Homelite VERSA TOOL UT20811E User manual

OPERATOR'S MANUAL
25cc String Trimmer
Versa Tool™ Model No. UT20811E
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your new trimmer has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation, and
operatorsafety.Properly cared for,it will give youyearsof rugged, trouble-freeperformance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for buying a Homelite trimmer.

Page 2
■■
■■
■Introduction .................................................................................................................................................................2
■■
■■
■Important Safety Instructions .................................................................................................................................2 - 3
■■
■■
■Symbols ...................................................................................................................................................................... 4
■■
■■
■Specifications.............................................................................................................................................................. 5
■■
■■
■Unpacking ................................................................................................................................................................... 5
■■
■■
■Features ...................................................................................................................................................................... 5
■■
■■
■Assembly ...............................................................................................................................................................6 - 7
■■
■■
■Operation.............................................................................................................................................................. 8 - 10
■■
■■
■Maintenance ....................................................................................................................................................... 12 - 13
■■
■■
■Troubleshooting................................................................................................................................................... 14 - 15
■■
■■
■Warranty ............................................................................................................................................................. 16 - 18
■■
■■
■Service Parts............................................................................................................................................................. 19
■■
■■
■Parts Ordering / Service ............................................................................................................................................ 20
WARNING
Do not attempt to operate this trimmer until you have read thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to comply can result in accidents involving fire, electric shock,
or serious personal injury. Save operator's manual and review frequently for continuing safe operation, and
instructing others who may use this tool.
Trimming weeds and grass is an easy task using this Homelite string trimmer.Safety, performance, and dependability have
been given top priority in the design of this string trimmer making it easy to maintain and operate.
IMPORTANTSAFETYINSTRUCTIONS
INTRODUCTION
TABLE OF CONTENTS
READ ALL INSTRUCTIONS
GENERAL SAFETY RULES
■Forsafe operation, readandunderstandallinstructions
before using the trimmer. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
■Do not allow children or untrained individuals to use this
unit.
■■
■■
■Never start or run the engine in a closed or poorly
ventilated area; breathing exhaust fumes can kill.
■■
■■
■Clear the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
canbe thrown orbecome entangled inthe string heador
blade.
■■
■■
■Weareyeandhearingprotectionwhileoperatingthis
unit.
■■
■■
■Wear heavy long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, jewelry of any kind, or
gobarefoot.

Page 3
■■
■■
■Product users on United States Forest Service land, and
in some states, must comply with fire prevention regula-
tions. This product is equipped with a spark arrestor;
however,otheruserrequirementsmayapply.Checkwith
your federal, state, or local authorities.
■■
■■
■Wear eye protection which is marked to comply with
ANSIZ87.1aswellashearing protection when operating
thisequipment.
■■
■■
■Wear heavy long pants, shoes, and gloves.
■■
■■
■Keep all bystanders, children, and pets at least 50 feet
(15m)away.
■■
■■
■Do not wear loose clothing, or jewelry.
■■
■■
■Secure long hair so it is above shoulder level to prevent
entanglementin any movingparts.
■■
■■
■Do not operate this trimmer when you are tired, ill, or
under the influence of alcohol, drugs, or medication.
■■
■■
■Donotoperateinpoorlighting.
■■
■■
■Keepfirm footing andbalance. Do notoverreach.
Overreaching can result in loss of balance or exposure
to hot surfaces.
■■
■■
■Keep all parts of your body away from any moving part.
■■
■■
■Do not touch area around the muffler or cylinder of the
trimmer, these parts get hot from operation.
■■
■■
■Always stop the engine and remove the spark plug wire
before making any adjustments or repairs except for
carburetoradjustments.
■■
■■
■Ithas been reportedthat vibrations fromhand-held tools
may contribute to a condition called Raynaud’s Syn-
drome in certain individuals. Symptoms may include
tingling, numbness and blanching of the fingers, usually
apparentuponexposuretocold.Hereditaryfactors,
exposure to cold and dampness, diet, smoking and work
practices are all thought to contribute to the development
of these symptoms. It is presently unknown what, if any,
vibrations or extent of exposure may contribute to the
condition. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
a) Keepyour bodywarmincold weather.Whenoperat-
ing the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major
factorcontributingtoRaynaud’sSyndrome.
IMPORTANTSAFETYINSTRUCTIONS
b) After each period of operation, exercise to increase
bloodcirculation.
c) Take frequent work breaks. Limit the amount of
exposureperday.
d) Keepthe tool well maintained,fastenerstightened
andwornpartsreplaced.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician
about these symptoms.
■■
■■
■Mix and store fuel in a container approved for gasoline.
■■
■■
■Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 30 ft. (9 m) away from
refuelingsitebeforestartingengine.
■■
■■
■Stopthe engine andallow tocool before refuelingor
storing the unit.
■■
■■
■Allow the engine to cool; empty the fuel tank and secure
the unit from moving before transporting in a vehicle.
SPECIFIC SAFETY RULES FOR TRIMMER USE
■■
■■
■Replace string head if cracked, chipped, or damaged in
any way. Be sure the string head is properly installed
and securely fastened. Failure to do so can cause
seriousinjury.
■■
■■
■Make sure all guards, straps, deflectors and handles are
properlyandsecurelyattached.
■■
■■
■Useonly the manufacturer's replacement stringin the
cutting head. Do not use any other cutting attachment.
■■
■■
■Never operate unit without the grass deflector in place
andin good condition.
■■
■■
■Maintaina firm gripon both handleswhile trimming.Keep
string head below waist level. Never cut with the string
head located over 30 in. (76 cm) or more above the
ground.

