Home Decorators Collection DYLAN 60 User manual

PAGE 1
DYLAN 60
GBSH167 / GBSH170 / GBSH175
INSTALLATION MANUAL
2023-07-25 HOMEDEPOT.COM/HOMEDEPOT.CA/HOMEDECORATORS
Questions, problems, missing parts?
Before returning to the store, call Home Decorators Collection customer service department at
1-800-986-3460, 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday.
An installation video guide can be found on our Youtube channel:
https://tinyurl.com/5x9n6z4k

PAGE 2
CAUTION
Please carefully read the following important safety information before handling or installing this shower. There is a
risk of serious injury while handling this product. To minimize these risks, please note:
• Always wear safety glasses and gloves while handling.
• Always read and follow all the steps in the installation instructions.
• Inspect all contents and glass for damage before installation.
• Keep the corner protectors on glass panels until the installation is nished.
• Extreme caution should be taken while handling the glass during installation as the tempered glass may shatter if
in contact with a hard surface.
• Handle the tempered glass with caution! Improperly handling the glass can cause it to break suddenly in small
pieces (never in pointed fragments).
• Always take all precautions not to touch the tempered glass with any tools during the installation, or after installed.
• Do not cut or modify the tempered glass as it will shatter if cut.
• Carefully remove product from packaging and keep packaging until installation is complete.
• Inspect all parts for damage; if there is damage to the unit prior to installation, please contact customer service at
the number provided in this guide.
• Install the shower on a oor that is level and able to accommodate the weight of the unit and an occupant.
• Consult local building codes and compliance standards prior to installation and ensure conformity.
• After installation, and from time to time, check the glass for t and nish to ensure that nothing has come loose
since installation.
• Keep this installation manual for future reference.
SAFETY INFORMATION
NOTICE
Any modication or alteration from what is specied in this instruction manual will void any and all warranty on this
product.
The distributor is not responsible for any damage to the unit or personal property caused by improper installation. If
you disregard instructional warnings, you will void your warranty and possibly deal with water damage.
Consult the distributor’s website for any additional information or question on this product’s installation.
SAFETY NOTICE
PREPARATION
You will need at least two people to install this unit properly.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

PAGE 3
SHOWER DIMENSIONS
C
28 11/16 in D
31 7/8 in
A
76 in
E
24 5/8 in
F
13 1/8 in
*B*
55 15/16 in~60 1/16 in
A
76 in
Measures: inch
Measurements
AShower height
*B* Shower width
CFixed panel width
DDoor panel width
EDoor opening
FDistance between handle holes
*B*
ATTENTION!
This is the required shower space
measurement to install the shower.

PAGE 4
WALL-TO-WALL DIMENSIONS
WARNING!
**If you require to cut the bar, refer to the calculation below:
1. Measure the distance “D” at the height where the bar will be installed.
2. Cut the bar to a total length of L = D - 7/8 in.
3. The maximum measure to cut from the bar should be no more than 2 9/16 in.
76 in
L
L = D - 7/8 in
D
• Measure the thickness of your nished surface on either side before installing the metal tracks.
• Make sure to have a nished surface distance (D) between the min and max permissible dimensions according to the table
below.
*IMPORTANT: Your shower is designed to accommodate a 1 9/16 in tolerance from the maximum value. If needed you
can cut the support bar to t the shower.
FINISHED SURFACE OPENING (D) SHOWER DOOR HEIGHT
(Make sure the door height is not surpassing your tile /
acrylic wall height)
Support bar adjustability
MIN** MAX*
55 15/16 in 60 1/16 in 76 in

