HomeSeer HS-WV100+ User manual

HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH 03110 | HomeSeer.com | Doc: HS-WV100-en-v1.0
HS-WV100+ 1.25” Z-Wave Valve Controller
Install Electronic Water Valve
The included electronic water valve must be installed into the exisng plumbing. For whole-building protecon, the valve should be
installed where it can turn o all of the water entering the premises. In a residenal seng this is typically on the main water line
coming into the house. Variaons in plumbing make it impossible to provide detailed instrucons for your installaon. Your situaon
may require reroung the water line, or other changes to your plumbing. It is your responsibility to check with your local codes de-
partment to determine if a licensed plumber is required to install the Electronic Water Valve.
*** CAUTION - Do NOT insert ngers into the valve as this may cause serious injury!
Install HS-WV100+ Z-Wave Water Valve Controller Unit
The water valve controller unit should be posioned near the electronic water valve.
1.Mount the water valve controller to the wall using appropriately sized hardware (not included).
2.Aach the electronic water valve cable to the “VALVE” connector on the water valve controller.
3.Aach the supplied power adapter to the “DC12V” connector on the water valve controller.
4.Power the system by plugging the power adapter into a wall outlet.
Z-Wave Network Installaon
Inclusion (Use this procedure to add the HS-WV100+ to your Z-Wave network).
1.Put your home automaon controller into ‘inclusion’ mode. Consult your system’s manual for details.
2.Press the “program” buon on the water valve controller unit. Wait for the process to nish.
Exclusion (Use this procedure to remove the HS-WV100+ from your Z-Wave network).
1.Put your home automaon controller into ‘exclusion’ mode. Consult your system’s manual for details.
2.Press the “program” buon on the water valve controller unit. Wait for the process to nish.
Reset (Use this procedure to reset the HS-WV100+ to factory default sengs when the network primary controller is missing or otherwise inoperable).
1.Press and hold the “program” buon on the water valve controller unit for 15 seconds. The LED will blink rapidly.
2.When the LED turns o, release the program buon. Your water valve controller unit is now reset.
OVERVIEW & INSTALLATION
HS-WV100+ is a valve controller system that is designed to control the ow of water when Z-Wave commands are received. It may be used with compable
home automaon systems (and sensors) to migate water damage when leaks are detected. It may also be used for a variety of other automated or re-
motely controlled water or irrigaon needs.
OPERATION
Remote Valve Operaon (use this procedure for remote or automac control of the water valve)
HS-WV100+ valve controller behaves like a Z-Wave “binary” device, with “ON” and “OFF” values, when added to most home automaon systems.
Open Valve - Issue “ON” command from Z-Wave controller or Z-Wave compable home automaon system.
Close Valve - Issue “OFF” command from Z-Wave controller or Z-Wave compable home automaon system.
Local Valve Operaon (use this procedure for convenient local control of the water valve)
Open Valve - Press and release the ’Open’ buon on the water valve controller unit to open the water valve.
Close Valve - Press and release the ’Close’ buon on the water valve controller unit to close the water valve.
Local Manual Valve Operaon (for use in the event of a power failure or water valve controller failure)
Our 1.25” water valve does not include a built-in manual override. We recommend plumbing a bypass loop (with manual ball valves) as part of this installa-
on to provide or prevent water ow in the event of a power failure or HS-WV100 unit failure.
Z-WAVE ASSOCIATION INFO
The HS-WV100+ has a single Associaon Group, Group 1 also known as the “Lifeline” group. Four (4) NodeIDs can be SET into Group 1. Typically the Z-
Wave system controller will be the most important member of Group 1.
SPECIFICATIONS
Operang Temp Range 5ºC to 80ºC Power Supply 12 VDC, 1A, UL (US, Canada), FCC
Z-Wave Frequency | Range 908 / 916 MHz (US) | Up To 300 Ft line of sight Valve Type Motorized Ball Valve
Controller Cercaon Z-Wave Plus Valve Cercaon NSF

HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH 03110 | HomeSeer.com | Doc: HS-WV100-en-v1.0
LED INDICATOR - The blue LED on the face of the water valve controller unit indicates the current operang mode.