Page 4
Important:Some of thefollowingsymbolsmaybeusedonyourtool. Please study themandlearntheirmeaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Indicatesdanger,warningorcaution.Itmeans
attention!!! Your safety is involved.
Read Your Operator’s Manual Your manual contains special messages to
bring attention to potential safety concerns,
machine damage as well as helpful operating and
servicing information. Please read all the
information carefully to avoid injury and machine
damage.
Weareyeandhearingprotection. Wear eye protection which is marked to comply
with ANSI Z87.1 as well as hearing protection
whenoperatingthisequipment.
Keepbystandersaway. Keep all bystanders at least 50 feet (15 m)
away.
Ricochet. DangerofRicochet.
Noblade. Do not install any type of blade on this unit.
SYMBOLS
Thepurpose ofsafety symbols is to attractyour attention to possible dangers.The safety symbols, and theexplanations
with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any
danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
SAVE THESE INSTRUCTIONS

Page 5
Weight-(withoutfuel) ............................................................................................................................9.1 lbs. (4.13 kg.)
Cuttingswath............................................................................................................................................17 in. (432 mm)
Enginedisplacement ................................................................................................................................................25 cc
Stringdiameter ........................................................................................................................................080 in. (2.0 mm)
FEATURES
SPECIFICATIONS
FEATURES
Fig. 1
THROTTLE TRIGGER
STARTER GRIP
CHOKE LEVER
THROTTLE CONTROL
AND REAR HANDLE
FRONT HANDLE
UPPER SHAFT
HOUSING
STRING HEAD
GRASS DEFLECTOR
IGNITION SWITCH
COUPLER
KNOB
LOWER SHAFT
HOUSING
FEATURES
UNPACKING
INSTRUCTIONS
■■
■■
■Carefullyremove the product from thecarton.
■■
■■
■Inspect the product to make sure no breakage or
damageoccurredduringshipping.
■■
■■
■Do not discard the packing material until you have
inspectedandoperatedtheproduct.
■■
■■
■If any parts are damaged or missing, please call
1-800-chainsaw(1-800-242-4672)forassistance.
PACKING LIST
■■
■■
■TrimmerAssembly
■■
■■
■Owner’sKit
■■
■■
■Fronthandle
■■
■■
■GrassDeflector
■■
■■
■Hangercap
■■
■■
■HardwareBags(2)
■■
■■
■Bottle of 2-Cycle Oil
■■
■■
■Operator'smanual

Page 6
ASSEMBLY
ATTACHING THE POWER HEAD TO THE
TRIMMER ATTACHMENT
See Figure 5.
REMOVING THE ATTACHMENT FROM THE
POWER HEAD
Forremoving or changingtheattachment:
1. Loosentheknob.
2. Push in the button and twist the shafts to remove and
separateends.
ATTACHING THE STORAGE HANGER
See Figure 6.
There are two ways to hang your attachment for storage.
■■
■■
■To use the hanger cap, push in the button and place the
hanger cap over end of the lower end attachment shaft.
Slightly rotate the cap from side to side until the button
locks into place.
■■
■■
■The secondary hole in the attachment shaft can be used
forhanging purposes as well.
WARNING:
Be certain the knob is fully tightened before operating
equipment; check it periodically for tightness during use
to avoid serious injury.
The trimmer attachment connects to the power head by
means of a coupler device.
1. Loosen the knob on the coupler of the power head shaft.
2. Push in the button located on the trimmer attachment
shaft. Align the button with the guide recess on the
power head shaft and slide the two shafts together.
Rotate the trimmer attachment shaft until the button
locks into the positioning hole.
NOTE: If the button does not release completely in the
positioning hole, the shafts are not locked into place.
Slightlyrotatefromsidetosideuntilthebuttonislockedinto
place.
3. Tighten the knob securely.
WARNING:
Neverattach oradjust any attachmentwhile power headis
running. Failure to stop the engine can cause serious
personal injury.
Fig. 2
COUPLER
KNOB
TRIMMER ATTACHMENT
UPPER SHAFT
HOUSING
POSITIONING
HOLE
GUIDE RECESS
Fig. 3
BUTTON
HOLE
HANGER CAP

Page 7

 
   
  

  
      

 


 

 

 
   
 