PAGE 5
PACKAGE CONTENT
B
x1
D
1x
K
2x
C
1x
G
2x
H
2x
I
1x
L
1x
F
1x
J
1x
E
2x
A
1x
Sliding door guide
(with its rubber tting)
Chrome: 99SGC1053-WM
Brushed Nickel: 99SGC4081-WM
Matte Black: 99SGC4161-WM
Wall track
Chrome: 99STR-5M64HR89-WM
Brushed Nickel: 99STR-KL87YSV0--WM
Matte Black: 99STR-M926W99X-WM
Support bar anchor
Chrome: 99SGC-5D4737L9-WM
Brushed Nickel: 99SGC-ASU15085-WM
Matte Black: 99SGC-U6ZVJ8L0-WM
Door anti-jump peg
Chrome: 99SGC-W013F105-WM
Brushed Nickel: 99SGC-X76ZP1EO-WM
Matte Black: 99SWE-11ORL4GY-WM
Support bar
Chrome: 99SGS-O16O1HTE-WM
Brushed Nickel: 99SGS-HO65XO63-WM
Matte Black: 99SGS-V3LOOZFZ-WM
Glass panel vertical seal strip
Transparent: 99SRU0026
Matte Black: 99SRU3794-WM
Door roller
Chrome: 99SWE0009-WM
Brushed Nickel: 99SWE0013-WM
Matte Black: 99SWE3616-WM
Door panel vertical seal strip
Transparent: 99SRU0027
Matte Black: 99SRU3795-WM
Door panel
99SGD-2W0OAH42-WM
Decorative cap
Chrome: 99SGC4105-WM
Brushed Nickel: 99SGC4106-WM
Matte Black: 99SHW6134-WM
Decorative track
Chrome: 99STR3801-WM
Brushed Nickel: 99STR3802-WM
Matte Black: 99STR3940-WM
Fixed panel
Chrome: 9SGP-L862G6J0-WM
Brushed Nickel: 99SGP-42T5UGZ2-WM
Matte Black: 99SGP-9GXX30O2-WM
N
1x
M
1x
O
1x
P
1x
Door handle
Chrome: 99SHA-4TE02J82-WM
Brushed Nickel: 99SHA-66ZC1UBE-WM
Matte Black: 99SHA-U76R86TO-WM
Fixed panel bottom seal strip
Transparent: 99SRU3683-WM
Matte Black: 99SRU3955-WM
Door bottom seal strip
Transparent: 99SRU3684-WM
Matte Black: 99SRU3956-WM
Support bar anchor
Chrome: 99SGC0038-WM
Brushed Nickel: 99SGC4006-WM
Matte Black: 99SGC4938-WM
Complete hardware kit (refer to next page)
Chrome: 99SHW-OAP76UD8-WM
Brushed Nickel: 99SHW-T75062QG-WM
Matte Black: 99SHW-5I0AS9V4-WM

PAGE 6
SUPPLIED HARDWARE LIST
CC FFEEAA
GG
BB
Screw
ST4x20mm
2+1
Wall Anchor
ø8x30mm
5+1
Screw
ST5x40mm
2+1
Cap
3x
Fitting
3x
Screw
ST5x30mm
3+1
DD
Screw
ST4x12mm
3+1
HH
Cap
2x
Allen key
2.5mm & 4mm & 5mm
II JJ
Cap
2x
Cap
2x
Cap
1x
KK
TOOLS REQUIRED (not supplied)
Pencil Screwdriver Drill and drill bits
ø1/8 in & ø5/16 in
LevelMeasuring Tape Silicone Rubber mallet
Cutter
Safety glasses Ratchet
3/16 in Bit socket
Glass suction cup

PAGE 7
DOOR ASSEMBLY OVERVIEW
F
P
B
E
C
I
M
N
A
O
J
K
L
D
G
H

PAGE 8
BEFORE INSTALLATION
For the easy installation of this shower please read the following important points:
• READ ALL the instructions completely before beginning.
• Make sure your walls are within 3/8 in of plumb. And wall corners should meet at 90oas illustrated.
• Make sure your tub or shower base is level.
• When using Solid Polymer Composite (SPC) shower walls, dry t your shower door and make sure there is a stud where the
wall track will be installed.
Please see the images below for Alcove shower.
90o
90o
LEVEL
LEVEL
90o
LEVEL
LEVEL
90o

