Home Decorators Collection BRANNEN 304602332/112302/23MM30514-PO83 User manual

USE AND CARE GUIDE
BRANNEN ELECTRIC FIREPLACE MEDIA MANTEL
304602332/112302/23MM30514-PO83
304602468/112289/23MM30514-PC72
304602334/112296/23MM30514-PT01
We appreciate the trust and condence you have placed in Home Decorators through the purchase of this electric replace. We strive to
continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Home Decorators!
THANK YOU
QUESTIONS, PROBLEMS, MISSING PARTS? BEFORE RETURNING TO THE STORE,
CALL HOME DECORATORS COLLECTION CUSTOMER SERVICE
8 A.M. - 7 P.M., EST, MONDAY - FRIDAY, 9 A.M. - 6 P.M., EST, SATURDAY
1-800-986-3460
HOMEDEPOT.COM/HOMEDECORATORS

2
MAXIMUM LOAD 90 lb. (40.8 kg)
MAXIMUM LOAD 20 lb. (9.1 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
MAXIMUM LOAD 15 lb. (6.8 kg)
CAUTION: This unit is intended for use only with the products and maximum weights indicated. Use with other products or products heavier
than the maximum weights indicated may result in instability causing possible injury.
NOTE: Flat Panel TVs with base support should be placed squarely in the center of the stand with no overhang on any side.
Maximum Load Warning ...........................................2
Safety Information.....................................................3
Warranty ..................................................................... 5
Pre-Assembly............................................................. 6
Hardware Included ................................................... 6
Product Specications....................................................... 6
Tools Required ................................................................... 6
Package Contents.............................................................. 7
Assembly....................................................................8
Operation .................................................................19
FCC/IC Information......................................................... 21
Care & Cleaning.......................................................21
Troubleshooting.......................................................22
Replacement Parts.................................................. 23
Maximum Load Warning
Table of Contents

3
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Please read and understand this entire manual before
attempting
to assemble, operate or install the product. If you
have any question regarding the product, please call customer
service at 1-800-986-3460, 8 a.m.-7 p.m., EST, Monday-Friday,
9 a.m. - 6 p.m., EST, Saturday.
When using electrical appliances, basic precautions should
always be followed to reduce the risk of re, electrical shock,
and injury to persons including the following:
1. Read all instructions before using this appliance.
2. If possible, always unplug this appliance when not in use.
3. Only a qualied service person should repair this product.
4. Do not use outdoors.
5.
Do not cover the cord under the carpeting. Do not cover
with throw rugs, runners or the like. Arrange the cord away
from trafc areas and where it will not be tripped over.
6. To disconnect this appliance, turn the controls to the off
position, and then remove the plug from the outlet.
7. Connect to properly grounded outlets only.
8.
This appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the current CSA C22.1
Canadian Electrical Code. For U.S.A. installations, follow
local codes and the National Electrical Code, ANSI/NFPA
NO.70.
9. This appliance has hot and arcing or sparking parts inside.
Do not use it in areas where gasoline, paint or ammable
liquids are used or stored. This replace should not be
used as a drying rack for clothing. Do not hang Christmas
stockings or other decorations on or near this product.
10. There is a thermostat limiter inside the heater. When inner
temperature overheating or abnormal heating occurs, the
thermostat protective device will cut off the power supply
to avoid damage to the replace or risk of re.
Safety Information
DANGER:
High temperatures may be generated under
certain abnormal conditions. Do not partially or fully cover
or obstruct the front of this heater.
WARNING: If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
WARNING: Under no circumstances should this fireplace be
modified. Parts that must be removed for servicing must be re-
placed prior to operating this replace again.
WARNING: In order to avoid overheating, do not cover the
heater.
WARNING:
Use extreme caution when operating heater
near children and the disabled.
WARNING:
Do not insert or allow foreign objects to enter
any ventilation or exhaust opening as this may cause an electric
shock or re, or damage the appliance.
WARNING: To prevent a possible re, do not block air intakes
or exhaust in any manner. Do not use on soft surfaces, like a bed,
where the opening may become blocked.
WARNING:
This appliance has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint or ammable
liquids are used or stored. This replace should not be used as a
drying rack for clothing. Do not hang Christmas stockings or other
decorations on or near this product.
WARNING:
Use this appliance only as described in the manual.
Any other use not recommended by the manufacturer may cause
re, electric shock or injury to persons.
WARNING: This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never locate this
appliance where it may fall into a bathtub or other water container.
WARNING: This appliance is not a toy. Supervise children
playing near it.
WARNING:
This heater may include an visual alarm to warn
that parts of the heater are getting excessively hot. If the alarm
illuminates, immediately turn the heater off and inspect for any
objects on or adjacent to the heater that may have blocked the
airow or otherwise caused high temperatures to have occurred.
DO NOT OPERATE THE HEATER WITH THE ALARM ILLUMINATING.
CAUTION:
Never leave the heater operating unattended.
Extreme caution is necessary if unsupervised children or invalids
are nearby.
CAUTION:
Before assembly, carefully use scissors or a utility
knife to cut and unwrap all parts. Make sure you do not discard
the hardware.

