Home Styles KF9119 User manual

Hutch Unit Part List
88 5180 307
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed. Casual Attire For Today's Home
Hardware List
Hex Wrench
1 pc.
Head Cap Bolt
8 pcs. (+1 extra)
Cam Lock
16 pcs.(+1 extra)
Cam Lock Screw
16 pcs.(+1 extra)
Machine Screw
4 pcs.
A.
Top
1 pc.
Wood Screw
12 pcs. (+1 extra)
Adjustable Pin
24 pcs. (+2 extra)
H.
Back Piece
2 pcs.
Tools required for assembly : Phillips screwdriver
Wood Screw
for Magnet
8 pcs. (+1 extra)
Magnet
4 pcs.
I.
Back Panel
3 pcs.
P.
Leg
1 pc.
B.
Side Panel
1pc.
D.
Middle Panel
1 pc.
F.
Front Rail
1 pc.
G.
Back Stretcher
2 pcs.
J2.
Shelf
4 pcs.
K1.
Fixed Shelf
1 pc.
M.
Door
1 pc.
N.
Door
1 pc.
C.
Side Panel
1pc.
E.
Middle Panel
1 pc.
J1.
Fixed Shelf
2 pcs.
K2.
Shelf
2 pcs.
L.
Glass Door
4 pcs.
Steel Plate
Connector
2 pcs.
Wood Screw
for Steel Plate
Connector
8 pcs. (+1 extra)
Dining Hutch
Door
Pull Handle
2 pcs.
Small
Hex Wrench
1 pc.
Arts & Crafts

IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to tighten up the Head Cap Bolts in the future.
STEP 1
Assembly Instructions 2/3
Put Cam Lock Screws
into the pre-drilled holes of
Side Panel (B),(C),
Middle Panel (D),(E) and tighten.
Attach Back Stretcher (G) to Side Panel (B)
with Cam Lock.
Attach Back Piece (H) to
Back Stretcher (G) and slide
Back Panel (I) into place.
Attach second Back Stretcher (G)
to the unit with Cam Locks.
STEP 2
B
Cam Lock
BC
DE
Cam Lock Screw
Cam Lock
G
G
H
HI
I
I
Assemble Fixed Shelf (J1),(K1)
Middle Panel (D) and (E)
using Cam Locks.
Attach assembled part to the unit with
Head Cap Bolts and Cam Locks.
D
E
J1
J1
K1
STEP 3
Head Cap Bolt
Cam Lock
M
N
Remove Wood Screw from
Door (M) and (N).
Slide Glass (L) into the door frame
as shown Tighten Wood Screws .
L
LL
L
Wood Screw

Assembly Instructions 3/3
STEP 4
to the unit.
Attach Side Panel (C) to
the unit with Cam Locks.
Attach Front Rail (F)
STEP 5
C
Cam Lock
F
Turn the unit to its upright
position.
Insert Adjustable Pins into
side panels and middle panels
at the desired level.
Slide Shelf (J2) and (K2) into place.
Assemble Pull Handles to Door (M)
and (N) with Machine Screws.
(see Figure 1)
Attach Door (M) and (N) to the side panels by sliding the door lift hinges into the side panel
lift hinges. (see Figure 2)
Place Top (A) onto the unit with Head Cap Bolts.
K2 J2
A
N
M
(Figure 2)
(Figure 1)
Insert Wood Screws from the back
and tighten.
Place the Hutch unit onto the Buffet unit.
Attach Steel Plate Connectors by inserting
Wood Screws and tighten. (see Figure 3)
STEP 6
(Figure 3)
Wood Screw
Steel Pate Connector
Wood Screw
K2 J2
J2
J2
Head Cap Bolt
Adjustable Pin

HARDWARE LIST
Attention !
For safety reasons, please follow these additional instructions to
prevent the unit from tipping over.
Bracket
at the wall
Bracket
at the top
of the unit
Wood
Screw
Wall Screw
Plastic Belt
Top of unit
(figure X)
Wood Screw (short)
2 pcs.(+1 extra)
Wall Screw (long)
2 pcs.(+1 extra)
Anchor
2 pcs.(+1 extra)
Bracket
4 pcs.(+1 extra)
Plastic Belt
2 pcs.(+1 extra)
Assembly Instructions
Place the unit at desired
location in room.
Drill two ¼” holes in wall at the appropriate
location.
Insert the Anchors into the wall holes and
attach the Brackets using Wall Screws.
Attach the Brackets at the pre-drilled holes
on the top of the unit using Wood Screws.
Use the Plastic Belt to secure the
Brackets on the unit to the Brackets on
the wall (See figure X).
Put the tie end of the belt into the loop end
of the belt and pull until tight.
Drill two ¼” holes in wall