Home Decorators Collection 516-735 User manual

HOME
DECORATORS
COLLECTION
Exterior Three-Head Lantern
With Post
SKU 516-735 (UPC 046335974463)
(Aged Iron Finish)
INSTRUCTION MANUAL
Page 1
HB7019A-292 E/S

Thank you for purchasing this Home Decorators Collection exterior
light fixture. This product has been manufactured with the highest
standards of safety and quality.
FEATURES:
1.Exterior Three –Head Lantern With Lantern in Aged Iron Finish.
2.Timeless elegant design.
3.Easy to assemble and install.
4.For energy savings this fixture has been engineered to safely use a Self
Ballasted Compact Fluorescent Lamp in place of an incandescent lamp.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer
Service Team at 1-800-986-3460 or visit www.homedepot.com. Please
reference your SKU (516-735 Aged Iron Finish fixture) or UPC
(046335974463).
Page 2

CAUTION:
1.Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
2.CONSTULTA QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS.
3.If you have any non-electrical questions about this fixture, please
contact our Customer Service Team at 1-800-986-3460 or visit
www.homedepot.com. Please reference your SKU (516-735 Aged Iron
Finish fixture) or UPC (046335974463).
4.Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
Page 3
Wire Strippers
Wire Cutters
Safety Glasses Electrical Tape
Phillips Screwdriver Flathead Screwdriver
3 Light Bulbs (100 W Max.
or CFL equivalent)
Wrench

PARTS INCLUDED (parts are not to scale):
Page 4
3 ea Pole
Screw (#17)
3 ea Arm Assembly (#3)
1 ea Pole (#1)
1 ea Pole (#2)
1 ea Base (#16)
1 ea Top Cover (#12)
6 ea Cage
Screw (#24)
3 ea Cage (#25)
3 ea Lock
Nut (#6)
1 ea Wire Housing (#5)
1 ea Cover Finial (#14)
5 ea Wire
Nut (#9)
2 ea Extension Wire
(#7 & #8)
1 ea Wrench
(#26)
1 ea Pole (#39)

PARTS INCLUDED FOR INSTALLATION (parts are not to
scale):
Page 5
3 ea Lock Washers (#37)
3 ea Flat Washers (#36)
1 ea Template (#29)
3 ea Anchors (#31) 3 ea Hex Nuts (#32)

INSTALATION & ASSEMBLY:
1.Carefully unpack the fixture. Lay out all parts on a clean surface.
2.Feed the Wires (#4) of one Arm Assembly (#3) in through one side hole of the
Wire Housing (#5) and through its top opening. Secure each Arm Assembly (#3)
to the Wire Housing (#5) using a Lock Nut (#6), as shown, using the provided
Wrench (#26)(Fig. 1).
3.Unravel the two Extension Wires (#7 & #8). Feed the two Extension Wires (#7
& #8) into the bottom opening of the Wire Housing (#5) through to the top
opening (Fig. 2).
4.Using the provided Wire Nuts (#9), make wire connections between the White
Extension Wire (#7) and the White Arm Assembly Wires (#10) and between the
Black Extension Wire (#8) and the Black Arm Assembly Wires (#11), as shown.
Wrap each wire connection with 2”of electrical tape (Fig. 2).
Page 6
3.Arm
Assembly
4. Wires
5. Wire
Housing 6. Lock
Nut
Fig. 1
26. Wrench

Page 7
INSTALLATION & ASSEMBLY (cont.):
5. Slide the Top Cover (#12) onto the Threaded
Pipe (#13) and onto the Wire Housing (#5).
Thread the Cover Finial (#14) onto the Threaded
Pipe (#13)to secure the Top Cover (#12)(Fig.
2).
6. Unravel and extend the Fixture Ground Wire
(#15)of the Wire Housing (#5) (Fig. 2).
7. Attach Pole (#18)to the Base (#16) using the
provided Pole Screws (#17). Thread Pole (#2)
onto Pole (#18). Thread Pole (#1) onto Pole (#2)
(Fig. 3).
7. White Extension Wire 8. Black Extension Wire
9. Wire Nut
Fig. 2
15. Fixture Ground Wire
12. Top Cover
14. Cover Finial
13. Threaded Pipe
5. Wire Housing
18. Pole
16. Base
17. Pole
Screws
2. Pole
1. Pole
Fig. 3
10. White Arm
Assembly Wires
11. Black Arm
Assembly Wires