4
NOTE:
To avoid injury from unexpected starting or electrical
shock, do not plug the power cord into a source of power during
unpacking and assembly. The cord must remain unplugged
whenever you are adjusting/assembling the replace.
If any part is missing or damaged, do not attempt to use or
plug in the power cord until the missing or damaged part is
correctly replaced. To avoid electric shock, use only identical
replacement parts when servicing double-insulated tools.
NOTE:
Use care in assembling your new fireplace. Take your
time and use the hardware provided and a quality Phillips head
screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
NOTE:
SAVE THESE
INSTRUCTIONS
Safety Information (continued)

5
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Warranty
1 Year Limited Warranty: The manufacturer warrants that your new Electric Fireplace is free from manufacturing and material defects for
a period of one year from date of purchase, subject to the following conditions and limitations.
1. Install and operate this appliance in accordance with the installation and operating instructions furnished with the
product at all times. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify
this warranty.
2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made through
an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship,
provided that such part(s) have been subjected to normal conditions of use and service, after said defect is conrmed
by the manufacturer’s inspection.
4. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding
the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s),
repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume
responsibility for same.
6. The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential loss or
damage arising out of the use, or inability to use the product, except as provided by law.
7. All other warranties – expressed or implied – with respect to the product, its components and accessories, or any
obligations/liabilities on the part of the manufacturer are hereby expressly excluded.
8. The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other liabilities with
respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non-accessories used in conjunction with the
installation of this product.
10. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
This warranty is void if:
a. The replace is subjected to prolonged periods of dampness or condensation.
b. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.
Warranty

6
HARDWARE INCLUDED
JJ KK LL MM NN OO PP QQ RR SS
Part Description Part Number Quantity
AA Wood Dowel PH-DWLNTL001 25
BB Shelf Pin PH-SPNPCSPLB2 8
CC Knob (with Screw) N/A 4
DD Bolt 6.3 x 12 mm PH-BLTBK002 39
EE 2 Hole Plastic Connector Block PH-PCBBLK001 18
FF 3 Hole Plastic Connector Block PH-PCBBLK002 1
GG Magnetic Catch PH-MCHBRW001 2
HH Screw 3 x 15 mm PH-SCRBLK010 4
II Screw 4 x 50 mm PH-SCRBLK006 16
JJ Screw 4 x 25 mm PH-SCRBLK018 8
KK Screw 3.5 x 12mm PH-SCRBLK013 8
LL Screw 3x16mm PH-SCRBLK001 36
MM Screw 4x15mm PH-SCRBLK009 2
NN Pin Hinge PH-HNGBLK001 4
OO Bracket PH-BKTBLK007 2
PP Tipping Restraint PH-BKTWHT003 2
QQ Metal Plate (pre-attached) PH-PLTBLK001 2
RR Leveler (pre-attached) PH-LVRBLK001 1
SS Floor Glide (pre-attached) PH-GLDBRW001 4
Phillips Screwdriver
NOTE:
Hardware not shown to actual size.
PRODUCT SPECIFICATIONS
VOLTAGE 120VAC, 60 Hz
AMPS 12.5 Amps
WATTS 1500 Watts
PLANNING ASSEMBLY
Before beginning assembly of product, make sure all parts are present. Compare parts with Hardware Included and Package Contents lists.
If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement
parts.
Estimated Assembly Time: 60 Minutes
TOOLS REQUIRED
Pre-Assembly
II
DD
CC EE FF GG HH
AA BB