Ifyourunithasbeenpreassembled,checkeachsteptomake
sure the unit has been properly assembled.
HANDLE
See Figure 4.
1. Remove the front handle, bolt, flat washer, lock washer,
and wing nut from the Owner’s Kit.
2. Install the front handle onto the top side of the drive
shaft housing and move it to a comfortable position.
3. Place the bolt through the front handle as shown, then
install the flat washer, lock washer, and wing nut.
4. Tightenwing nut securely.
GRASS DEFLECTOR
See Figure 5.
1. Remove wing nut, flat washer, lock washer, and bolt
from the Owner’s Kit.
2. Place grass deflector over shaft and bracket.
3. Install bolt through the slots in the tabs on grass deflec-
tor and bracket on driveshaft housing.
4. Install flat washer, lock washer and wing nut.
5. TightenSecurely.
ASSEMBLY
GRASS
DEFLECTOR
BRACKET
BOLT
WING NUT Fig. 5
FLAT
WASHER
LOCK WASHER
WING
NUT
FRONT HANDLE
BOLT
Fig. 4
LOCK
WASHER
FLAT
WASHER

Page 8
FUELING AND REFUELING THE TRIMMER
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
pre-mixinggasoline and 2-cycle oil. Pre-mixunleaded
gasoline and 2-cycle engine oil in a clean 1 gallon container
approvedforgasoline.
Recommended fuel: This engine is certified to operate on
unleadedgasolineintended for automotive use.
Mix Homelite Premium Exact Mix oil with gasoline accord-
ing to the instructions on the package. If Premium Exact
Mix oil is not available, use a high quality 2-cycle engine
oil, mixed at 2.6 oz. per gallon (US).
Do not use automotive oil or 2-cycle outboard oil.
NOTE: Premium Exact Mix fuelmixwill stay fresh up to30
days.
DONOTmixquantitieslargerthanusableina30dayperiod.
FUEL MIXTURE
WARNING:
Always shut off engine before fueling. Never add fuel
to a machine with a running or hot engine. Move at
least 30 ft. (9 m) from refueling site before starting
engine. Do not smoke!
OPERATING THE TRIMMER
See Figure 6.
Holdthe trimmer withthe right handon the rearhandle and
the left hand on the front handle.Keep a firm grip with both
handswhile in operation.Trimmer shouldbe held ata
comfortablepositionwith therear handle abouthip height.
Always operate trimmer at full throttle. Cut tall grass from
thetop down.This willpreventgrass from wrappingaround
the driveshaft housing and string head which may cause
damagefromoverheating. If grass becomeswrapped
aroundthe string head,STOPTHEENGINE, disconnect
thespark plug wire,andremove the grass.Prolonged
cutting at partial throttle will result in oil dripping from the
muffler.
FILLING TANK
1. Cleansurface around fuelcap to preventcontamination.
2. Loosen fuel cap slowly. Rest the cap on a clean surface.
3. Carefully pour fuel into the tank. Avoid spillage.
4. Prior to replacing the fuel cap, clean and inspect the
gasket.
5. Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
PREMIUM EXACT MIX (50:1)
GASOLINE OIL
1gallon(US) 2.6 oz.
1Liter 20 cc (20 ml)
Fig. 6
OPERATION





    






 

 

  







    



Page 9
ADVANCING THE STRING
ADVANCING STRING USING THE EZ LINE™ TAP
ADVANCE SYSTEM
String advance is controlled by tapping string head on grass
whilerunning engine atfullthrottle.
1. Run engine at full throttle.
2. Tap string head on ground to advance string. String
advances each time the head is tapped.
3. Several taps may be required until string strikes the cut
off blade.
4. Resumetrimming.
NOTE: If the string is worn too short you may not be able to
advance the string by tapping it on the ground.If so, STOP
THEENGINE, and manually advance thestring.
ADVANCING THE STRING MANUALLY
Pushthe spoolretainer down whilepulling on string(s) to
manuallyadvance thestring.
CUT OFF BLADE
This trimmer is equipped with a cut-off blade on the grass
deflector.For best cutting, advance string until it is trimmed
to length by the cut-off blade. Advance string whenever you
hearthe engine running fasterthan normal.This willmain-
tainbest performance andkeep string longenoughto
advanceproperly.
CUTTING TIPS
See Figure 7.
■Keep the trimmer tilted toward the area being cut; this is
the best cutting area.
■Do not cut in dangerous cutting area.
■Use the tip of string to do the cutting; do not force string
head into uncut grass.
■Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may
wearstringrapidly.
■Avoid trees and shrubs. Tree bark, wood moldings,
siding, and fence posts can easily be damaged by the
string.
OPERATION
BEST CUTTING
AREA
DANGEROUS
CUTTING AREA Fig. 7

