Home Decorators Collection REFLECTIONS 3 PC MIRRORED CBNT 3 PIECE SET BOX1... User manual

Thank you for purchasing our product!
We appreciate your business!
2-Person
Assembly
2 Hours
Assembly Time
(Approximate)
ASSEMBLY
REQUIREMENTS
Page 1 of 12
Mallet
Tools Required
(Not Provided) Phillips Screwdriver Flat Screwdriver
Please refer and use this assembly instruction to assemble
the product. Contact our customer service department in
case there are any missing or damage parts or hardware.
ASSEMBLY INSTRUCTIONS
Cabinet with Mirror

1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.
2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION
TO CHILDREN AND ANIMALS.
SAFETY PRECAUTION
ASSEMBLY PREPARATION
•Remove all packaging materials, staples and packing straps from the carton.
•Refer to Parts List and Hardware List, and ensure parts and hardware are complete before assembly.
Contact customer service for missing parts.
•Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting
scratched.
TIPS FOR ASSEMBLY
1. Allow ample room for assembly and in close proximity to where the product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the
furniture.
3. Identify all of the parts, hardware and quantities required for each step.
4. During assembly, do not over-tighten any fittings as this may cause damage.
5. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
6. Always place the product on a flat, level surface.
7. Do not sit or stand on the partially assembled product; only use the product for which it is intended.
CARE AND MAINTENANCE
•Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
•Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
•Never allow any kind of liquid to remain on your furniture. Absorption can cause wood to warp or
delaminate.
•Do not place hot items (e.g. hot drinks) directly onto the wood surface.
•Do not drag and/or pull the furniture.
This product is for indoor and household use only - not for commercial use.
Page 2 of 12
ASSEMBLY INSTRUCTIONS
Cabinet with Mirror

LEG
BOTTOM PANEL
1 PC
4 PCS
LEFT PANEL
1 PC
TOP PANEL
RIGHT PANEL
1 PC 1 PC
LEFT DOOR
1 PC
SHELF
RIGHT DOOR
1PC 1 PC
BACK PANEL
1 PC
D8*30
D15 M6*40
M3*12 M3*12 M4*25
M3*15
M3*15
M3.5*30 M4*16
HARDWARE LIST
PARTS LIST
A B C
D E F
G H I
IRON CLASP
FLAT HEAD
SCREW
(2A)
(2B)
(6A)
(6B)
(4A)
(4B)
(5A)
(5B)(7A)(7B)
(8A)
(8B)
(11A)
(11B)
(11C)
(11D)
(11E)
Page 3 of 11
ASSEMBLY INSTRUCTIONS
Cabinet with Mirror

INSERTING CAM-LOCK
CORRECT
TIGHTENING CAM-LOCK
Use a Flat-head Screwdriver to turn Cam-
lock clockwise so it locks onto the head of
the Cam-bolt. Turn until it is snug (about
3/4ths of a turn) -- over-tightening could
damage Cam-lock or/and Cam-bolt.
Align the arrow on the Cam-lock to the
Cam-bolt head and insert the Cam-lock.
Ensure Cam-lock is fully inserted.
CAM-LOCK
X
Shoulder is flushed (on the
same level) with the panel.
Shoulder is above the panel.
CAM-BOLT
INSERTING AND TIGHTENING CAM-BOLT
SHOULDER
Place Cam-bolt on the designated pre-drilled holes on the panel. Use a Phillips Screwdriver
to screw-i n Cam-bolt vertically until shoul der is flushed (on the same level) with panel.
Tools Required
WRONG
Place Cam-bolt on pre-drilled
hole and screw in vertically
x
Insert Cam-lock
with arrow align
to Cam-bolt head
INSTRUCTIONS FOR CAM-BOLT & CAM-LOCK
Page 4 of 11

STEP 1 - INSTALL LEG (B) TO BOTTOM PANEL (A)
a) Insert Wood Dowel (1) into the hole (without screw thread) on (B) and attach leg to bottom-side of (A).
Use a mallet to tap in wood dowel if necessary
b) Use Bolt (4A) fitted with Flat Washer (4B) to fasten leg to bottom panel. Use Allen Key (10) to drive (4A).
STEP 2 - INSTALL LEFT AND RIGHT PANEL (C & D) TO BOTTOM PANEL (A)
a) Position the parts as shown.
b) Attach Left & Right Panel (C & D) to Bottom Panel (A) using Wood Dowel (1) as shown. Use a mallet to
tap in wood dowel if necessary
c) Use Bolt (4A) fitted with Flat Washer (4B) to fasten (C & D) to (A). Use Allen Key (10) to drive (4).
d) With assistance, set the assembly right-side up carefully.
Note: For illustrative purpose, Bottom Panel is shown flat down. It is easier to assemble the Legs with the Bottom Panel
resting vertically on one of its long edge.
Page 5 of 11
4A
4B 4A
4B
4A
4B
4A
4B
4A
4B
4A
4B
4A
4B
4A
4B

STEP 3 - INSTALL TOP PANEL (E)
a) Lay Top Panel (E) bottom-side up on a material that does not scratch or damage the part, and screw in
Cam-bolt (2A). Refer to Page 4 for instructions on inserting and tightening cam-bolt.
b) Insert Wood Dowel (1) into the inner middle holes on top edge of side panels (C & D).
c) Position Top Panel (E) right-side up and attach to (C & D) via cam-bolts and wood dowels.
d) Insert Cam-lock (2B) into designated holes on (C & D) and turn clockwise to lock onto cam-bolt.
(Refer to Page 4 for instructions on inserting and tightening cam-lock.
e) Use Velvet Hole Cover (3) to conceal cam-lock holes.
E
Bottom Side Top Side
Page 6 of 11
2A
2B
2B

STEP 4 - INSTALL DOOR HARDWARE
a) Affix Iron Clasp (6A) to Left and Right Door (F & G) using Flat Screw (6B).
b) Use Flat Head Screw (7B) to fasten Door Wing of Hinge (7A) to (F & G).
c) Use Round Head Bolt (8B) to fasten Knob (8A) to each door.
Door
Wing
Panel
Wing
8A)
(6B)
(6A)
(6B)
(6A)
(8B)
7B)
(7A)
7B)
Page 7 of 11
8A)
(8B)

STEP 5 - INSTALL DOOR AND MAGNETIC LOCK
a) Align drill holes on Panel Wing of Hinge on Left & Right Door (F & G) to pilot holes on the respective
Left & Right Panel (C & D), and use Flat Head Screw (7B) to fasten Panel Wing.
b) Affix Magnet Lock (5A) to the bottom-side of Top Panel (E) using Round Head Screw (5B).
Panel
Wing
((7A)A)
(5A)
(5B)
(7B)
Page 8 of 11

STEP 6 - INSTALL SHELF
a) Select desired the desired level for Shelf (H) and screw in Shelf Holder (12).
b) Place Shelf (H) to sit on Shelf Holder (12).
Page 9 of 11

D
STEP 7 - INSTALL BACK PANEL AND STRAP
a) Place Back Panel (I) to fit on the Side, Top and Bottom Panels - check that Back Panel is
spaced evenly within the 4 panels - and fasten with Round Head Screw (9) as shown.
b) Use a Round Head Screw (9) fitted with Flat Washer (11B) to fasten Strap (11C) to center of
Back Panel.
((11C)
((11B)
Page 10 of 11