Home Decorators Collection OXFORD BF-20904 User manual

НОМЕ
DECORATORS
COLLECTION
BF-20904 OXFORD 4 DRAWER FILE CONSOLE
INV#52200
ASSEMBLY INSTRUCTIONS
Made In China
1/11

Thank you for purchasing this quality product. Be sure to check all packing
material carefully for small parts, which may have came loose inside the
carton during shipment. Count all parts and material hardware, then
compare with parts list to be sure all parts are present. If any parts
are missing or damaged, phone, fax, or mail to our Customer Service
Department for efficient and speedy service. Please indicate the
model number and code letter of part(s) needed.
IMPORTANT NOTE: Follow instructions listed below in proper sequence as
numbered to assure fast, easy and correct assembly.
PARTS LIST
RIGHT SIDE PANEL-1PC
LEFT ACROSS PANEL-1PC BACK PANELS-2PCS DRAWER PANEL FRONTS-4PCS
RIGHT LEFT
DRAWER PANEL SIDES-4PCS DRAWER PANEL SIDES-4PCS DRAWER PANEL BACKS-4PCS
2/11

©
KNOBS-4PCS CAM-BOLTS-16PCS
SCREWS-32PCS SCREWS-1PC DOWELS-24PCS
P 6mm x 1/2"
= ፖ
SCREWS-22PCS SCREWS-2PCS FILE HANGERS-8PCS
Т вох 3/8"
CAM-TOOL-1PC SCREWS-24PCS INNER SLIDES-8PCS DRAWER PANEL BOTTOMS-4PCS
8mm x 5/8" WI fall down
prevention
P
REAR PANEL GUIDE-1PC SCREWS-4PCS LOW PANEL-1PC HOOKS-2PCS
fall down fall down fall down
1 prevention VI prevention prevention
7mm x 7/8"
ህሙ С?
0
NOTE: THE SURFACE WITH THE STICKER IS THE BACK SIDE.
3/11

NOTE: e UPON OPENING, THOROUGHLY CLEAN ALL WOODS SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT. IN ORDER
TO PREVENT DAMAGE DURING ASSEMBLY, PLEASE ASSEMBLE THIS ITEM WITH AT
LEAST TWO PEOPLE.
NOTE: TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
HOW TO USE THE CAM- TOOL
NOTE: e THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
4/11

1 ). ASSEMBLE THE DRAWER.
e INSERT 2 DOWELS(O) INTO THE HOLES IN THE PANEL(H) AND ATTACH SIDE PANEL(I/I1) USING
4 SCREWS(N).
e ATTACH А KNOB(K) TO FRONT DRAWER PANEL(H) USING A SCREW(Y).
ө INSERT BOTTOM DRAWER PANEL(V) INTO THE SLOT IN THE SIDE DRAWER PANELS(I/I1).
e INSERT 2 DOWELS(0) INTO THE HOLES IN THE BACK DRAWER PANEL(J) AND ATTACH USING 4
SCREWS (N) .
e INSERT THE FILE HANGER(R) INTO THE CUT-OUT OF THE FRONT 8 BACK DRAWER PANELS(H/J).
5/11

2 ). ASSEMBLE THE INNER SLIDES(U).
ө ATTACH INNER SLIDES(U) TO DRAWER PANEL SIDE(I/I1) USING 6 SCREWS(T).
6/11

3). ASSEMBLE BOTTOM PANEL(B).
e INSERT 2 DOWELS(O) INTO THE HOLES IN THE ACROSS PANEL(F/F1)
ө ROTATE 2 CAM-BOLTS(L) INTO THE HOLES IN THE STAND PANEL(E) AND 2
CAM-BOLTS(L) INTO BOTTOM PANEL(B).
ө PLACE CAM-BOLTS(L) INTO THE HOLES IN THE PANEL(F/F1/E) AND ATTACH USING 4
CAM-LOCKS (M) .
ө ATTACH THE LOW PANEL(Z) TO BOTTOM PANEL(B) USING A SCREW(N1).
7/11

4) ASSEMBLE SIDE PANEL(C/D).
e INSERT 6 DOWELS(O) INTO THE HOLES IN THE PANEL(F/F1/Z).
ө ROTATE 6 CAM-BOLTS(L) INTO THE HOLES IN THE SIDE PANEL(C/D).
ө PLACE CAM-BOLTS(L) INTO THE HOLES IN THE PANEL(B/F/F1) AND ATTACH USING 6
CAM-LOCKS(M) .
e ROTATE THE FOOT(Z2) INTO THE HOLES IN THE BOTTOM РАМЕ! (В).
8/11

5 ( .ASSEMBLE TOP PANEL(A).
Ө ROTATE 6 CAM-BOLTS(L) INTO THE HOLES IN THE TOP PANEL PANEL(A).
ө PLACE CAM-BOLTS(L) INTO THE HOLES IN THE PANEL(C/D/E) AND ATTACH USING 6
CAM-LOCKS (M) .
9/11

6). ASSEMBLE THE DRAWER.
e SLIDE THE DRAWER INNER SLIDES INTO OUTER SLIDES.
7) . ASSEMBLE THE BACK PANEL (G).
e INSERT THE BACK PANEL(G) INTO THE SLOTS IN THE REAR PANEL GUIDE(X).
e ATTACH BACK PANEL(G) AND REAR PANEL GUIDE(X) USING SCREWS(P/Q).
10/11