Page 10
1
2
3
STARTING AND STOPPING
See Figure 8 and 9.
TO START A COLD ENGINE:
1. Lay the trimmer on a flat, bare surface.
2. Make sure the switch is in the run “I” position.
2. Push the primer bulb 8 to 10 times.
3. Set the choke lever to the choke position .
4. Squeeze the throttle trigger to the full throttle position.
5. Pull the starter until the engine tries to run. No more
than 6 pulls.
6. Set the choke lever to the half choke position .
7. Hold the trigger and the pull starter rope until the engine
runs.
8. Run the engine 30 to 45 seconds at full throttle (with the
trigger depressed fully) on half choke position to
warm up the engine. Move the choke lever to the run
position .
TO START A WARM ENGINE:
1. Move the choke lever to the run position .
2. Hold the trigger and pull the starter rope until the engine
runs.
TO STOP THE ENGINE:
To stop the engine, press and hold the switch in the STOP
position“O”.
HALF
CHOKE
POSITION
PRIMER BULB
CHOKE LEVER
CHOKE
POSITION
RUN POSITION
Fig. 9
OPERATION
IGNITION SWITCH
I = ON TO RUN
O = OFF TO STOP
Fig. 8
THROTTLE
TRIGGER
THROTTLE INTERLOCK

Page 11
WARNING:
Useonlyoriginalmanufacturer'sreplacementparts,
accessories and attachments. Failure to do so may
cause poor performance, possible injury and may
voidyourwarranty.
Fig.10
Fig.11
SPOOL
RETAINER
SPRING
SLOTS
STRING HEAD
EYELETS
DRIVESHAFT
MAINTENANCE
You can often make adjustments and repairs described
here.For otherrepairs, have the trimmer servicedby an
authorizedservice dealer.
SPOOL REPLACEMENT
EZ LINE™ TAP ADVANCE SYSTEM
NEW PREWOUND SPOOL
SeeFigures 10and 11.
If replacing string only, refer to “String Replacement”later in
this manual.
Useonly .080 in.(2.0 mm) diametermonofilamentstring.
Useoriginal manufacturer's replacement stringforbest
performance.
1. Stop the engine, disconnect the spark plug wire. Hold
thestringheadand unscrew the spoolretainer.Turn
counterclockwise.
2. Remove the empty spool from the string head. Keep the
spring attached to the spool.
3. To install the new spool, make sure the two strings are
captured in the slots opposite each other on the new
spool. Make sure the ends of each string is extended
approximately 6 in. (152 mm) beyond each slot.
4. Thread the strings into the eyelets in the string head.
Carefully push the spool into the string head (gently pull
the strings to the outside if necessary). When the spool
is positioned in the string head, grasp the strings and
pull sharply to release them from the slots in the spool.
5. Push down and turn the spool counterclockwise until it
no longer turns. Hold the spool down and rotate clock-
wise a small amount. Release the spool. The spool
should be locked down in the string head. If not, hold
downand rotate untillocked.
6. Make sure the string head and the spool retainer are
installed on the drive shaft by turning the retainer
clockwise to tighten.
7. Pull the strings again to rotate the spool into cutting
position.Push the spoolretainerdown while pullingon
string(s) to manually advance the string and to check for
proper assembly of the string head.

Page 12
STRING REPLACEMENT
See Figures 12, 13, 14, and 15.
1. Stop the engine, disconnect the spark plug wire.
Holdthestring head and unscrewthe spoolretainer.
Turncounterclockwise.
2. Remove the spool from the string head. NOTE:
Keep the spring attached to the spool. Remove any
old string remaining on the spool.
3. Cut two pieces of string, each being approximately
9 ft. (2.7 m) long. Use only .080 in. (2.0 mm)
diametermonofilamentstring.
4. Insert the first string into the anchor hole in the
upper part of the spool. Wind the first string around
the upper part of the spool counterclockwise, as
shown by the arrows on the spool. Place string in
the slot on upper spool flange, leaving about 6 in.
(152 mm) extended beyond the slot. Do not overfill.
After winding the string, there should be at least 1/4
in. (6 mm) between the wound string and the outside
edge of the spool.
5. Repeat above step with second string, using the
bottom part of spool. Do not overfill.
6. Replacethe spool andthe spool retainer. Refer to
"Spool Replacement " earlier in this manual.
CLEANING THE EXHAUST PORT AND
MUFFLER
NOTE: Depending on the type of fuel used, the type
andamount of oilused,and/or your operatingcondi-
tions, the exhaust port and muffler may become
blocked with carbon deposits. If you notice a power
loss with your gas powered tool, you may need to
remove thesedeposits to restoreperformance.We
highlyrecommended that onlyqualified service techni-
cians perform this service.
SPARK ARRESTOR
Thespark arrestor must be cleanedor replaced every
25hours or yearlytoensure proper performanceof your
product. Spark arrestors may be in different locations
dependingonthe model purchased.Pleasecontact
your nearest service dealer for the location of the spark
arrestorforyourmodel.
CleaningInstructions:
■■
■■
■Remove the spark arrestor from the muffler.
■■
■■
■If your spark arrestor is made of a fiberglass mate-
rial,discardandreplace.
■■
■■
■If your spark arrestor is made of a metal material
follow these cleaning instructions:
1. Spray the spark arrestor with a quality carbon
cleaner.
2. Gently clean using a wire brush.
3. Install the new or cleaned spark arrestor and
reassemblecompletelybeforeuse.
MAINTENANCE
Fig.14
Fig.15
SPRING
Fig.13
SLOT ARROWS ON
SPOOL
SECOND
STRING
FIRST STRING Fig.12
SPOOL
ANCHOR
HOLE
ARROWS ON
SPOOL
FIRST STRING
SLOT

