Home Styles Floral Blossom 88 5558 83 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5558 83
Floral Blossom
Chaise with Cushion
Head Cap Bolt (long)
2 pcs.(+1 extra)
Head Cap Bolt (large)
2 pcs.(+1 extra) Head Cap Bolt (short)
2 pcs.(+1 extra)
Key Wrench
1 pc.
Bolt
6 pcs.(+1 extra)
Flat Washer
6 pcs.(+1 extra)
Flat Washer (small)
2 pcs.(+1 extra) Flat Washer (large)
2 pcs.(+1 extra)
Spring Washer
8 pcs.(+1 extra)
Nut
6 pcs.(+1 extra)
Nut Cap
6 pcs.(+1 extra) Wheel Cap
2 pcs.(+1 extra)
A.
Seat
1 pc.
B.
Arm
1 pc.
C.
Arm
1 pc.
D.
Back Frame
1 pc.
E.
Support
1 pc.
F.
Axle
1 pc.
G.
Wheel
2 pcs.
H.
Cushion
1 pc.
Tools required for assembly : Slotted screwdriver
Part List
Hardware List
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Small
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Large
Hex Wrench
1 pc.

Figure 1
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Key Wrenches and Hex Wrench in a safe place as you may need to tighten up the Nuts and Head Cap Bolts
in the future.
Figure 2
Insert all Bolts into the
pre-drilled holes of
Arm (B) and (C).
(See Figure 1)
STEP 1
Attach Arm (B) to Seat (A) with Flat Washers,
Spring Washers, Nuts and Nut Caps.
(See Figure 2)
STEP 2
Nut Cap
Nut
Flat Washer
Spring
Washer
B
C
B
A
Assembly Instructions 2/4

Assembly Instructions 3/4
STEP 3
STEP 4
C
D
Place Back Frame (D) into position.
(See Figure 3)
Attach Arm (C) to Seat (A) with
Flat Washers, Spring Washers,
Nuts and Nut Caps.
Attach Support (E) to unit with
Flat Washers (small), Spring Washers
and Head Cap Bolts (long).
Slide Axle (F) into unit,
aligning it in a centered position (left to right).
Lock Axle (F) in place by inserting
Head Cap Bolts (short) into the
per-drilled holes of unit
Attach Wheels to unit with
Flat Washers (large) and
Head Cap Bolts (large).
(See Figure 4)
Nut Cap
Nut
Flat Washer
Spring Washer
Figure 3
Figure 4
F
EG
GHead Cap Bolt (short)
Plastic Ring is on inside of wheel
Large Hex Wrench
Head Cap Bolt (long)
Spring Washer
Flat Washer (small)
Head Cap Bolt (large)
Flat Washer (large)
Head Cap Bolt (large)
Flat Washer (large)

Assembly Instructions 4/4
Turn the chaise to its’ upright position.
Cover the wheel holes with Wheel Caps. (See figure 5)
Place Cushion (H) onto seat.
Use the tie-downs on Cushion (H) to attach to chaise.
STEP 5
Figure 5
Wheel Cap
H