Home Styles 88 5180 15 User manual

PART LIST
HARDWARE LIST
A.
Top
1 pc.
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
D.
Front Frame
1 pc.
E.
Front Frame
1 pc.
J.
Stretcher
1 pc.
L.
Keyboard
1 pc.
K.
Keyboard
1 pc.
88 5180 15
Executive Desk
M.
Drawer
2 pcs.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Cam Lock
8 pcs.(+4 extra)
Cam Lock Screw
8 pcs.(+1 extra)
Pull Handle
4 pcs.
M4x38
Machine Screw
4 pcs.
M3x25
Wood Screw
for Drawer Side
16 pcs.(+1 extra)
M3x32
Wood Screw
6 pcs.(+1 extra)
M3x16
Wood Screw
for Drawer Bottom
8 pcs.(+1 extra)
M3x10
Wood Screw
for Hinge
6 pcs.(+1 extra)
M6x32
Head Cap Bolt
21 pcs.(+1 extra)
Tools required for assembly : Phillips screwdriver, Level
(Please refer to the last page(s) of these
instructions for drawer assembly steps.)
F.
Front Rail
1 pc.
G.
Back Panel
1 pc.
I.
Divider
1 pc.
H.
Divider
1 pc.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Spring Washer
21 pcs.(+1 extra)
Flat Washer
21 pcs.(+1 extra)

STEP 1
STEP 2
STEP 3
Attach Dividers (H), (I) to unit with Cam Locks.
(See Figure 1)
Attach Back Panel (G) to unit with Cam Locks.
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Key Wrench in a safe place as you may need to tighten up the Bolts in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Attach Front Frames
(D), (E) to Front Rail (F)
with Wood Screws.
Assembly Instructions 2/5
G
D
D
E
E
Insert Cam Lock Screws
into the pre-drilled holes
of Back Panel (G) and
Front Frames (D), (E).
Cam Lock Screw
Wood Screw
F
G
I
H
Figure 1

Assembly Instructions 3/5
STEP 4
STEP 5
Place Top (A) upside down on soft cloth.
Attach Top (A) to unit with Head Cap Bolts, Spring Washers and Flat Washers.
J
B
C
A
Figure 2
Figure 3
Flat Washer
Spring Washer
Head Cap Bolt
Wood Screw
Attach Side Frame (C) to unit with Head Cap Bolts,
Spring Washers and Flat Washers. (See Figure 2)
Attach Stretcher (J) to unit with Wood Screw. (See Figure 3)
Attach Side Frame (B) to unit with Head Cap Bolts,
Spring Washers, Flat Washers and Wood Screw.

Assembly Instructions 4/5
STEP 7
STEP 6
Turn unit to its’ upright position.
Slide Keyboard and Drawers (M) into place.
To level the unit, adjust the adjustable levelers on the bottom of legs.
(See Figure 6)
Note: Unit must be level to work properly.
Attach Keyboard (L) to Keyboard (K)
with Wood Screws (for Hinge).
Attach Pull Handles to Keyboard
with Machine Screws. (See Figure 4)
M
M
Wood Screw (for Hinge)
LK
Figure 4
Figure 6

Assembly Instructions 5/5
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
M2
M2
M2
M3
M3
M3
M4
M4
M4
M5
M5
M1
M1
M1
Drawer (M)
Part List
M1.
Drawer Front
2 pcs.
M5.
Drawer Bottom
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
Figure 3
Figure 4
Insert wood screws (4X)short
into the pre-drilled holes in M5,
tighten screws. (See Figure 3)
Attach Pull Handle with
machine screw.
(See Figure 4)
Slide M5 into the grooves in M3
and M4. Be sure to push M5 all
the way forward so it meets M1.
(See Figure 2)
STEP 1
STEP 2
STEP 3
STEP 4
Tighten all screws used in
drawer assembly.
Attach M1 to M3 and M4, using
wood screws (4X),long
tighten halfway.
Attach M2 to M3 and M4 using
wood screws (4X),long
tighten halfway. (See Figure 1)