7
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Part Description Quantity
A Bottom Base Panel 1
B Center Shelf Front Panel 1
C Left Front Panel 1
D Right Front Panel 1
E Left Center Panel 1
F Right Center Panel 1
GTop Assembly 1
H Center Shelf 1
I Left Side Panel 1
J Right Side Panel 1
K Left Decorative Front Panel 1
L Right Decorative Front Panel 1
M Foot 1
N Divider 1
OTop Apron 1
P Side Back Panel 2
Q Center Back Panel 1
R Left Side Door 1
S Right Side Door 1
T Adjustable Shelf 2
U Fireplace Insert 1
PACKAGE CONTENTS
NOTE: All panels are labeled left
and right as viewed from the front of
unit.
Pre-Assembly (continued)
J
A
C
D
F
H
O
G
E
I
P
P
Q
R
S
L
N
M
B
T
T
K
U

8
3 4
Using the Left Front Panel (C) and the Left Center
Panel (E), align the previously installed Wood Dowels
into the holes.
Secure by tightening the Screws (II) through the
pre-drilled holes.
Repeat step for the Right Front Panel (D).
Preparing the front panels
Align the previously installed Wood Dowels in
the Center Shelf Front Panel (B), with the Left
Front Panel (C) and Left Center Panel (E). Push
them together.
Repeat to attach the Right Front Panel (D).
Attaching the upper front panel
Place the Center Shelf Front Panel (B), Left Front Panel
(C) and Right Front Panel (D) on a at surface.
Insert Wood Dowels (AA) into the pre-drilled holes as
shown.
Continue until all Wood Dowels (AA) are secured on the
Center Shelf Front Panel (B), Left Front Panel (C) and
Right Front Panel (D) as shown.
Place the Left Center Panel (E) and Right Center Panel
(F) on a at surface.
Attach the 2 Hole Plastic Connector Block (EE) to both
Panels (E,F) as shown.
Secure the Blocks using the Bolts (DD).
1Preparing the front panels 2Preparing the center panels
Assembly
B
E
EE
DD
F
AA
B
C
D
E
F
D
C
EC
II
D
F

9
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Put the Center Shelf (H) upside down on a at surface.
Secure the Magnetic Catch (GG) using the Screws (HH).
5Preparing the center shelf
Using the Phillips Screwdriver, attach the 2 Hole Plastic
Connector Block (EE) to the Center Shelf (H) with
Bolts (DD).
6Preparing the center shelf
Assembly (continued)
Align the Left Center Panel (E) and the Right Center
Panel (F) with Center Shelf (H).
To secure the panels to the Center Shelf (H), insert the
Bolts (DD) through the 2 Hole Plastic Connector Block
(EE).
Tighten Bolts (DD) with the Phillips screwdriver.
7Attaching the panels
H
H
H
E
F
GG
HH
EE
DD
DD
EE

10
Using the Phillips screwdriver, insert screws (II) through
the pre-drilled holes on the Center Shelf Front Panel (B)
and tighten the Screws (II).
Put the Left Side Panel (I) on a at surface.
Insert the Bolts (DD) through the 2 Hole Plastic
Connector Block, using the Phillips screwdriver.
Repeat step for the Right Side Panel (J).
8
10
9
Securing the center panels Preparing the side panels
Align the Left Side Panel (I) and the Left
Decorative Front Panel (K).
Insert the Bolts (DD) through the 2 Hole
Plastic Connector Block (EE), using the
Phillips screwdriver.
Repeat for the Right Decorative Front
Panel (L).
Attaching the decorative front panels
Assembly (continued)
II
DD
J
J
DDEE
I
K
L
I
EE
B

