Home Zone Security ES06508V User manual

Curved Head Security Light
Model No. ES06508V
[phone]
IMPORTANT SAFETY OPERATING INSTRUCTIONS
1. Please read all warning and instruction before attempting to install this light.
2. Disconnect power before installing or servicing.
Risk of electrical shock
1. Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
2. Make sure all electrical and grounded connections are in accordance with the National Electrical Code
and applicable local code requirements.
3. All wiring connections should be compliant with UL standard.
Risk of injury
1. Wear gloves and safety glasses at all times when moving luminaire from carton, installing, servicing or
performing maintenance.
2. Avoid direct eye exposure to the light source while it is on as this may cause irreparable damage to the
eyes.
3. Account for small parts and destroy packing material, as these may be hazardous to children.
Risk of burn
1. Allow fixture to cool before touch.
2. Do not exceed maximum wattage marked on luminaire label.
Attention: lights must be installed by an experienced household wire installer or a qualified electrician,
Electrical system and the electrical connection method of light fixture must conform to the national electrical
standards and specification requirements of the local architecture.
FCC
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
securit y
www.homezonesecurity.com

Curved Head Security Light
[phone]
1. Illumination output: approx. 1600 lumens / 5000K
2. Wattage: 18W
3. Power source: AC120V/60Hz
4. Detect range: up to 40feet (12m), 180 degree
REF. PARTS
HOW TO INSTALL
PARAMETER:
A B C D E F
Model No. ES06508V
1. Install the mounting bar to the outlet box with the stamped word "FRONT" facing away from the outlet box, use two mounting screws
that best fit the outlet box.
(Choose one group of suitable mounting screws among three groups in the hardware pack)
Note: For the best performance, install fixture at 8 feet ~12 feet (2.4~3.6m) above the ground.
2. Unscrew ball nuts on the light fixture in order to remove the mounting bracket on the back of the light fixture
Thread fixture wires through gasket, and then attach the gasket to the back of mounting bracket
3. Connect the source wires from the outlet box with the power supply wire of light fixture using wire nuts as follows:
Conect the white wire to white
Conect the black wire to black
Note: DO NOT connect electricity before installation and maintaince
4. Place mounting bracket against the outlet box, insert the mounting bracket screw through the mounting bracket hole, thread mount-
ing bracket screw into the center hole of the mounting bar. Tighten the mounting bracket screw securely.
Note: The "UP" arrow must point upward.
5. Attach the back plate of the light fixture to the mounting bracket; secure it with the ball nuts
6. Use silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface to prevent water from
seeping into the outlet box.
securit y
www.homezonesecurity.com
A
D
1PC
1PC
Light fixture
Mounting bracket screw
B
E
1PC
6PCS
Mounting bar
Mounting screw
C
F
1PC
3PCS
EVA gasket
Wire nut
(3groups)
Sensor
Mounting Bar
Mounting Bracket
Outlet Box
Back Plate
Mounting Screw
Gasket
Wire Nut
Light Head
Ball Nut
Mounting
Bracket Screw
FRONT

Curved Head Security Light
[phone]
• Swing the lamp heads horizontal or vertical to adjust the
light coverage area.
Note: Keep the light head 30 degrees below horizontal to
avoid water damage and electrical shock
• Gently grasp the motion sensor and rotate it horizontal so
the controls are facing mounting bracket and two dots are
in alignment.
• Clean periodically with soft cloth.
• Do not use any cleaners with chemicals, solvents or harsh abrasives on this light. Do not use scouring pads, powders, steel
wool or brasive paper. They could cause deterioration of the finish.
HOW IT WORKS
CLEANING AND MAINTENANCE
Model No. ES06508V
securit y
www.homezonesecurity.com
Adjusting the lamp heads and motion sensor
• LUX is adjustable, by rotating the ""LUX"" knob clockwise,
the corresponding light intensity value is larger, and vice
versa
• MOTION SENSITIVITY is adjustable, by rotating the "SENS"
knob. Walk through the detection zone at the farthest
distance you wish to detect motion.
Note: Approximate range for each setting from 9feet to
40feet
• STAND-BY time is adjustable (5s ~ 3minutes), by rotating
the "TIME" knob clockwise, the corresonding delay time is
longer, and vice versa
Note: Set the "LUX" knob in " " mode to test lighting and
sensitivity
• MANUAL OVERRIDE the motion sensor continuous on at
night. The light will turn off automatically at dawn.
- To turn manual override on, turn the wall switch "OFF", then
turn it ""ON"" within 3 seconds, the light will remain on all
night long.
- To turn manual override off, turn thre wall switch ""OFF"",
then turn it ""ON"" within 3 seconds again, the light will
reset to motion sensor mode.
Product Function Description
Motion Sensor Dot
Mounting Bracket
LUX SENS TIME