Home Decorators Collection Oxford BF-20429 User manual

1/11
BF-20429 Oxford Collection 3 drawer Letter Size file Cabinet
ASSEMBLY INSTRUCTIONS
Made In China

numbered to assure fast,easy and correct assembly.
Follow instructions listed below in proper sequence as
efficient and speedy service please indicate the model number and
or damaged,phone,fax,or mail to our Customer Service Department.For
DRAWER PANEL SIDES-3PCS
LOW PANEL-1PC
LEFT
J
TOP PANEL-1PC
BOTTOM PANEL-1PC
G
D
IMPORTANT NOTE:
A
2/11
DRAWER PANEL BACKS-3PCS
DRAWER PANEL FRONTS-3PCS
PARTS LIST
RIGHT SIDE PANEL-1PC
ACROSS PANELS-2PCS
K
H
E
B
RIGHT
DRAWER PANEL SIDES-3PCS
DRAWER PANEL BOTTOMS-3PCS
L
BACK PANEL-1PC
LEFT SIDE PANEL-1PC
I
F
C
material carefully for small parts,which may have came loose inside the
with parts list to be sure all part are present.If any parts are missing
carton during shipment. Count all parts and material hardware,Compare
Thank you for purchasing this quality product.Be sure to check all packing
code letter of part(s)need.

3/11
Z1
W1
REMARK:THE LETTER STICKED IS THE BACK SIDE.
INNER SLIDES-6PCS
W
T
Q
FILE HANGERS-6PCS
to prevent tipping
to prevent tippingto prevent tippingto prevent tipping
SCREWS-2PCS
Y1
HANGERS-2PCS
X1
SCREWS-2PCSHOOKS-2PCS
SCREWS-24PCS
CAM-TOOL-1PC
Y
V
S
KNOBS-3PCS
CAM-LOCKS-12PCS
DOWELS-20PCS SCREWS-18PCS
SCREWS-3PCS
U
CAM-BOLTS-12PCS
R
SCREWS-36PCS
OUTER SLIDERS-6PCS
Z
MP
N

HOW TO SEPARATE GLIDES
4/11
PRIOR TO ASSEMBLY,WE SUGGEST SEPARATING THE INNER GLIDES FROM THE OUTER-GLIDES,
SIMPLY PULL THE LEFT/RIGHT INNER GLIDES FROM THE OUTER GLIDES EXPOSING A SMALL
Z
SAFETY RELEASE TAB
W
BLACK SAFELY RELEASE TAB,BY PUSHING THE SAFETY RELEASE TAB.YOU WILL BE ABLE TO
SEPARATE THE GLIDE.

TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE ASSEMBLE THIS ITEM WITH AT
HOW TO USE THE CAM-TOOL
SHOULDER
LEAST TWO PEOPLE.
NOTE:
MN
ARROW
5/11
NOTE:
AGAINST THE SURFACE OF THE PART.
TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
ARROW
UPON OPENING THOROUGHLY CLEAN ALL WOODS SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT.IN ORDER
NOTE:
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS.

INSERT THE DOWELS(Q)INTO HOLES IN BACK DRAWER PANEL(K)AND ATTACH USING SCREWS(P).
INSERT DOWELS(Q)INTO HOLES IN PANEL(H)AND ATTACH SIDE PANELS(I/J)USING SCREWS(P).
6/11
1).ASSEMBLE THE DRAWER.
FINALLY,ATTACH INNER SLIDES(W)TO DRAWER PANEL SIDES(I/J)USING SCREWS(V).
INSERT THE FILE HANGERS(U)INTO THE CUT-OUT OF DRAWER PANEL FRONT&BACK.
INSERT BOTTOM DRAWER PANEL(L)INTO SLOT IN SIDE DRAWER PANELS(I/J).
ATTACH THE KNOB(S)TO FRONT DRAWER PANEL(H)USING SCREWS(T).

7/11
INSERT THE DOWELS(Q)INTO DESIGNATED HOLES ON PANELS(E/G).
ROTATE THE 8 CAM-BOLTS(N)INTO HOLES IN SIDE PANELS(B/C).
PLACE THE CAM-BOLTS(N)INTO HOLES IN PANELS(E/D)AND ATTACH USING CAM-LOCKS(M).
E
C
Q
G
N
D
M
2).ASSEMBLE THE SIDE PANEL(B/C).
E
B

ROTATE THE 4 CAM-BOLTS(N)INTO HOLES IN TOP PANEL(A).
PLACE THE CAM-BOLTS(N)INTO HOLES IN SIDE PANELS(B/C)AND ATTACH USING
ATTACH THE OUTER SLIDES(Z)TO SIDE PANELS(C/B)USING SCREWS(V).
3).ASSEMBLE THE TOP PANEL(A).
CAM-LOCKS(M).
N
8/11
M
A
Z
V

9/11
SLIDE THE DRAWER INNER SLIDES INTO OUTER SLIDES.
4).ASSEMBLE THE DRAWERS.
NOTE:ALL DRAWER WILL BE ATTACHED TO THE SLIDES AS DESCRIBED BELOW.

10/11
ATTACH BACK PANEL(F)USING SCREWS(R)INTO THE REAR OF SIDE,TOP,AND BOTTOM PANEL.
F
R
5).ASSEMBLE THE BACK PANEL(F).

DRILL TWO HOLES INTO WALL,PLEASE REFER TO THE REAR TOP PANEL'S HOLE DISTANCE AND
HEIGHT.
W1
X1
11/11
Z1
PREDRILLED HOLES OF REAR TOP PANEL.
Y1
ATTACH 2 HOOKS(W1)USING 2 SCREWS(X1)IN THE
wall
floor
Warning
The anti-tip hardware must be used as part of assembly!
PUT 2 HANGERS(Y1)INTO HOLES IN WALL AND ROTATE 2 SCREWS(Z1)INTO HANGERS(Y1).