11
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
11
12
Attaching the side panels
Preparing the center assembly
Insert Wood Dowels (AA) into the pre-drilled holes as shown
below.
Assembly (continued)
Align the Left Side Panel (I) with the Center Shelf (H).
To secure, insert the Screws (DD) through the
previously attached 2 Hole Plastic Connector Block (EE).
Tighten Bolts (DD) with the Phillips screwdriver.
Repeat step to attach the Right Side Panel (J).
I
J
J
F
E
I
H
DD
AA
EE

12
To secure the Foot (M) to the Bottom Base Panel (A),
insert the Screws (JJ) through the pre-drilled holes.
Tighten the Screws (JJ) with the Phillips screwdriver.
Place the Divider (N) on a at surface.
Attach the 3 Hole Plastic Connector Block (FF) using the
Bolts (DD) and the Phillips screwdriver.
Align the Bottom Base Panel (A) with previously
assembled Panels (I,E,F,J).
Secure together using the Screws (II) and the Phillips
screwdriver.
13
15
14
Attaching the foot
Preparing the Divider
Attaching the base
Assembly (continued)
A
M
JJ
A
IE
F
J
II
FF
N
DD

13
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Stand the assembled section up right.
Insert a Wood Dowel (AA) into the pre-drilled hole
in the Center Shelf (H).
Align the Divider (N) to the Center Shelf (H) and
secure together using the Screws (II) and a
Phillips screwdriver.
16 Preparing the center shelf
18 Attaching the top apron
Insert the Screw (LL) through the Metal Plate (QQ) to
secure the Top Apron (O) to the Right Decorative Front
Panel (L).
Repeat step to secure the Top Apron (O) to the Left
Decorative Front Panel (K).
17 Attaching the divider
Assembly (continued)
AA
H
H
II
LL
QQ O
L
K
N

14
19 20
Preparing for the top of
the assembly Attaching the top assembly
Insert Wood Dowels (AA) into the pre-drilled holes in
the Top Apron (O).
Place the Top Assembly (G) on top of the main
assembly.
From underneath, insert the Bolts (DD) through
the Plastic Connectors (EE,FF).
Tighten using a Phillips screwdriver.
Assembly (continued)
Insert the Screws (JJ) into the pre-drilled holes in the
Top Apron (O).
21 Securing the top assembly
AA
DD
G
AA
FF
JJ
GO
EE
O

15
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Insert the Screws (LL) through the pre-drilled holes in
the Center Back Panel (Q) and the Side Back Panels (P).
Tighten using a Phillips Screwdriver.
22
23
Installing the back panels
Attaching the knobs
Insert the screws through the pre-drilled holes in the
Right Door (S), to attach the Knob (CC).
Repeat for the Left Door (R).
Q
P
P
LL
Assembly (continued)
CC
S
R

16
24 25
Attaching the doors Attaching the adjustable shelves
Insert the Pin Hinge (NN) into the pre-drilled holes in
the Bottom Base Panel (A) and the Center Shelf (H).
Align the Left Side Door (R) with the Pin Hinge (NN).
Secure the Left Side Door (R) with the Screws (KK).
Repeat for the Right Door (S).
Insert the Shelf Pins (BB) into the pre-drilled holes
on the inside of the Left Side Panel (I) and the Left
Center Panel (E).
Rest the Adjustable Shelf (T) on the Shelf Pins (BB).
Repeat for the right side.
Assembly (continued)
NN
KK
A
S
TI
E
BB
T
R
H
Lift the Fireplace Insert (U) carefully into the back of the
unit and center in the replace insert opening.
Do not drag the replace insert across the Base
as it may scratch your unit.
26 Installing the replace insert into
the mantel assembly
U

17
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Insert the Screws (MM) through the Bracket (OO) into
the pre-drilled holes in the Bottom Base Panel (A).
To level your assembled media unit, turn the Leveler
(RR), as needed.
The pre-attached Leveler (RR) is located under
the Foot (M).
27
28
Securing the replace insert
Leveling the assemebled unit
U
A
MM
OO
Assembly (continued)
M
RR