INSTALATION & ASSEMBLY (cont.):
8. Feed the Wires (#7, #8 & #15)of the Three-
Head Lantern Assembly (#19) through the
entire Pole/Base Assembly (#20)to the
bottom opening. Screw the Pole/Base
Assembly (#20) into the Wire Housing (#5)
of the Three-Head Lantern Assembly (#19)
(Fig. 4).
Fig. 5
28. Concrete Surface
30. Hole
31. Anchor
27. Wire Conduit
9. Select the desired installation location. Run supply
wires from the breaker panel to the desired
location and prepare the concrete surface. (If you
are unfamiliar with proper electrical practices,
obtain services of a qualified electrician.) When
preparing the concrete surface, be sure that the
Wire Conduit (#27), protecting the supply wires,
extends 1/2”above the Concrete Surface (#28)to
prevent any runoff from entering. Using the
provided Template (#29), mark the locations for
the mounting holes. At the marked locations, drill
½” diameter Holes (#30) approximately 3”deep.
Do not exceed a 3”depth (Fig. 5).
10. Insert the Anchors (#31) into the Holes (#30)
(Fig. 5).
Page 8
Wires
19. Three-
Head Lantern
Assembly
20. Pole/Base
Assembly
5. Wire
Housing
Fig. 4

INSTALATION & ASSEMBLY (cont.):
11.Using the provided Wire Nuts (#9), make the following wire connections (Fig.
6):
White Extension Wire (#7) to White (Neutral)
Supply Wire (#33)
Black Extension Wire (#8) to Black (Hot)
Supply Wire (#34)
Fixture Ground Wire (#15)to Supply Ground Wire (#35)
12.Wrap all wire connections with electrical tape for a more secure connection.
Note: If you have electrical questions, consult your local electrical code for
approved grounding methods.
Page 9
Fig. 6
15. Fixture Ground Wire
8. Black Extension Wire
9. Wire Nut
35. Supply Ground Wire
7. White Extension Wire
34. Black (Hot) Supply Wire
33. White (Neutral) Supply Wire

INSTALATION & ASSEMBLY (cont.):
13.Slide the Base (#16) onto the Anchors (#31)(Fig. 7).
14.Slide a Flat Washer (#36) and a Lock Washer (#37) (in that order) onto each
Anchor (#31). Thread a Hex Nut (#32) onto each Anchor (#31)to secure the
Base to the ground (Fig. 7).
Fig. 7
16. Base
31. Anchor
36. Flat Washer
37. Lock Washer
32. Hex Nut
Page 10

INSTALATION & ASSEMBLY (cont.):
15.Install an incandescent Light Bulb (#22)or a Listed SBCFL (Self-Ballasted
Compact Fluorescent Lamp [not provided]) into the socket of each Hood (#23).
Do not exceed a 100 watt incandescent light bulb, or a26 watt SBCFL (Fig. 8).
16.Secure the Cage (#25)to the Hood (#23) using the provided Cage Screws
(#24), as shown (Fig. 8).
17.Installation is complete. Turn on power at the circuit breaker or fuse box.
Turn the light switch on to activate the fixture.
Page 11
25. Cage
24. Cage
Screw
23. Hood
22. Light Bulb
Fig. 8

