Home Decorators Collection OXFORD BF-22766 User manual

HOME
DECORATORS
COLLECTION
BF-22766 OXFORD COLLECTION TALL SECRETARY DESK W/FILE STORAGE
INV#50207
ASSEMBLY INSTRUCTIONS
Made In China
1/16

Thank you for purchasing this quality product. Be sure to check all
packing material carefully for small parts, which may have came loose
inside the carton during shipment. Count all parts and material
hardware, then compare with parts list to be sure all parts are
present. If any parts are missing or damaged, phone, fax, or mail
to our Customer Service Department for efficient and speedy
service. Please indicate the model number and code letter of
part(s) needed.
IMPORTANT NOTE: Follow instructions listed below in proper sequence
as numbered to assure fast, easy and correct assembly.
PARTS. LIST
TOP PANEL-1PC
ACROSS PANEL-IPC
FRONT LOW PANEL-1PC ACROSS PANEL-1PC
2/16

STAND PANEL-1PC STAND PANELS-6PCS SHELF-1PC
P p R
REAR PANEL GUIDE-1PC BACK PANEL-1PC
(LEFT) (RIGHT)
DRAWER PANEL FRONTS-2PCS DRAWER SIDE PANELS-2PCS DRAWER SIDE PANELS-2PCS
5mm X 1/2”
W ә. ge
DRAWER PANEL BOTTOMS-2PCS SCREWS-15PCS
Al 6mm X 1/2”
ui
SCREWS-32PCS
KNOBS—4PCS SHELF SUPPORTS-4PCS
CAM-LOCKS-30PCS CAM-BOLTS-30PCS CAM-TOOL-1PC
3/16

РЕА
FILE HANGERS-4PCS
6mm X 1/2^
«y
SCREWS-40PCS
8mm X 5/8”
”
SCREWS-APCS
INNER
SLIDES-4PC
6mm
X
3/8”
W]
fall
down
prevention
ins
SCREWS—24PCS OUTER SLIDES-4PCS HOOKS-2PCS
X] fall down prevention |Y] fall down prevention |Z| fall down prevention
7mm X 7/8”
ча өзе p
SCREWS-2PCS GECKOS-2PCS SCREWS-2PCS
NOTE: THE SURFACE WITH THE STICKER IS THE BACK SIDE.
4/16

NOTE: e UPON OPENING, THOROUGHLY CLEAN ALL WOODS SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT. IN ORDER
TO PREVENT DAMAGE DURING ASSEMBLY, PLEASE ASSEMBLE THIS ITEM WITH AT
LEAST TWO PEOPLE.
NOTE: TURN THE CAM-BOLT SCREWS UNTIL THEY
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
TO USE THE CAM- TOOL
NOTE: e THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
5/16

1)-ASSEMBLE THE DRAWER.
e INSERT 2 DOWELS(J1) INTO THE HOLES IN THE PANEL(S) AND ATTACH SIDE PANEL(T/U) USING
4 SCREWS(Y).
e ATTACH A KNOB(B1) TO FRONT DRAWER PANEL(S) USING A SCREW(N1).
e INSERT DRAWER PANEL BOTTOM(W) INTO THE SLOT IN THE SIDE DRAWER PANELS(T/U).
e INSERT 2 DOWELS(J1) INTO THE HOLES IN THE DRAWER PANEL BACK(V) AND ATTACH USING 4
SCREWS (Y) .
e INSERT THE FILE HANGERS(H1) INTO THE CUT-OUT OF THE FRONT & BACK DRAWER PANELS(V/S).
6/16

2 ).ASSEMBLE THE INNER SLIDES(P1).
e ATTACH INNER SLIDES(P1) TO DRAWER PANEL SIDE(T/U) USING 6 SCREWS(Q1).
7/16

3 ) -ASSEMBLE THE OUTER SLIDES(R1).
e ATTACH 2 OUTER SLIDES(R1) TO LEFT SIDE PANEL(B) USING 6 SCREWS(Q1).
8/16

4 ) . ASSEMBLE THE OUTER SLIDES(R1).
e ATTACH 2 OUTER SLIDES(R1) TO STAND PANEL(L) USING 6 SCREWS(Q1).
9/16

5) . ASSEMBLE STAND PANEL(M/N).
e INSERT 24 DOWELS(J1) INTO THE HOLES IN THE STAND PANEL(N).
е ROTATE THE 4 CAM-BOLTS(F1) INTO THE HOLES IN THE ACROSS PANEL(H/I).
e PLACE THE CAM-BOLTS(F1) INTO THE HOLES IN THE PANEL(M) AND ATTACH USING 4
CAM- LOCKS (E1) .
6 ) . ASSEMBLE ACROSS/BOTTOM PANEL (G/D).
e ATTACH LOW PANEL(J) TO BOTTOM PANEL(D) USING A SCREW(L1).
e INSERT A DOWEL(J1) INTO THE HOLES IN THE ACROSS PANEL(K).
e ROTATE THE 5 CAM-BOLTS(F1) INTO THE HOLES IN THE PANEL (G/D/L)..
e PLACE THE CAM-BOLTS(F1) INTO THE HOLES IN THE PANEL(L/K) AND ATTACH USING 5
CAM- LOCKS (E1) .
10/16