspace device is not
connecting to Wi-Fi.
Make sure your device is connected to a power source. Your Internet
connection or Wi-Fi network may be down.
My device cannot nd any
Wi-Fi networks.
Make sure you have a 2.4GHz capable Wi-Fi network within range of the
device you are trying to add.
Yes. Use the app on a phone with an Internet connection like LTE. The phone
must be within Bluetooth range of your Hubspace device and have Bluetooth
enabled.
It is on the ceiling fan housing. A copy of the QR code is also included in your device’s
documentation.
Under the QR code are numbers. You can enter those in manually instead of
scanning the code.
1. Make sure the device is connected to power.
2. In the Hubspace app, tap +, then Add Device.
3. On the Scan Device screen, tap the Search button in the lower right corner.
4. Follow the onscreen instructions.
Scan the QR code and it will transfer to your account.
My device is in a location that
does not have Wi-Fi. Can I still
use it with the Hubspace app?
I cannot nd the QR code.
The QR code has become damaged. How do I add the
device?
I lost my QR code. How do I add a device?
The device is on another account. How do I transfer it?
Make sure your Wi-Fi signal strength is sufcient. You may need to move
your router, use mesh Wi-Fi, or Wi-Fi extenders.
My device is ofine for long periods of time.
Turn off Bluetooth on your phone and turn it back on. Then, scan the QR
code. If the problem persists, turn your phone off and on, then try again.
The device is on and I scanned the QR code, but the
app cannot connect to it.
No. Each product has a unique QR code.Can I scan the same QR code to add multiple products?
Troubleshooting
17 HOMEDEPOT.COM/Hubspace
Please contact 1-800-986-3460 for further assistance.

Questions, problems,missing parts? Before returning to the store,
call Home Decorators Collection Customer Service
8 a.m. - 7 p.m.,EST, Monday-Friday, 9 a.m. - 6 p.m.,EST, Saturday
1-800-986-3460
HOMEDEPOT.COM/Hubspace
Retain this manual for future use.