PAGE 9
A B
PREPARATION
This instruction is drawn up for a door opening from right to left (see illustration A).
For an installation for a door opening from left to right (see illustration B), use the same
instructions, but switch around the panels: mirror e󰀨ect.
FAQ
Q: If the shower head is installed
on the other wall, will it leak?
A: It is possible to install your
shower head on the other side,
but we strongly recommend to
install it as illustrated.
Install the shower head on the door’s side as shown in the illustration!
This will reduce the risk of leaking.
DOOR DOOR
FIXED
PANEL
FIXED
PANEL
RIGHT DOOR
OPENING
LEFT DOOR
OPENING

PAGE 10
WALL TRACK INSTALLATION
1.1-1.2. Position the wall track (B) as illustrated. Level the track (B) and mark the track holes positions.
1.3. Remove the track and drill pilot holes in the marked locations with a ø5/16 in drill bit.
1.4. If there are no studs located behind the wall track (B), then insert the wall anchors (AA) using a rubber mallet until the wall
anchors are ush with the wall.
1.5. Replace and secure the track (B) with screws (BB). Do not overtighten.
1
13/16 in
B
ø5/16 in
BB
1.1
1.2
1.3
1.5
AA
1.4
WARNING!
If there are no studs aligned
to the wall track behind the
drywall, use the wall anchors
to ensure the screws won’t
become loose.
B
B
AA
B
B
BB
RIGHT DOOR OPENING
LEFT DOOR OPENING

PAGE 11
FIXED PANEL AND SUPPORT BAR INSTALLATION
2.1. Insert the xed panel bottom seal strip (N) on the base of the xed panel (C). Cut the surplus part with a cutter, about 1 9/16
in from the panel’s edge.
2.2. Insert the xed panel (C) into the wall track (B). Do not fully tighten it as further adjustments may be required.
Note: The wall track (B) allows you to adjust the position of the xed panel (C). Adjusting the depth and/or giving the
glass panel a slight angle allows for out of plumb adjustment.
2.3. Smoothly slide the sliding door guide (A) at the bottom of the xed panel (C), but without securing it.
2
1 9/16 in
B
C
N
CC
A
2.1 2.3 2.2
C
N
B
C
N
B
LEFT DOOR OPENINGRIGHT DOOR OPENING
A A

PAGE 12
NEXT STEP MAY REQUIRE TO TRIM THE SUPPORT BAR
If the support bar is too long for your wall-to-wall opening “D”, you will have
to trim it down. Below calculation is for reference only: Ensure you made all
the proper measurements before you cut the bar.
1. Measure the distance “D” at the height where the bar will be installed.
2. If D < 58 7/16 in, cut the bar to a total length of L = D - 7/8 in.
D
1
L = D - 7/8 in
2
L
26 5/8 in

PAGE 13
FIXED PANEL AND SUPPORT BAR INSTALLATION
3.1. Install the support bar anthors (D & P) onto the support bar (F).
3.2. Loosely mount the support bar (F) onto xed panel (C) using the bracket and level it.
3.3. Mark the position of the guide (A).
3
D
3.1 3.2
FP
C
A
3.3
F
C
26 5/8 in
26 5/8 in
WARNING!
Ensure shorter end of support
bar connected to the xed
panel.
WARNING!
Ensure shorter end of support
bar connected to the xed
panel.
26 5/8 in
D D
F F
P P
C C
A A
LEFT DOOR OPENINGRIGHT DOOR OPENING

PAGE 14
BC
FIXED PANEL AND SUPPORT BAR INSTALLATION
4.1-4.2. Place the support bar (F) in order to align the bracket in front of the xed panel’s hole. Position the support bar so that
the A and B measurements in illustration 4.1 below match the A and B measurements in illustration 4.2 respectively. Mark the
outline of the 2 support bar’s anchors (D & P) on the wall.
4.3. Completely remove the support bar (F).
4.4. Completely remove the xed panel (C).
4.5. Mark the positions of holes of the sliding door guide (A).
4
C
4.1 4.2
F
C
4.4
4.3
FD & P
F
C
B
A
B
A
A
4.5
B