Page 13
2
1
3

 

  




    




The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine perfor-
mance. If performance improves when the fuel cap is
loosened, check valve may be faulty or filter clogged.
Replacefuel cap ifrequired.
SPARK PLUG
This engine uses a Champion RCJ-6Y with .025 in.
(0,63 mm) electrode gap.Use anexact replacementand
replace annually, or more frequently if necessary.
STORING THE TRIMMER (1 MONTH OR
LONGER)
1. Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
2. Clean all foreign material from the trimmer. Store it in a
well-ventilated place that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
3. Abide by all Federal and local regulations for the safe
storage and handling of gasoline. Excess fuel should be
usedupinother2-cycleenginepoweredequipment.
REPLACING AND CLEANING AIR FILTER
SeeFigures 16and 17.
Forproper performance andlong life, keepair filter clean.
1. Remove the air filter cover by pushing down on the latch
with your thumb while gently pulling on the cover.
2. Remove the filter, clean it in warm soapy water. Rinse
and let dry completely. For best performance, replace
annually.
3. Install the filter, align tabs, push in, and make sure the
latch snaps and latches into place.
FUEL CAP
WARNING:
A leaking fuel cap is a fire hazard and must be
replacedimmediately.
AIR FILTER
COVER
FILTER
Fig.16
Fig. 17
MAINTENANCE
LATCH
PULL COVER
TO OPEN

Page 14
PROBLEM POSSIBLE CAUSE SOLUTION
1. To check for spark: Disconnect the spark plug
wire. Reattach the spark plug wire and lay spark
plug on metal cylinder. Pull the starter rope and
watch for spark at spark plug tip. If there is no
spark, repeat test with a new spark plug.
2. Push primer bulb until bulb is full of fuel. If
bulb does not fill, primary fuel delivery system
is blocked. Contact a service dealer. If primer
bulb fills, engine may be flooded (see next
item).
3. Remove spark plug, turn trimmer so spark plug
hole is aimed at the ground. Move choke lever
to “RUN” and pull starter cord 10 to 15 times.
This will clear excess fuel from engine. Clean
and reinstall spark plug. Pull starter three
times with choke lever at “RUN”. If engine
does not start, move choke lever to “CHOKE”
andrepeatnormalstartingprocedure.Ifengine
still fails to start, repeat procedure with a new
sparkplug.
4. Contact a service dealer.
Contact a service dealer.
Turnmixture needle counterclockwise1/16 turn.
SeeFigure18.
1. Use fresh fuel and the correct 2-cycle oil mix.
2. Clean air filter. Refer to “Replacing and
CleaningAir Filter” earlierinthis manual.
3. Turn mixture needle clockwise 1/16 turn. See
Figure18.
Turn idle speed screw clockwise to increase idle
speed. SeeFigure18.
1. Lubricate with silicone spray.
2. Install more string. Refer to “String Replace-
ment”earlier inthis manual.
3. Pull strings while alternately pressing down on
andreleasingspoolretainer.
4. Removestringfrom spool andrewind.Refer to
“StringReplacement”earlierinthismanual.
5. Advance string at full throttle.
Engine will not start:
Engine starts but will not
accelerate:
Engine starts but will only
run at high speed at half
choke:
Engine does not reach full
speed and emits excessive
smoke:
Engine starts, runs, and
accelerates but will not
idle:
String will not advance:
1. Nospark.
2. Nofuel.
3. Floodedengine.
4. Starterropepullshardernowthan
whennew.
Carburetorrequiresadjustment.
Carburetorrequiresadjustment.
1. Check oil fuel mixture.
2. Air filter dirty.
3. Carburetorrequiresadjustment.
Carburetorrequiresadjustment.
1. String welded to itself.
2. Notenoughstringon spool.
3. Stringworn too short.
4. Stringtangledonspool.
5. Enginespeed too slow.
TROUBLESHOOTING

