HOMEDEPOT 265A User manual

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
ASSEMBLY INSTRUCTIONS
Description
Item No.
: MISSION ARM CHAIR
: 265A

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Chair back
1
B
Seat Frame
1
C
Chair Seat
1
D
Front Leg
(L-R)
2
E
Side Stretcher
(L-R)
2
F
Middle
Stretcher
1
G
Arm
(L-R)
2

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short bolt
(M6 x 40mm)
3
2
Medium bolt
(M6 x 60mm)
4
3
Long bolt
(M6 x 80mm)
4
4
Short Screw
(M3.5 x 15mm)
2
5
Medium Screw
(M4 x 35mm)
4
6
Long Screw
(M4 x 50mm)
6
7
Lock Washer
(6.5 x 11mm)
15
8
Large Flat Washer
(6.5 x 19mm)
13
9
Allen Key
(M4 x 30mm x110mm)
1
10
Hexagon nut
(M6 x 10mm)
2
11
Wrench
(10mm)
1
12
Small Flat Washer
(6.5 x13mm)
2
13
Wood Plug
(14.5)
2
14
Long bolt
(M6 x 90mm)
2

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
STEP 1
Attach seat frame (B) to the back (A) with bolts (1) and (3), and washers (7) and (8) as shown below.
Tighten with Allen key (9).
Note: DO NOT tighten any of the bolts, until the chair is assembled, then put on a flat level surface to
make sure the chair is level and then tighten the bolts.
STEP 2
Attach front legs (D) to the seat frame (B) with bolts (2), and washers (7) and (8) as shown below. Tighten
with Allen key (9).
Attach middle stretcher (F) to side stretchers (E) with screws (4). Then attach side stretchers (E) to
front and back legs with screws (6) as shown below. Tighten with a screwdriver.

ITEM NO.: 265A
REVISED APR 24, 2018
Printed in Vietnam
STEP 3
Attach arms (G) to seat frame (B) with bolts (14), and washers (7) and (12) as shown below. Tighten
with the Allen key (9).
Then use nuts (10), and washers (7) and (8) as shown below. Tighten with wrench (11).
Attach arms (G) to the chair back with screws (6). Tighten with a screwdriver.
STEP 4
Attach the seat (C) to top of the seat frame (B) with screws (5) as shown below. Tighten with a
screwdriver.
Then insert wood plugs (13) over bolts to cover them.