Home Zone Security ES00935G User manual

10x15cm
Client: Amazon
IM
T101P61Z01
Client ID: Item NO.:
Division: File NO.:
Finish Date:
Contact: Art window/Reading ext:8237
Email: [email protected]
Packaging Description:
Package Size:
PDS 540 File Information
Joe
Amy
Hunt
Carol
Packaging Design
Implement Confirmation
Sales Division
Applicant Designer
Design Division
Signed by Applicant & Sales Division
forall Items
20211218
Colors:
20211218
ES00935G10163406
CMYK
Cutter
Diecut
LINKABLE SOLAR POWER
TWIN HEAD LED
SECURITY LIGHT
(2-PACK)
the bright way to do home security.
ES00935G
INSTALLATION INSTRUCTIONS
®

PLEASE READ CAREFULLY AND SAVE THESE INSTRUCTIONS, AS YOU
MAY NEED THEM AT A LATER DATE.
Warning
IMPORTANT SAFETY OPERATING INSTRUCTIONS
PRECAUTION
LOCATION
1. Please read all warning and instruction labels which are included in the
box and fixture to avoid personal injury, property damage caused by fire,
cuts, bruises, death and other dangers.
2. Please follow these general precautions before installing, maintaining, or
fixing.
1. This fixture should be installed outdoors to a wall.
2. The light fixture should be mounted approximately 5.9~11.5 ft. (1.8m~3.5m)
above the ground.
3. Do not immerse components in liquid.
4. This device may not cause harmful interference, and this device must
accept any interference received, including interference that may cause
undesired operation.
Fixture can be wall mounted.
Recommended installation height: 8 - 11.5 feet above the ground.
Environment will affects the sensor range. It is recommended not to mount
the fixture near a heat source like an air conditioner, vent, or furnace
exhaust, or in a direction facing a light reflecting object.
Maybe the sensor detection distance will decrease lower than 40 feet in
some special environment.
1. The packing contains small parts that could be swallowed by children.
2. Keep the packaging material away from children and pets.
3. Do NOT look directly at the LED lights.
4. This light fixture is NOT A TOY and is NOT suitable children.
5. We do not take responsibility if the instruction manual is not followed
correctly or if the product is handled improperly resulting in damage to
person or property.
6. In order to prevent potential serious INJURY or DEATH, babies and
children are NOT allowed to touch batteries. If a battery is accidentally
swallowed, please contact with your doctor immediately.
7. The operating temperature of solar panel is between -4°F (-20°C) and
122°F (50°C).
8. Rechargeable battery only. Recycle or dispose of batteries properly.
9. Do not open,short circut,or mutilate batteries. Injury may be occurred.
WARNING
WARNING:This product can expose you to chemicals including lead
and lead compounds, Di(2-ethylhexyl)phthalate (DEHP), which are
known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
1

A B C
D E
Light fixture
What's in the box
x 7 x 7
Parameter
1Illumination output: approx. 1500 lumens / 5000K
Sensor detect range: 40 feet x 180 degree
Power source: 3 x 1.2V 2200mAh Lithium rechargeable battery.
2
3
PREPARATION
1. Please read all warning and instruction labels which are included in the
box and fixture to avoid personal injury, property damage caused by fire,
cuts, bruises, death and other dangers.
2. Please follow these general precautions before installing, maintaining, or
fixing.
Tools required for assembly (not included): phillips screwdriver, safety
goggles, power drill and ladder.
1. The packing contains small parts that could be swallowed by children.
2. Keep the packaging material away from children and pets.
3. Do NOT look directly at the LED lights.
4. This light fixture is NOT A TOY and is NOT suitable children.
5. We do not take responsibility if the instruction manual is not followed
correctly or if the product is handled improperly resulting in damage to
person or property.
6. In order to prevent potential serious INJURY or DEATH, babies and
children are NOT allowed to touch batteries. If a battery is accidentally
swallowed, please contact with your doctor immediately.
7. The operating temperature of solar panel is between -4°F (-20°C) and
122°F (50°C).
8. Rechargeable battery only. Recycle or dispose of batteries properly.
9. Do not open,short circut,or mutilate batteries. Injury may be occurred.
Anchor
Solar panel
Mounting plate
Mounting screw
2

2Use a power drill (not included) to drill the holes on your chosen
mounting surface first. Then use 3 of the Plastic Anchors (Part E)
and Screws (Part D) to fasten the mounting plate on the wall.
Note: The light fixture should be mounted approximately 8 - 11.5
feet (2.4m-3.5m) above the ground.
Mounting the light fixture as shown in the below figures
Use your finger
to push up on the
mount plate.
Slide the mounting
plate down off the
back of the light
fixture.
Installation
1
D
D
D
E
E
E
3