Page 15
1
2
3
PROBLEM POSSIBLE CAUSE SOLUTION
Fig.18
1. Cut tall grass from the top down.
2. Operate trimmer at full throttle.
Cleanthreads and lubricatewithgrease - ifno improve-
ment,replacespoolretainer.
1. Operate trimmer at full throttle.
2. Use fresh fuel and the correct 2-cycle oil mix.
3. Cleanair filter. Refer to “Replacing and Cleaning Air
Filter” earlier in this manual.
4. Turn mixture needle clockwise 1/16 turn. SeeFigure
18.
1. Cutting tall grass at ground
level.
2. Operatingtrimmeratpart
throttle.
Screwthreadsdirtyordamaged.
1. Operatingtrimmeratpart
throttle
2. Check oil/fuel mixture.
3. Air filter dirty.
4. Carburetorrequiresadjust-
ment.
Grasswrapsaround
driveshafthousingand
stringhead:
Spoolretainerhardto
turn:
Oil drips from muffler:
NOTE:This engine complieswithEPA (Environmental Protec-
tionAgency)and CARB (CaliforniaAirResource Board)
regulationswhich require exhaustemission control. Asa
result,thecarburetor adjustment needle(s) areequippedwith
plastic cap(s) that limit the rotation from the original factory
adjustment. If your unit exhibits specific performance
problem(s)where theTroubleShooting Section recommendsa
needle adjustment and you are at the limit of adjustment, the
unit should be taken to a factory authorized service dealer for
repair.
TROUBLESHOOTING
MIXTURE
NEEDLE
IDLE SPEED
SCREW

Page 16
WARRANTY
LIMITED WARRANTY STATEMENT
HomeliteConsumerProduct,Inc.warrantstotheoriginalretail
purchaserthatthisHOMELITEproductisfreefrom defect in
materialandworkmanshipandagreestorepairorreplace,at
HomeliteConsumerProducts,Inc.’sdiscretion,anydefective
productfreeofchargewithinthesetimeperiodsfromthedateof
purchase.
■■
■■
■Oneyearforthefollowingunits:UT08110,UT20760,UT10901;
■■
■■
■Twoyearsforallother Homeliteproducts,iftheproductis used
forpersonal,familyorhouseholduse;
■■
■■
■90 days, if any of the above products are used for any other
purpose,suchas commercialorrental.
Thiswarrantyextendstotheoriginalretailpurchaseronlyand
commencesonthedateoftheoriginalretailpurchase.
AnypartoftheHOMELITEproductmanufacturedorsuppliedby
HOMELITEandfoundinthereasonablejudgmentofHOMELITEto
bedefectiveinmaterialorworkmanshipwillberepairedorreplaced
byanauthorizedHOMELITEservicedealerwithoutchargefor
partsandlabor.
TheHOMELITEproductincludinganydefectivepartmustbe
returnedtoanauthorizedservicedealerwithinthewarrantyperiod.
TheexpenseofdeliveringtheHOMELITEproducttothedealerfor
warrantyworkandtheexpenseof returning it back to the owner
afterrepairorreplacementwillbepaidbytheowner.HOMELITE’S
responsibilityinrespecttoclaimsislimitedtomakingtherequired
repairsorreplacementsand noclaimofbreachof warrantyshallbe
cause for cancellation or rescission of the contract of sale of any
HOMELITEproduct.Proofofpurchasewillberequiredbythe
dealertosubstantiateanywarrantyclaim.Allwarrantyworkmust
beperformedbyanauthorizedHOMELITEservicedealer.
Thiswarrantyislimitedtoninety(90)daysfromthe dateoforiginal
retailpurchaseforanyHOMELITE productthatisusedforrentalor
commercialpurposes,oranyotherincome-producingpurpose.
Thiswarrantydoes not cover any HOMELITE product that has
beensubjecttomisuse,neglect,negligence,oraccident,orthat
hasbeenoperated inanywaycontrary totheoperatinginstructions
asspecifiedintheHOMELITEoperator’smanual.Thiswarranty
doesnotapplytoanydamageto theHOMELITE productthatisthe
resultofimpropermaintenanceortoanyHOMELITEproductthat
hasbeenalteredormodified.Thewarrantydoesnotextendto
repairs made necessary by normal wear or by the use of parts or
accessorieswhichareeitherINCOMPATIBLEWITHTHE
HOMELITEproductoradverselyaffectitsoperation,performance
ordurability.
Inaddition,thiswarrantydoesnotcover:
A. Tune-ups–SparkPlugs,Carburetor,CarburetorAdjustments,
Ignition,Filters
B. Wearitems–BumpKnobs/SpoolRetainers,OuterSpools,Cutting
Lines,InnerReels,StarterPulley,StarterRopes,DriveBelts
HOMELITEreservestherightto changeorimprovethedesign of
anyHOMELITEproductwithoutassuminganyobligationtomodify
anyproductpreviouslymanufactured.
ALLIMPLIEDWARRANTIESARELIMITEDINDURATIONTO
THESTATEDWARRANTYPERIOD.ACCORDINGLY,ANYSUCH
IMPLIEDWARRANTIESINCLUDINGMERCHANTABILITY,
FITNESSFORAPARTICULARPURPOSE,OROTHERWISE,
AREDISCLAIMEDINTHEIRENTIRETYAFTERTHE
EXPIRATIONOFTHEAPPROPRIATETWO-YEAR,ONE-YEAR,
ORNINETYDAYWARRANTYPERIOD.HOMELITE’S
OBLIGATIONUNDERTHISWARRANTYISSTRICTLYAND
EXCLUSIVELYLIMITEDTOTHEREPAIRORREPLACEMENT
OFDEFECTIVEPARTSANDHOMELITEDOESNOTASSUME
ORAUTHORIZEANYONETOASSUMEFORTHEMANYOTHER
OBLIGATION.SOMESTATESDONOTALLOWLIMITATIONS
ONHOWLONGANIMPLIEDWARRANTYLASTS,SOTHE
ABOVELIMITATIONMAYNOTAPPLYTOYOU.HOMELITE
ASSUMESNORESPONSIBILITYFORINCIDENTAL,
CONSEQUENTIALOROTHERDAMAGESINCLUDING,BUTNO
LIMITEDTOEXPENSEOFRETURNINGTHEHOMELITE
PRODUCTTOANAUTHORIZEDSERVICEDEALERAND
EXPENSEOFDELIVERINGITBACKTOTHEOWNER,
MECHANIC’STRAVELTIME,TELEPHONEORTELEGRAM
CHARGES,RENTALOFALIKEPRODUCTDURINGTHETIME
WARRANTYSERVICEISBEINGPERFORMED,TRAVEL,LOSS
ORDAMAGETOPERSONALPROPERLY,LOSSOFREVENUE,
LOSS OF USE OF THE PRODUCT, LOSS OF TIME, OR
INCONVENIENCE,SOMESTATESDONOTALLOWTHE
EXCLUSIONORLIMITATIONOFINCIDENTALOR
CONSEQUENTIALDAMAGES,SOTHEABOVELIMITATIONOR
EXCLUSIONMAYNOTAPPLYTOYOU.
Thiswarrantygivesyouspecific legal rights, any you may also
have other rights which vary from state to state.
ThiswarrantyappliestoallHOMELITEproductsmanufacturedby
HOMELITEandsoldintheUnitedStatesandCanada.
Tolocateyournearestservicedealer,dial1-800-242-4672orlog
ontoourwebsiteatwww.homelite.com.

