Home Decorators Collection SW19110 BN User manual

BRITTON LED 52 IN. CEILING FAN
SKU/Model : #XXXX/#SW19110 MWH
#XXXX/#SW19110 MBK
#XXXX/#SW19110 BN
TBA

52 in.
XXX XXX XXX XXX
XXX XXX XXX XXX
XXX XXX XXX XXX
xxx xxx
xxx xxx xxx
We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period
of lifetime after the date of purchase by the original purchaser. And we warrant the LED light kit to be free from defects in workmanship
and material present at time of shipment from the factory for a period of 5years after the date of purchase by the original purchaser.
We also warrant that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the
time of shipment from the factory for a period of 2 years after the date of purchase by the original purchaser. We agree to correct such
defects without charge or at our option replace with a comparable or superior model if the product is returned. To obtain warranty service,
you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility.
Damage to any part such as by accident, misuse, improper installation or by affixing any accessories, is not covered by this warranty.
Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding,
tarnishing or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain
amount of "wobble" is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the
warranty invalid. There is no other express warranty. We hereby disclaim any and all warranties, including but not limited to those of
merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be
disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you. The retailer shall not be liable for incidental, consequential, or special
damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do
not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty
givesd specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior
warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.
Ladder

Fiber washer
15+1 spare
15+1 spare
Flywheel screw
5+1 spare
Remote control holder mounting screw
3
Mounting plate screw (pre-assembled) 4
Fan housing screw (pre-assembled) 4

Fan blades
3
Fan housing
Fan motor assemby
Flywheel
21W LED assembly
Mounting plate (pre-assembled)
Receiver with extension wire
(pre-assembled)

B
D
JJ
B
JJ
II
II
II
GG
KK
F
II
GG
Remove the mounting plate screw (GG) from the mounting
bracket (B) and loosen the other three mounting plate
screws (GG) approximately 1/4 turn. Keep the mounting
plate screw (GG) that removed aside for use later.
Lift the fan motor assembly (F) by hanging the square hole
(KK) of the mounting plate (D) on the hook (JJ) from the
mounting bracket (B) allowing it to hang.

Electrical connections
Connect the ground wire (green or bare copper) of
the outlet box to the ground wire of the mounting
plate (D) and the ground wire of the mounting
bracket (B).
1
LL
D
E
B
Note: For easy installation, the receiver (E) with extension
wire (LL) is pre-intalled on the mounting plate (D).
wire nuts (DD)
receiver (E).
receiver (E).

Installing the fan motor assembly
Lift and place the key holes (MM) of the mounting plate (D)
over the three screws (GG) previously loosened on the
mounting bracket (B) and turn the mounting plate (D) until
it locks in place and no longer turns.
Secure by tightening the three screws (GG) previously
loosened and the screw (GG) previously removed.
WARNING: Ensure you complete this step correctly
and follow all steps. Failure to correctly follow this
step might cause the fan to fall.
B
F
MM
B
F
GG
D
GG
D
GG

Align the four large screws (HH) pre-locked on the fan housing (C) to the slotted holes (NN) of the mounting bracket (B).
Turn the fan housing (C) at the right side and twist the screws (HH) to the end of the slotted holes (NN) until
they lock in place and no longer turn.
Installing the fan housing
HH
C
B
F
NN

Tighten the flywheel (G) onto the bottom of fan motor assembly (F) by using the five flywheel screws (CC).
C
F
E
CC
flywheel

Insert the blade (A) through the slot on the flywheel (G). Fasten the fan blade (A) to the flywheel (G) by using
the three blade screws (AA) and the three fiber washer (BB) and tighten them securely. Repeat this step for the
other four blades.
C
F
AA
BB
Installing the fan blades to the flywheel
A

OO
OO
H
CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan
Before Installing The Light Kit.
F
Attach the LED assembly (H) to the locking plate (PP) of fan motor assembly (F) by twisting tightly.
PP
H

I
I
K
K
QQ
15
14
reverse button (QQ):
Note: To operate the reverse function on this fan, press the reverse button when the fan is running.

J
J
EE

Check the wires with the molex plugs to ensure proper connection.
Balancing kit included
additional instruction manual within the packet.
9

Fan blades
Fan housing
Fan motor assemby
Flywheel
21W LED assembly
Mounting plate (pre-assembled)
Receiver with extension wire
(pre-assembled)
Fiber washer
Flywheel screw
Remote control holder mounting screw
Mounting plate screw (pre-assembled)
Fan housing screw (pre-assembled)

CF552HR-01