Honeywell VOYAGER 1202G BF User manual

Voyager™ 1202g BF
Cordless Single-Line Laser Bar Code Scanner and
CCB00-010BT-01N-BF base
Quick Start Guide
VG1202BF-QS Rev B
2/15
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
Pro češtinu jdi na www.honeywellaidc.com.
Pre slovenčinu choďna www.honeywellaidc.com.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
한글 www.honeywellaidc.com 로이동합니다 .

Note: Refer to your user’s guide for information about cleaning your
device.
Getting Started
Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. When the
base is connected and powered up, put the scanner in the base to
establish a link. The green LED on the base flashes to indicate the
scanner’s instant charge pack is charging. The scanner must be
returned to the base when not in use. A scanner charged on the base
with the power supply for 35 seconds will result in 100 scans, with
one scan every second.
Power Supply Assembly (if included)

USB Connection
Note: Charging the scanner through a USB port takes more time
than direct AC adapter charging.

RS232 Serial Port Connection

RS485 Connection

Keyboard Wedge Connection
Note: For Keyboard Wedge, you must use the power supply.

Base LED Sequences and Meaning
Red LED - Host Communication
Red LED Condition
Off Power off, USB suspend
On continuously Power on, system idle
Short blinks. Occurs while
transferring data to the host port.
Receiving data
Green LED - Scanner Battery
Green LED Condition
Off Instant charge pack not detected or
charge suspended
Slow flash, 1 second on, 1 second
off
Charging, Instant charge pack near
empty
Slow flash, 0.5 second on, 0.5
second off
Charging, Instant charge pack at
medium capacity
Slow flash, 0.25 second on, 0.25
second off
Charging, Instant charge pack near
full capacity
On continuously Charge complete
Scanner
Charge Base
Base LEDs

Reading Techniques
Standard Product Defaults
The following bar code resets all standard product default settings.
RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to program
the terminal, then power cycle the cash register.
Note: For additional RS485 interface selections, see the User’s
Guide for your product at our website,
www.honeywellaidc.com.
Standard Product Defaults
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface

Keyboard Country
If your interface is USB Keyboard or Keyboard Wedge, your
keyboard layout default is a US keyboard. To change this layout,
refer to the chart below for your keyboard country. Scan the
Program Keyboard Country bar code below, then scan the numeric
bar code(s) for the appropriate Country Code from page 2, then scan
the Save bar code.
By default, national character replacements are used for the
following characters: #$@[\]^‘{|}~ Refer to the ISO 646 Character
Replacements chart in your User’s Guide to view the character
replacements for each country.
Country
Code Scan
Country
Code Scan
Country
Code Scan
Arabia 91 IBM Financial 90 Sweden/
Finland 2
Belgium 1Italy 5Switzerland 6
China 92 Japan 28 Thai 94
France 3Korea 93 Turkey (Q) 24
Germany/
Austria 4Portugal 13 USA (Default) 0
Great Britain 7Russia 26 Vietnam 95
Hungary 19 Spain 10
Program Keyboard Country
Save

Locked Link
If you link a scanner to a base using the Locked Link Mode, other
scanners are blocked from being linked if they are inadvertently
placed into the base. If you do place a different scanner into the
base, it will charge the scanner, but the scanner will not be linked.
To use a different scanner, you need to unlink the original scanner by
scanning the Unlink Scanner bar code, below.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will be
overridden; the broken or lost scanner’s link with the base will be
removed, and the new scanner will be linked.
Unlinking the Scanner
If the base has a scanner linked to it, that scanner must be unlinked
before a new scanner can be linked. Once the previous scanner is
unlinked, it will no longer communicate with the base. Scan the
Unlink Scanner bar code to unlink a scanner.
Locked Link Mode
(Single Scanner)
Override Locked Scanner
Unlink Scanner