Home Styles Barnside Pantry 88 5516 653 User manual

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Hardware List
88 5516 653
Barnside Pantry
Tools required for assembly : Phillips screwdriver
For assembly see instructions in carton 88 5516 654
Cam Lock
30 Pcs. (+6 extra)
Hex Wrench
1 Pc.
Small Hex Wrench
1 Pc.
Adjustable Pin
16 Pcs. (+1 extra)
Magnet
4 Pcs.
Wood Screw (long)
8 Pcs. (+1 extra)
M3x20 Wood Screw (short)
30 Pcs. (+1 extra)
Wood Screw
for Magnet
8 Pcs. (+1 extra)
M3x15
M3x10
Door Handle
4 Pcs.
Drawer Handle
2 Pcs.
Machine Screw
8 Pcs.
M4x25
Cam Lock Screw
30 Pcs. (+2 extra)
B.
Side Panel
1 Pc.
J.
Side Panel
1 Pc.
C.
Side Panel
1 Pc.
K.
Side Panel
1 Pc.
N.
Door
1 Pc.
P.
Door
1 Pc.
M.
Door
1 Pc.
O.
Door
1 Pc.

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Also need the part(s) and hardware from carton 88 5516 653
88 5516 654
Barnside Pantry
D.
Base
1 Pc.
E.
Back Stretcher
2 Pcs.
F.
Back Stretcher
3 Pcs.
G.
Back Panel
2 Pcs.
L.
Back Panel
2 Pcs.
Q.
Shelf
4 Pcs.
I.
Middle Panel
1 Pc.
A.
Top
1 Pc.
H.
Front Rail
1 Pc.
R.
Drawer
1 Pc.
(Please refer to the last page of
instructions for steps to complete drawer assembly)

Assembly Instructions 3
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
*After assembly item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Top (A),
Side Panels (B), (C), (J), (K) and Middle Panel (I).
(See Figure 1)
Attach Magnets to Top (A) with
Wood Screws for Magnet at the
pre-drilled holes in Top (A).
(See Figure 2)
STEP 2
Attach Magnets to Front Rail (H) with Wood
Screws for Magnet.
Attach Base (D), Back Stretcher (F)
and Front Rail (H) to Side Panel (B)
with Cam Locks.
Attach Back Stretcher (E) to unit then slide
Back Panels (G) into place.
B
J
K
D
B
GG
FE
H
C
A
I
Figure 1
Figure 2
Cam Lock Screw
Wood Screw for Magnet
Magnet
Cam Lock
2/5

Assembly Instructions 4
STEP 3
Attach Side Panel (C) to unit with Cam Locks.
STEP 4
Attach Middle Panel (I) to unit with Cam Locks.
STEP 5
Attach Back Stretchers (F)
to Side Panel (J) with Cam Locks.
Attach Stretcher (E) to Side Panel (J)
then slide Side Panels (L) into position.
Attach Side Panel (K) to unit with Cam Locks.
K
LL
F
F
E
J
I
C
Cam Lock
3/5

Assembly Instructions 5
STEP 6
Attach Top (A) to unit with Cam Lock.
O
M
N
P
Q
Q
Q
R
Q
A
Wood Screw
(short)
4/5
STEP 7
Attach unit from Step 6 to unit from Step 4 with
Cam Locks.
Attach Door Handles to Doors (M), (N), (O) and (P)
with Machine Screws. (See Figure 3)
Attach Doors (M), (N), (O) and (P) to unit by
sliding the door lift hinges into the side panel lift
hinges. (See Figure 4)
Insert Adjustable Pins into the middle panels at the
desired level.
Slide Shelves (Q) and Drawer (R) into position.
Figure 3
Figure 4
Figure 5
Adjustable Pin
STEP 8
To level the unit, adjust the adjustable levelers on
the bottom of the legs. (See Figure 5)
Insert 24X Wood Screws (short) from the back of the
unit and tighten.
Note: Please make sure unit is level before
tightening these screws.

Assembly Instructions 6
Part List
Drawer R
R1.
Front Part
1 Pc.
R2.
Back Part
1 Pc.
R3.
Side Part
1 Pc.
R4.
Side Part
1 Pc.
R5.
Base Part
1 Pc.
R1
R1
R2
R5
R5
R3
R3
R4
R4
R2
STEP 1
Attach R1, R2 and R3 using a Phillips
screwdriver and long wood screws
(4X), tighten halfway.
Attach R1, R2 and R4 using long
wood screws (4X), tighten halfway.
(See Figure 1)
STEP 2
Slide R5 into grooves in R3 and R4. Be sure
to push R5 all the way forward so it meet R1.
(See Figure 2)
Figure 1
Figure 2
Figure 4
Figure 3
MAKE SURE ROLLER
IS ON THE BACK
Tighten all screws used in drawer assembly.
5/5
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in R5,
tighten screws. (See Figure 3)
STEP 4
Attach Drawer Handles with
Machine Screws.
(See Figure 4)