Slide the light fixture into the grooves of the mounted plate in
parallel.
3
4Mounting the solar panel as shown in the below figure:
• Use a power drill (not included) to drill 4 holes on your
chosen mounting wall.
• Use 4 of the Plastic Anchors (Part E) and Screws (Part D) to
fix the solar panel on the wall.
• Adjust the angle of solar panel (Part C) to the direction which can
receive maximum direct sunlight during daytime.
Note: The distance between light fixture and the solar panel must
NOT exceed 15ft.
Note: The solar panel must receive direct sunlight at least 3 hours.
D
E
C
A
D
E
4

How it Works
1. Swing the lamp heads to adjust the lamp head left and right
or up and down to get the desired lamp direction.
2. Gently grasp the motion sensor and adjust the sensor left and
right or up and down to get the desired sensor direction.
5Connecting the light fixture to the solar panel as shown in the
below figure
Carefully connect the wire from the solar panel (Part C) into the
socket located under the Light Fixture (Part A), make sure the
plug is securely connected. Your solar panel will now begin to
charge.
Adjusting the lamp heads and motion sensor
A
C
5

3. TIME Setting
This setting is used to control the time span of how long the light
remains on when motion is deteced.Set the switch to the 30, 60,
120 seconds position. The security light will stay on as long as
motion is detected and will go off after the time span you set after
no motion is detected.
2. 4 Working Modes
• Test mode: Check the light’s sensory function in order to testthe
sensory range. The time duration for the light will be 5s.
• Auto: The light will turn on to low brightness automatically atnight.
When motion is detected, the light will turn on full brightness for the
selected time duration.
• On: The light will stay on full brightness when it is switched onand
turn off when it is switched off by light switch, whether it is day or at
night.
Product Function Description
1. SENS Setting
Adjust the SENS setting to adjust range of Passive Infrared
Motion Sensor
SENS
MODE
TEST
30S 60S 120S
AUTO ONOFF
Slide toward the “ ” (low) position for short detection range (3-30 ft).
Slide toward the “ ” (Middle) position for middle detection range ( 3-49 ft).
Slide toward the “ ” (high) position for long detection range ( 3-70 ft).
6

4. Linkable Channels Setting
This setting has 4 channels. As long as you choose “linkable”
security light or sensors from Home Zone Security, selecting a
specific channel to connect all linkable security lights and sensors.
They will be grouped as an invisible system and working together.
One linkable light triggered, all linkable lights on.
CHANNELS
Use 3pcs 1.2V AA size 2200mAh Ni-MH rechargeable battery. For
best performance, replaced with the new Ni-MH rechargeable
batteries every 18 months. When the battery expires, it must be
recycled or disposed of properly. Please contact your local waste
disposal authority for correct procedure. Do not put batteries into fire.
•
Only rechargeable batteries are to be used.
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
•
Exhausted batteries must be removed from the product.
•
Batteries must be placed at the correct polarity.
RECHARGEABLE BATTERY
1. Remove the 4 screws from the bottom of the base and the battery
cover.
2. Take all batteries out of the battery chamber.
3. Replace with 3 new 1.2V AA size 2200mAh Ni-MH rechargeable
batteries.
4. Double check if the polarity is correct.
5. Put the battery cover back and mount 4 screws in position.
BATTERY REPLACEMENT:
CH1 CH2 CH3 CH4
7

FCC
Cleaning and Maintenance
To prolong the original appearance, clean the light fixture with a
soft, damp cloth. Do not use paints, solvents, or other chemicals on
this light fixture. They could cause a premature deterioration of the
finish.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
This device complies with FCC Part 15 of FCC Rules.
Warning
: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE
: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
8
This equipment should be installed and operated with a minumum distance of 20 cm
between the radiator and your body.

Get exclusive offers and deals
when you subscribe!
Thank you for choosing Home Zone Security!
We are here to support you every step of the way.
Please be sure to contact our customer support for troubleshooting
and register your product for additional benefits. Products must be
sold by an authorized reseller or distributor to be valid.
• Receive your extended warranty
• Get professional warranty support
•Be the first to hear the latest product news.
• Get exclusive deals delivered to you email.
Scan below for link:
homezonesecurity.com
[e-mail]
US: [phone]
Register & Subscribe today to protect your investment and join our email list!
Why Register?
Distributed by
4198 Industry Way
Flowery Branch, GA 30542 USA
Made In Cambodia
Horizon Marketing Group, LLC
®