18
29
PP
G
When the Tipping Restraint Hardware (PP) is properly
installed, it can provide protection against unexpected
tipping of the Unit due to small tremors, bumps
or climbing.
Your Unit comes with two Tipping Restraint Hardware
(PP). Each Tipping Restraint Hardware (PP) includes
one Unit Anchor, one Wall Anchor, one Anchor Tether,
and four Anchor Screws. Use these to complete the
following steps for a proper installation.
Locate a secure wall stud behind the unit closest to
left side.
Align the Unit Anchor with a wall stud and attach with
two Anchor Screws using a Philips Head Screwdriver.
The Anchor Screws must pass through the Top
Assembly (G) for proper installation.
Align the Wall Anchor in the center of the wall stud, at
level with the Unit Anchor, and attach with two Anchor
Screws using a Philips Head Screwdriver.
On the Anchor Tether, detach the cable from the
connector and loop the loose cable through the eyelets
on the Wall Anchor and Unit Anchor. Reattach the loose
cable to the connector, but do not tighten.
Locate a secure wall stud behind the unit closest to the
right side, and repeat the steps above.
Tighten both Anchor Tethers by pulling the cable
the through connector.
Wall
Installing the tipping restraint hardware
WARNING:
Installing the Tipping Restraint
Hardware will help prevent accidents or damage to the
unit.
NOTE:
Installation of the Tipping Restraint Hardware
(PP) will provide a small space between the wall and the
unit. This will allow you to run power cords and connector
cables to your television or other devices placed on top of
the Unit.
Assembly (continued)

19
HOMEDEPOT.COM/HOMEDECORATORS
Please contact 1-800-986-3460 for further assistance.
Operation
Operation
3 4
Adjusting the heater
Press the Heater button to set the thermostat. The replace
contains three infrared quartz heating elements.
The thermostat setting range is 62°F - 82°F or 17°C - 27°C
or always ON.
The thermostat is adjustable by 2°F or 1°C increments.
The up and down buttons“ ”on the remote will
increase / decrease temperature setting.
NOTE: To change between °F and °C press and hold the
HEATER button on the control panel for 3 seconds.
Push the Power button to supply power to all
functions of the replace and put the insert in a
standby mode.
Push the Power button again to turn off all functions.
1 2
Powering the replace
NOTE: Holding the Power button on the control panel for
10 seconds will disable the heater function.
NOTE: All previous settings are held in memory, so the
next time you power up the replace, the unit will turn on
with the same settings.
Adjusting the ame
There are 6 brightness levels that can be selected:
Settings F6 - F4 decrease in Amber brightness
Settings F3 - F1 decrease in Spectrare brightness
Pressing the Timer button will cycle through the timer
settings; 30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H, 7H,
8H, 9H and off.
Setting the timer
NOTE: The control panel can be accessed at the upper-right corner of the insert.
/

20
NOTE: Please operate the remote control at a slow
measured pace. Press the remote control buttons with
an even motion and gentle pressure. Repeatedly pressing
buttons in rapid succession may cause the transmitter to
malfunction.
NOTE: Do not mix old and new batteries. Do not mix
alkaline, standard (carbonzinc), or rechargeable (nicad,
nimh, etc) batteries. Do not ingest batteries.
Operation (continued)
When the remote control stops operating or its range
seems reduced, it is time to replace the battery with
new ones.
On the back end of the remote, press and slide
the battery door open and remove the old battery.
Insert 2 AAA batteries, checking that the + and -
sides of the battery match inside the battery
compartment.
Replace the battery compartment door.
The battery may contain hazardous substances that
could endanger the environment and human health.
This symbol marked on the battery and/or packaging
indicates that used battery shall not be treated
as municipal waste. Instead it shall be left at the
appropriate collection point for recycling.
By correctly disposing used batteries, you prevent
potential negative consequences for the environment
and human health. Recycling used materials also
conserves natural resources.
For more information about collecting and recycling
used batteries, please contact your local municipality,
your waste disposal service or the point of sale where
you purchased this product.
5 6
Replacing the remote control battery Disposing of used batteries
7Power cord information
This heater is for use on 120 volts. The cord has a plug
as shown in the figure.
Connect to properly grounded outlets only.
Do not use a 2 prong adapter. Never use with an
extension cord or relocatable power tap (outlet/
power strip).
NOTE: Batteries should be removed if the product is
to be left unused for a long time.