LED Mode
OFF Power is o
BLINKS slowly Not joined to a Z-Wave network - Press the Z-Wave buon to join
BLINKS quickly aer
pressing Z-Wave buon
Sent a Z-Wave Node Info and aempng to either Include or Exclude from a Z-Wave network. Expires aer about 10 seconds if
not joined
BLINKs very quickly The sensors from the valve are in an invalid state. This happens while the valve is in transion or if there is a fault in the wiring.
WINKs ON If the LED is OFF most of the me and briey “winks” ON every 2 seconds, then the valve is CLOSED and the HS-SV100+ is joined
to a Z-Wave network
WINKs OFF If the LED is ON most of the me and briey “winks” OFF every 2 seconds, then the valve is OPEN and the HS-SV100+ is joined to
a Z-Wave network
TROUBLESHOOTING
PROBLEM SOLUTION
Not Powering on - No
LED lights
Check outlet for voltage:
If there is no voltage check the fuse panel for thrown breaker.
Unable to join to a Z-
Wave network
Perform a Z-Wave Exclusion on the device rst, then try re-including. If that fails, press and hold the Z-Wave buon for 30
seconds to do a full Reset to Factory Defaults.
Valve non responsive Make sure valve is plugged into Z Wave Valve Controller. If it is sll not responding to commands replace valve.
Any other quesons Contact HomeSeer (HomeSeer.com)
LIMITED WARRANTY AND DISCLAIMER
HomeSeer Technologies, LLC will repair or replace, at its opon, any part of the device, which proves to be defecve in workmanship or material under
normal use, in the USA except in the states of Alaska or Hawaii, for a period of one year from the date the device is purchased. During the warranty period,
HomeSeer Technologies, LLC will repair and provide all parts necessary to correct such defects, free of charge, provided the device has been operated in
accordance with the manufacturer's guidelines. The Customer will return the device to HomeSeer Technologies, LLC for tesng and repair or replacement.
Should you need service, during warranty period or beyond, contact HomeSeer to obtain return authorizaon before shipping your device to HomeSeer
Technologies, LLC.
Except for the obligaon to repair or replace the HS-WV100+ as stated herein, HomeSeer Technologies, LLC shall not be liable for any incidental or conse-
quenal damage caused by failure of the HS-WV100+ to funcon as adversed or expected.
HomeSeer Technologies, LLC technicians, will provide all warranty service and this warranty is void if the device has been opened or serviced by anyone
other than a HomeSeer Technologies, LLC technician.
EXCEPT FOR THE LIMITED WARRANTY AS STATED IN THIS AGREEMENT, THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, BY OPERATION OF LAW OR
OTHERWISE. HOMESEER TECHNOLOGIES, LLC DISCLAIMS THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AS TO PRODUCTS AND SERVICES SUPPLIED UNDER THIS AGREEMENT. IN NO EVENT WILL
HOMESEER TECHNOLOGIES, LLC BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO,
COMMERCIAL LOSS, PROPERTY DAMAGE, LOSS OF USE, LOSS OF REVENUES, PROFITS, OR SAVINGS, EVEN IF HOMESEER TECHNOLOGIES, LLC KNEW OR
SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES.
HomeSeer Technologies, LLC does not guarantee the leak nocaon service in regards to nocaon of leaks. HomeSeer Technologies, LLC is not respon-
sible for any value of water loss, commercial loss or any property damage, or for any other loss or damage caused or incurred as a result of the failure of
the device and/or failure of the nocaon service.
Some states do not allow the exclusion or limitaon of incidental or consequenal damages, so the above limitaons or exclusions may not apply to you.
This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state. To know what your legal rights are in your
state, consult your local or state consumer aairs oce or your state's Aorney General.
Your state laws or local ordinances may require that a licensed plumber perform installaon of this device. The manufacturer is not responsible for enforce-
ment of your states law or local ordinances.
Damage limitaon warning; In no event shall manufacture be liable for any incidental or consequenal damages including water damage, damage to other
property by water, loss of use of the product, loss of me, inconvenience, travel expense, lodging expenses, lost by damage to personal property, loss of
income, prots or revenues.