Page 12
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1.To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the glass and surface of the fixture.
2.To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened
clean cloth (use clean water, never a solvent) to wipe the inside glass and interior surface of
the fixture.
3.Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of three (3) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement for the product at
the manufacturer’s discretion, provided that the product ahs not been damaged through misuse, abuse,
accident, modifications, alterations, neglect, or mishandling. This warranty shall not apply to any product
that is found to have been improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of
an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to
faculty material or workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied
of fitness for a particular purpose, other than the warranty contained herein. The manufacture
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/expense cost involved in the replacement or repair of
said product.
Symptom Possible Cause Corrective Action
1. Power is off. 1. Make sure power supply is on.
2. Faulty switch. 2. Test or replace switch.
3. Faulty wire connection. 3. Check wiring.
Fuse blows or circuit breaker
trips when light is turned on.
1. Crossed wires or power wire is grounding
out.
1. Check wire connections.
Light will not turn on.

Poste De Luz Con Tres Faroles
SKU 516-735 (UPC 046335974463)
(Acabado de Hierro Envejecido)
HOME
DECORATORS
COLLECTION
MANUALDE INSTRUCCIONES
Page 13
HB7019A-292 E/S

Gracias por la compra de este luminario exterior de Home Decorators
Collection. Este producto ha sido fabricado con los más altos niveles de
seguridad y calidad.
CARACTERÍSTICAS:
1.Poste De Luz Con Tres Faroles exterior en Acabado de Hierro
Envejecido.
2.Diseño elegante.
3.Fácil de montar e instalar.
4.Para fines de ahorro de energía, este luminario ha sido diseñado para
usar de manera segura un Foco fluorescente compacto con balasto
integrado en lugar de un foco incandescente.
PRGUNTAS, PROBLEMAS, PIEZAS FALTANTES:
Antes de regresar a su tienda local de Home Depot, llame a nuestro
Servicio al Cliente al 1-800-986-3460 o visite www.homedepot.com.
Por favor, referir a SKU (516-735 Lámpara con Acabado de Hierro
Envejecido) o UPC (046335974463).
Page 14

PRECAUTIÓN:
1.Antes de comenzar la instalación de esta lámpara o eliminación de una
lámpara instalada, desconecté la alimentación apagando el interruptor o
quitando el fusible en la caja de fusibles.
2.CONSULTE CON UN ELECTRICISTA SI TIENE ALGUNA
PREGUNTA ELÉCTRICA.
3.Si usted tiene cualquier pregunta no eléctrica de esta lámpara, por
favor póngase en contacto con nuestro Servicio al Cliente al 1-800-986-
3460 o visite www.homedepot.com. Por favor, referir a SKU (516-735
Lámpara con Acabado de Hierro Envejecido) o UPC (046335974463).
4.Guarde su recibo y las instrucciones para la prueba de compra.
HERRAMIENTAS NECESSARIAS PARA EL MONTAJE E
INSTALACIÓN (no incluidos):
Page 15
Pelacables Cinta AislanteGafas de Seguridad
Desarmador Phillips CortaAlambres
Desarmador
de Punta Plana
3 Focos (100 Vatios
Maximo o CFL equivalente)
Llave ajustable

PIEZAS INCLUIDAS (partes no están a escala):
Page 16
3 Tornillo para
poste (#17)
3 Ensamblaje del brazo (#3)
1 Poste (#1)
1 Poste (#2)
1 Base (#16)
1 Cubierta superior
(#12)
6 Tornillo para la
jaula (#24)
3 Jaula (#25)
3 Tuerca
hexagonal (#6)
1 Carcasa para
cables (#5)
1 Punta para la
cubierta (#14)
5 Tuerca para
cable (#9)
2 Extension
(#7 y #8)
1 Llave (#26)
1 Poste (#39)

PIEZAS INCLUIDAS PARA LA INSTALACIÓN (partes no
están a escala):
3 Rondanas planas (#36)
3 Rondanas de presión (#37)
3 Tuercas hexagonales (#32)
3 Taquetes (#31)
1 Plantilla (#29)
Page 17

