Home Styles 20 05507 0070 User manual

Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
20 05507 0070
Vanity with Mirror
IMPORTANT
Refer to later page(s) of these
instructions for drawer assembly.
K.
Mirror
1 pc.
M.
Drawer
1 pc.
L.
Drawer
2 pcs.
H.
Batten
2 pcs.
A.
Top
1 pc.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
D.
Front Rail
2 pcs.
E.
Front Rail
1 pc.
F.
Side Panel
1 pc.
G.
Side Panel
1 pc.
I.
Back Panel
1 pc.
J.
Stretcher
1 pc.
Hardware List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Part List
Handle
4 pcs.
Cam Lock Screw
12 pcs. (+1 extra)
Cam Lock
12 pcs. (+1 extra)
M4x30
Wood Screw
26 pcs. (+1 extra)
M3.5x20
Wood Screw (short)
16 pcs. (+1 extra)
M4x30
Machine Screw
8 pcs.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
M6x40
Head Cap Bolt (long)
8 pcs. (+1 extra)
Spring Washer
13 pcs. (+1 extra)
Flat Washer
13 pcs. (+1 extra)
Cover
2 pcs. (+1 extra)
M6x30
Head Cap Bolt
13 pcs. (+1 extra)

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Place Top (A), Side Frames (B), (C), Side Panels (F) and (G) on a soft cloth.
Insert Cam Lock Screws into pre-drilled holes in Top (A) Side Frames (B, (C),
Side Panels (F) and (G), then tighten.
(See Figure 1)
Figure 1
C
A
B
Cam Lock Screw
G
F

Assembly Instructions 3/8
G
F
A
E
I
Flat Washer
Cam Lock
Spring Washer
STEP 2
Place Top (A) upside down on
a soft cloth.
Attach Side Frame (F) to Top (A)
with Cam Locks.
(See Figure 2)
Attach Front Rain (E) to unit
with Cam Locks.
Attach Side Frame (G) to unit
with Cam Locks.
STEP 3
Attach Back Panel (I) to unit
with Flat Washer, Spring Washer
and Head Cap Bolts,
tightening bolt only halfway.
(See Figure 3)
Head Cap Bolt
Figure 2 Figure 3

Assembly Instructions 4/8
STEP 4
Attach Front Rail (D) to unit
with Cam Lock.
Attach Side Frame (C) to unit
with Flat Washers,
Spring Washers,
Head Cap Bolts,
and Cam Lock
tightening bolts only halfway.
C
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
Cam Lock
Cover
STEP 5
Attach Front Rail (D) to unit
with Cam Lock.
Attach Stretcher (J) to unit
with Cam Lock.
(See Figure 4)
Attach Side Frame (B) to unit
with Flat Washers,
Spring Washers,
Head Cap Bolts, and
Cam Locks,
tightening bolts
only halfway.
Cover Cam Locks
with Covers.
(See Figure 5)
Tighten all bolts used
in Step 3, 4 and 5.
Head Cap Bolt
Spring Washer
D
D
J
B
Figure 5
Cam Lock
Cam Lock
Figure 4

Part List
Assembly Instructions 5/8
L1.
Drawer Front
2 pcs.
L2.
Drawer Back
2 pcs.
L3.
Drawer Side
2 pcs.
L4.
Drawer Side
2 pcs.
L6.
Jewelry Box
2 pcs.
Drawer (L)
STEP 9
Place Jewelry Box (L6) into position.
STEP 7
Slide Drawer Bottom (L5) into groove.
Attach Drawer Bottom (L5) to unit with Wood Screws (short).
STEP 6
Attach Drawer Front (L1) and Drawer Back (L2)
to Drawer Side (L3) with Wood Screws.
Attach Drawer Side (L4) to unit with Wood Screws.
L4
L2
L3
L6
Roller at back
Handle
Machine Screw
Wood Screw (short)
L5.
Drawer Bottom
2 pcs.
L1
Wood Screw
STEP 8
Attach Handle with Machine Screws.
L5
Bottom

Part List
Assembly Instructions 6/8
M1.
Drawer Front
1 pc.
M2.
Drawer Back
1 pc.
M3.
Drawer Side
1 pc.
M4.
Drawer Side
1 pc.
M6.
Support
1 pc.
M5.
Drawer Bottom
1 pc.
Drawer (M)
STEP 12
Attach Handles with Machine Screws.
STEP 11
Slide Drawer Bottom (M5) into groove.
Attach Supports (M6) to unit
with Wood Screws.
Attach Drawer Bottom (M5) to unit
with Wood Screws (short).
STEP 10
Attach Drawer Front (M1) and
Drawer Back (M2) to Drawer Side (M3)
with Wood Screws.
Attach Drawer Side (M4) to unit
with Wood Screws.
Handle
Machine Screw
M4M2
M3
M5
Roller at back
Bottom
Wood Screw (short)
M6
Wood Screw
M1
Wood Screw

Assembly Instructions 7/8
Figure 6
STEP 14
Attach Battens (H) to Mirror (K) and unit
with Head Cap Bolts (long), then tighten.
Level unit by adjusting the
adjustable levelers on bottom of unit.
(See Figure 6)
Note: Unit must be level to work properly.
H
ML
K
L
H
STEP 13
Turn unit over to its upright position.
Slide Drawers (L) and (M)
into position.
Head Cap Bolt (long)

Assembly Instructions 8/8
Hardware List
STEP 15
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 7
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319