Homewerks AQUEOUS 15-U42-WNCH-AD User manual

TWO HANDLE LAUNDRY
TUB FAUCET
10-16-2013
PACKAGE AND HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
A Faucet body 1
D Mounting nuts 2
MODELS
15-U42-WNCH-AD – Chrome
15-U42-WNCH-B – Chrome
Homewerks Worldwide, LLC • Lincolnshire, IL 60069 • www.homewerksww.com
B
A
PREPARATION
SAFETY INFORMATION
Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list and hardware contents. If any
part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, Groove
Joint Pliers, Pipe Wrench, Phillips Head Screwdriver, and Supply Lines.
Installations may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot or cold water lines, then
turn on the old faucet to release built-up pressure. When installing the
new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.
Connections that are too tight will reduce the integrity of the system.
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
CAUTION
• If you solder the joints during installation of the faucet, the seats,
cartridges, and washers must be removed before using a ame
or the warranty will be voided on these parts.
• Cover the sink drain to avoid losing parts.
US

2
www.homewerksww.com
1. Turn off water at the supply
valve under the sink or at the
main water supply, disconnect
the supply line, and remove old
faucet.
Clean and dry surface area where
new faucet will be mounted.
13. Connect water supply lines.
(1) Use 1/2" IPS faucet supply
lines or (2) use coupling nuts
(not supplied) with (3) ball-nose
risers (not included).
Turn water supply or shut-off
valve back on and check for
leaks. If leaks occur, gently
tighten the faucet connections.
3
1
2
3
2. Place new faucet through holes
in top of sink. From underside,
slide mounting nuts onto threaded
rods. Secure with washer and
nuts.
24. Important: After installation is
completed, remove aerator.
Turn on water supply and allow
both hot and cold water to run
for at least one minute each.
While water is running, check
for leaks. Replace aerator.
Tighten nuts slightly to stop
minor leaks. If problems persist,
refer to troubleshooting chart.
4
PRODUCT SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
Max. Flow Rate: 2.2 GPM (8.3 LPM) at 60 PSI Washerless cartridges
ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead
content on wetted surfaces
NSF 61-9
Chrome nish Total weight of item: 1.648 lbs.
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the nish and void your warranty.

3
www.homewerksww.com
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Leaks underneath
handle.
Bonnet has come loose or
O-ring on cartridge is dirty
or twisted.
1. Move the handle to the OFF position. Unscrew the handle screw and remove the handle.
2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the on position. The
leak should stop draining out from around the cartridge stem.
3. Shut off the water supply. Remove the bonnet by turning it counterclockwise. Lift out the
cartridge valve. Inspect the larger O-ring on the cartridge bonnet and the smaller O-ring on
the cartridge stem. Remove any debris from the O-rings. If either O-ring is twisted, straighten
it out. If either O-ring is damaged, replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the two sides of
the cartridge bonnet t into the grooves on the two sides of the faucet body. Tightly screw
the bonnet onto the faucet body.
5. Re-install the handle.
Water does not
completely shut off.
Rubber valve seat is dirty,
stuck, or broken.
1. Shut off the water supply to the faucet that leaks.
2. Remove the handle on the problem side. Loosen the bonnet by turning it counterclockwise.
Lift out the cartridge assembly.
3. Inspect the rubber valve seat in the faucet body. If there is debris or brass scrap on the
surface of the seat, remove it. If the rubber seat is stuck tightly in the water inlet hole, push it
gently with a ngertip so that it moves up and down smoothly. The spring (smaller end up)
must be replaced underneath the valve seat. If the rubber valve seat is worn out or
broken, replace the cartridge by calling customer service.
4. Replace the cartridge in the faucet body. Make sure that the ridges on the two sides of the
cartridge bonnet t into the grooves on the two sides of the faucet body. Tightly screw the
bonnet onto the faucet body.
5. Re-install the handle.
Faucet leaks around
aerator.
Aerator incorrectly tted. 1. Unscrew the aerator by turning it clockwise. Inspect the black rubber packing inside the
aerator. The rubber packing should be at.
2. Screw the aerator onto the spout end and tighten.
Improper water
pattern.
Aerator dirty or small parts
inside aerator improperly
installed.
1. Remove the aerator from the spout end by turning it clockwise.
2. Gently ush the small parts inside the aerator to clear away any debris.
3. Re-install the small parts as shown in the exploded diagram. Metal screens must be at
and plastic supporter must be straight.
4. Screw the aerator onto the spout end and tighten.
ROUGH-IN

4
www.homewerksww.com
LIMITED LIFETIME WARRANTY
The distributor warrants to the original consumer purchaser this product to be free
from defects in material and workmanship under normal use in residential applications.
At its option, the Company will provide repair parts or replace defective product
when the product is used in accordance with the manufacturer’s specications.
The distributor provides a limited 5-year warranty on the nish of this product to the
original purchaser. At its option, the distributor will provide repair parts or replace
defective product when the product is used in accordance with the manufacturer’s
specications. Use of mild abrasive, abrasive or chemical cleaners may damage the
nish of the faucet. We recommend cleaning your faucet with a soft cloth, moistened
with water. Damage resulting from the use of abrasive or chemical cleaners SHALL
VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where damage
is caused by use of non-genuine parts; is due to installation error, product misuse,
negligence or faulty maintenance; or where the product is not installed according to
local building codes.
This warranty excludes labor charges or damage incurred during installation, repair
or replacement, and any indirect, incidental or consequential damages, losses, injury
or costs of any nature. This warranty is in lieu of and excludes all other warranties,
conditions and guarantees, whether expressed or implied, including without restriction
those of merchantability or tness of use.
Liability under this warranty will not exceed the purchase price for the product claimed
to be defective by the original consumer purchaser. Some states or provinces do not
allow the exclusion or limitation of consequential damages so the above limitations
or exclusions may not apply. This warranty gives you specic legal rights and you
may also have other rights which vary from state to state, or province to province.
Inquiries regarding warranty claims can be directed to 1-877-319-3757,
8 a.m. - 5 p.m., CST, Monday - Friday.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-877-319-3757, 8 a.m. - 5 p.m., CST, Monday - Friday.
PART DESCRIPTION PART #
1Hose adapter assembly RP30024
2Aerator assembly RP30021CH
3Spout nut RP56034CH
4Washer RP64085
5O-ring RP60008
6Spout ring/clip RP70106
7Index button - Hot RP10020
8Index button - Cold RP10021
9Handle with screw RP13071CH
10 Bonnet RP70001
11 Cartridge RP22001
12 Seat and springs RP22008
13 Washer spacer RP64016
14 Escutcheon RP80097
15 Base plate RP80113
16 Mounting nuts RP56001
1
2
713
9
8
3
4
5
6
10
14
15
16
11
12