INSTALACIÓN Y ENSAMBLAJE:
1.Desempaque el luminario con cuidado. Coloque todas las partes sobre una
superficie limpia.
2.Pase los cables (#4) de un ensamblaje de brazo (#3) por un agujero lateral de la
carcasa para cables (#5) y a través de su abertura superior. Asegure cada
ensamblaje de brazo (#3) a la carcasa para cables (#5) utilizando una tuerca
hexagonal (#4), como se muestra, utilizando la llave que se incluye (Fig. 1).
3.Desenrolle las dos extensiones (#7 y #8). Pase las dos extensiones (#7 y #8)
por la abertura inferior de la carcasa para cables (#5) a través de la abertura
superior (Fig. 2).
4.Con las tuercas para cables que se incluyen (#9), realice las conexiones de
cables entre la extensión blanca (#7) y los cables del ensamblaje del brazo blanco
(#10) y entre la extensión negra (#8) y los cables del ensamblaje del brazo negro
(#11), como se muestra. Envuelva cada conexión de cables con 2”de cinta de
aislar (Fig. 2).
Page 18
3. Ensamblaje
del brazo
5. Carcasa
para cables 6. Tuerca
hexagonal
26. Llave
Fig. 1
4. Cables

Page 19
INSTALACIÓN Y ENSAMBLAJE (cont.):
7. Extensión blanca 8. Extensión negra
9. Tuerca para cables
15. Cable a tierra
del luminario
12. Cubierta superior
14. Punta para
la cubierta
13. Tubo roscado
5. Carcasa para
cables
5. Deslice la cubierta superior (#12)en el tubo
roscado (#13) y la carcasa para cables (#5).
Enrosque la punta de la cubierta (#14)en el tubo
roscado (#13) para asegurar la cubierta superior
(#12)(Fig. 2).
6. Desenrolle y extienda el cable a tierra del luminario
(#15)de la carcasa de cables (#5) (Fig. 2).
7. Fije el poste (#18) a la base (#16) utilizando los
tornillos para poste (#17)que se incluyen.
Enrosque el poste (#2) en el otro poste
(#18).Enrosque el poste (#1) en el otro poste (#2)
(Fig. 3).
Fig. 2
16. Base
Fig. 3
18. Poste
17. Tornillos
para poste
1. Poste
2. Poste
10. Cables del ensamblaje
del brazo blanco
11. cables del ensamblaje
del brazo negro

Page 20
INSTALACIÓN Y ENSAMBLAJE (cont.):
8. Pase los cables (#7, #8 y #15) del
ensamblaje del farol con tres cabezas (#19)
por todo el ensamblaje del poste/base (#20)
hasta la abertura inferior. Enrosque el
ensamblaje del poste/base (#20)en la
carcasa para cables (#5) del ensamblaje del
farol con tres cabezas (#19)(Fig. 4).
9. Seleccione el lugar de la instalación. Pase los
cables del panel del disyuntor de circuitos al lugar
seleccionado y prepare la superficie de concreto.
(Si no está familiarizado con las prácticas
eléctricas, contrate los servicios de un electricista
calificado). Cuando prepare la superficie de
concreto, asegúrese de que el conducto de cables
(#27), el cual protege los cables de alimentación,
se extienda 1/2”por arriba de la superficie de
concreto (#28) para evitar la entrada de algún
derrame. Con el uso de plantilla que se incluye
(#29), marque los lugares para los agujeros de
montaje. En los lugares marcados, taladre
agujeros con un diámetro de ½” (#30) con una
profundidad de 3”aproximadamente. No exceda
de una profundidad de 3”(Fig. 5).
10. Inserte los taquetes (#31)en los agujeros (#30)
(Fig. 5).
Fig. 5
27. Conducto
de cables
28. Superficie de concreto
30. Agujero
31. Taquete
Fig. 4
Cables
19. Ensamblaje
del farol con tres
cabezas
20. Ensamblaje
de poste/base
5. Carcasa
para cables