Page 17
WARRANTY
LIMITED WARRANTY FEDERAL EMISSION CONTROL SYSTEMS - NON-ROAD AND
SMALL OFF-ROAD ENGINES
TheU.S.Environmental Protection Agency (EPA) and Homelite Consumer Products,Inc.are pleasedto explaintheEmission Control System
Warrantyon your nonroad or small off-road engine. 1997 andlater model year nonroad enginesmust be designed, builtand equipped, at the
timeof sale,tomeet the U.S.EPAregulations for small nonroad engines.The nonroadengine mustbe free from defectsinmaterials and
workmanship which cause it to fail to conform with U.S.EPA standards for the first two years of engine use from the date of sale to the
ultimate purchaser.Homelite Consumer Products, Inc.must warrant the emission control system on your nonroad or small off-road engine for
theperiod of time listed above provided therehas been no abuse, neglect, or improper maintenance of your nonroad or small off-roadengine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, the catalytic converter.
Alsoincluded may be hoses, belts, and connectors and other emission related assemblies.Where a warrantable condition exists, Homelite
Consumer Products, Inc. will repair your nonroad or small off-road engine at no cost to you, including diagnosis (if the diagnostic work is
performedat an authorizeddealer),parts,andlabor.
MANUFACTURER'SWARRANTY COVERAGE:
1997andlatermodelyearnonroad engines are warranted for two years. If any emission-related part on your engineisdefective,thepart will be
repaired or replaced by Homelite Consumer Products, Inc. free of charge.
OWNER'SWARRANTY RESPONSIBILITIES
(a) As the nonroad or small off-road engine owner, you are responsible for the performance of required maintenance listed in your owner's
manual. HomeliteConsumer Products, Inc. recommends that you retain all receipts covering maintenance onyour nonroad or small off-
road engine, but Homelite Consumer Products, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performanceof all scheduled maintenance.Any replacement part or service that is equivalent in performance and durability may be used
innon-warrantymaintenance or repairs,andshall not reduce the warrantyobligationsofthe engine manufacturer.
(b) As the nonroad or small off-road engine owner, you should be aware, however, that Homelite Consumer Products, Inc., may deny you
warranty coverage if your nonroad or small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unap-
provedmodifications.
(c) You are responsible for presenting your nonroad or small off-road engine to a Homelite Consumer Products, Inc., service dealer as soon
as a problem exists.The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
Ifyouhaveanyquestionsregardingyourwarrantyrightsandresponsibilities,youshouldcontactaHomeliteConsumerProducts,Inc.,Customer
Representativeat 1-800-chainsaw (1-800-242-4672).
COVERAGE:
Homelite Consumer Products, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small off-road
enginewillbedesigned,builtand equipped, at thetimeofsale,tomeetallapplicableregulations. Homelite Consumer Products,Inc.alsowarrants
to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is free from defects in materials and
workmanship which cause the engine to fail to conform with applicable regulations for a period of two years.1997 and later model years, EPA
requiresmanufacturerstowarrant non-road engines fortwo years.These warrantyperiods will begin on the date the nonroad orsmall off-road
engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Homelite
Consumer Products, Inc.at no cost to the owner.
HomeliteConsumerProducts,Inc.shallremedywarrantydefectsatanyauthorizedHomeliteConsumerProducts,Inc.engine dealer or warranty
station. Any authorized work done atan authorized dealeror warranty stationshall befree of chargeto the ownerif such work determinesthat
awarrantedpartis defective. Any manufacturer-approved or equivalent replacement partmaybe used for any warranty maintenance or repairs
onemission-relatedparts,andmustbeprovidedfreeofchargetotheownerifthepart is stillunderwarranty. HomeliteConsumerProducts,Inc.
is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
EPA considers emission-relatedwarrantedparts to include all thepartslistedbelow.)Thesewarrantedparts are: Carburetor, SparkPlug,Ignition,
AirFilter and Fuel Filter.
MAINTENANCEREQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by Homelite Consumer Products, Inc. in the operator's
manual.
LIMITATIONS
TheEmission Control Systems Warranty shall not cover any of the following:
(a) repair of replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or replace-
mentsnot conforming to Homelite Consumer Products, Inc.specifications that adverselyaffectperformance and/or durability, and
alterationsor modifications not recommendedor approved in writing by Homelite Consumer Products, Inc., and
(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replace-
mentpoint.
TheEmissions Compliance PeriodreferredtoontheEmissionsCompliancelabelindicates the numberofoperatinghoursforwhichtheengine
hasbeen shown to meetFederal emission requirements. Category C=50hours, B=125 hours, andA=300 hours.