PAGE 15
FIXED PANEL AND SUPPORT BAR INSTALLATION
5.1. Drill a pilot hole for the sliding door guide (A) using a ø1/8 in drill bit.
5.2. Install the sliding door guide (A) with the screw (CC) and the cap (HH).
5.3. Place the 2 support bar anchors (D & P) back on their wall mark, then mark their center on the wall.
5.4-5.5. Drill a hole on the center marks with a ø5/16 in drill bit . If there are no studs located behind the support bar anchors (D
& P), then insert the wall anchors (AA) using a rubber mallet until the wall anchors are ush with the wall. Fix the center tting of
the support bar anchors (D & P) on the wall using the screws (GG).
5
D
A
HELPFUL HINT!
Add a drop of silicone in the
holes before inserting the
screws.
HH
CC
5.1 5.2 5.3
5.4 5.5
ø5/16 in
ø1/8 in
WARNING!
If there are no studs aligned to support bar
anchors behind the drywall, use the wall
anchors to ensure the screws won’t become
loose.
P
GG D
PGG
D D
P P
A A
LEFT DOOR OPENINGRIGHT DOOR OPENING
B B

PAGE 16
FIXED PANEL AND SUPPORT BAR INSTALLATION
6.1. Install the support bar anthors (D & P) onto the support bar (F).
6.2. Insert the door bottom seal strip (O) onto the door panel (J).
6
WARNING!
Before continuing, place the
door panel (J) inside the shower
enclosure to facilitate future
steps!
6.2
J
O
D
6.1
F
P
B

PAGE 17
BC
FIXED PANEL AND SUPPORT BAR INSTALLATION
7.1-7.2. Place the xed panel (C) into the wall track (B) and put back the sliding door guide (A).
7.3-7.4. Fix the xed panel (C) onto the support bar (F) using the bracket, then install the cap (KK) onto the bracket. Secure the
support bar (F) on it’s anchors (D & P) using the provided hex screws.
7
7.1
7.4
D & P
A
C
7.2
7.3
F
C
KK F
B B
C C
A A
F F
D D
P P
RIGHT DOOR OPENING LEFT DOOR OPENING

PAGE 18
C
A
J
SHOWER DOOR INSTALLATION
8.1. Install the 2 door rollers (H) on the door panel (J).
8.2-8.3. Gently hang the door panel by its 2 rollers (H) on the support bar (F) and make sure to place the bottom of the door
inside the guide (A).
8
8.28.1
H
JJF
H
8.3
H H
J J
H H
F F
A A
RIGHT DOOR OPENING LEFT DOOR OPENING

PAGE 19
LEVELING THE GLASS PANEL
After the wheels have been installed, adjust the level of the glass panel using the eccentric mechanism of the rollers. Insert
the smaller allen key in the hole on the side of the roller, then use the bigger allen key to slightly loosen the roller by turning it
counter clockwise. Rotate the roller clockwise using the smaller allen key to raise the glass. To lower the glass, rotate the roller
counter clockwise using the smaller allen key. After the adjustment is done, using the smaller allen key to hold roller rotation,
while turning the bigger allen key clockwise carefully
9
HELPFUL HINT!
When the eccentric backside of the wheel is in
this position, it has reached the “highest” glass
position.
HELPFUL HINT!
When the eccentric backside of the wheel is in
this position, it has reached the “lowest” glass
position.
1 2
1 2

PAGE 20
SHOWER DOOR INSTALLATION
Important: Once the door is adjusted correctly, only then resume to the next step.
10.1. Install the 2 anti-jump pegs (E) on the door panel (J). Use a ratchet to strongly tighten the bolts.
10.2. Install the caps (II & JJ) onto the door rollers (H) and anti-jump peg (E).
10
10.1
H
E
II
JJ
H
10.2
H
EH
E
E