Page 18
WARRANTY
EMISSIONSMAINTENANCESCHEDULEAND WARRANTEDPARTSLIST
EmissionsParts InspectBefore CleanEvery ReplaceEvery CleanEvery
EachUse 5 Hours 25Hours orYearly 25Hours orYearly
AIRFILTERASSY
INCLUDES:
FILTER .............................................................................. X........................................... X
SPARKSCREEN ............................................................................................................................................................... X
CARBURETORASSY
INCLUDES:
HEATDAM
GASKETS
FUELTANKASSY
INCLUDES:
FUELLINES ............................ X
FUELCAP ............................... X
FUELFILTER
IGNITIONASSY
INCLUDES:
SPARKPLUG ................................................................................................................... X
ALLEMISSIONS-RELATEDPARTSAREWARRANTEDFORTWOYEARSORFORTHEPERIODOFTIME
PRIORTOTHEPARTSFIRSTSCHEDULEDREPLACEMENTWHICHEVERCOMESFIRST.

Page 19
SERVICEPARTS
P
OPTIONAL MUFFLER GUARD
G
E
H
K
F
Q
L
J
O
N
A
C
M
B
D
Forproduct information, technicalhelp,
dealerlocationsor partsordering information
visit our website at:www.homelite.com or
call1-800-chainsaw(1-800-242-4672).
P/N DESCRIPTION
A. UP04634 Muffler Assembly w/Gasket
Includes:
06502 Screen-SparkArrestor
B. 984574001 CarburetorAssembly
C. 984878001 Ignition Assembly
Includes:
PS02227 SparkPlug
D. 984876001 Air Filter Assembly
Includes:
98760 Filter
E. 984877001 Starter Assembly
F. UP00020 Fuel Tank Assembly
Includes:
A09116 FuelCap
G. PS01127 RearHousing
H. 984879001 ControlHandleAssembly
J. PS01177 Cable-Throttle
K. 06542A Handle
L. 984716001 DriveshaftAssembly -Upper
M. UP03851 Driveshaft Assembly - Lower
N. PA01014 Deflector
O. DA03001A Stringhead- Complete (.080in.[2.0mm])
Includes:
A98231A Housing & Eyelet
06713 Spring-Compression
PA0387A Spool & String (.080 in. [2.0 mm])
A98866A Retainer-Spool(R.H.Thread,Black)
P. UP04099 MufflerGuardKit(Optional)
Q. EngineAssembly

983000-294
HOMELITE CONSUMER PRODUCTS, INC.
1428PearmanDairyRoadAnderson,SC29625
Post Office Box 1207, Anderson, SC 29622
Phone1-800-chainsaw(1-800-242-4672)
www.homelite.com
OPERATOR'S MANUAL
25cc String Trimmer
Versa Tool™ Model No. UT20811E
WARNING:
The engine exhaust from this product contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm
CALIFORNIA PROPOSITION 65
SERVICE
For parts or service, contact your nearest Homelite authorized service dealer. Be sure to
provide all relevant information when you call or visit. For the location of the authorized service
dealer nearest you, please call 1-800-chainsaw (1-800-242 4672) or visit us online at
www.homelite.com.
REPAIR PARTS
The model number of this tool is found on a plate or label attached to the housing. Please
record the serial number in the space provided below.
MODEL NUMBER ____________________
SERIAL NUMBER ____________________
UT20811E