Honeywell HCC-745NTW/PTW User manual

-1 -
OPERATION MANUAL
READ AND KEEP THIS OPERATION MANUAL
Day and Night / WDR
OSD COLOR CAMERA
HCC-745NTW/PTW
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance(servicing) instructions in the literature
accompanying the appliance.

-2 -
Warning:
This equipment generates and uses radio frequency energy
and if not installed and used properly, I.e., in strict accordance
with the instruction manual, may cause harmful interference
to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to Subpart
J of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
Warning:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
PREFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Indicate a potentially hazardous situation which if not avoided,
may result in minor or moderate injury. It may also be used to
alert against unsafe practices.

-3 -
CAUTION FOR SAFE OPERATION
1. Water and Moisture
To prevent fire or shock hazard, do not expose this camera
to rain or moisture.
2. Servicing
Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.
3. Power Sources
To prevent electric shocks and risk of hazards, do NOT use
more than the specified power source.
4. Environment
Do not install too warm or too cold place. Recommended
operation temperature is between -5℃and 60℃
5. Sunlight
Do not point the camera at the sun. CCD can be damaged.
6. Heavy Shock and Vibration
Do not drop the camera or subject it to heavy shock of
vibration.
7. Install on an Unstable Place
Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance.
8. When operation is incorrect or a malfunction is observed
While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.
9. Cleaning
Turn the power off and wipe off the dirt with a dry soft
cloth. If it is extremely dirty, use furniture cleaner to wipe it
off. To clean the lens, use a blower or lens cleaning
tissue. (available from any camera dealer)
10. Do not shoot any source of bright light.
If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid
- state pickups, and is not a malfunction.
11. Damage Requiring service
Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:
a. If the power-supply cord or plug is damaged.
b. If the camera has been exposed to rain or water.
c. If liquid has been spilled, or objects have fallen into the camera.
d. If the camera does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the camera to its normal operation.
e. If the camera has been dropped or the cabinet has been damaged.
f . If the camera exhibits a distinct change in performance.
Warranty is not covered in case of natural disaster or wrong
Installation.

-4 -
CONTENTS
Thank you for using this OSD Color Camera with Day and Night, WDR. To
get the best efficiency, read carefully all instructions in this manual before
use, and keep this manual for reference. If you have any problems with
this camera, contact your supplier to service.
----------------------- 5
----------------------- 6
----------------------- 8
----------------------- 10
----------------------- 11
----------------------- 19
----------------------- 20
1. Features
2. Names & Functions
3. Installation
4. Remote Control Connections
5. On Screen Display
6. Specifications
7. Dimensions

-5 -
1. Features
Honeywell’s HCC-745NTW/PTW Series is a high sensitivity CCD color camera with high
sensitivity function
of Day & Night function and field integration technique.
▣1/3” Double Scan Color CCD ( NTSC: 410,000 / PAL: 470,000 )
▣Outstanding BLC implementation with WDR(Wide Dynamic Range) function.
( 3 steps available : OFF / BLC / WDR )
▣Adapted CS/C mount lens adjustable.
▣Excellent signal-to-noise ratio of more than 50dB.
▣High Sensitivity : Minimum illumination of 0.001lx @ F1.2, 50IRE, DSS On X510, Night mode
▣2-WAY Auto Iris : Video iris or DC iris lens can be used.
▣2-WAY Auto Iris : Video iris or DC iris lens can be used.
▣OSD Control :
Flickerless, AGC, Manual shutter control, Maximum Fields Select,
WDR, BLC, Title and Camera ID setting, Sync Mode
▣External synchronization with LINE LOCK(L/L) and Auto Detection.
▣Auto White Balance : Auto white balance realizes true color reproduction within various
light sources.
▣Remote Control through RS485 / RS232C
-. Camera ID : 0 ~ 255
-. Title : 10 characters
-. Camera ID & Title Display Position : Bottom Right, Bottom Left, Top Right, Top Left, No Display
-. AWB Mode : ATW, AWC, INDOOR, USER FIX, OUTDOOR, Fluorescent, MWB
-. BLC Mode : OFF, ON
-. WDR Mode : OFF, ON
-. ELC / ALC Mode : ELC (AUTO/Manual), ALC (VSD Lens/DC Lens)
-. Max Fields Control : x2 ~ x510
-. Sync. Control : AUTO, Internal, L/L (V.PH control)
-. Shutter Speed Control : 8 steps including Flickerless
-. Max AGC Control : OFF ~ 38dB

-6 -
LENS CONNECTOR
Connect Auto Iris Lens
plug
Set Screw
Loosen Locking Ring to adjust mounting
ring
C/CS Mount Adaptor
• C-Mount lens : Turn Counterclockwise
• CS-Mount lens : Turn Clockwise
2. Names & Functions

-7 -
(+) BUTTON
(DOWN) BUTTON
(UP) BUTTON
(-) BUTTON
MENU BUTTON
POWER INPUT
TERMINAL
CAMERA CONTROL CONNECTOR
( Refer to 4. Camera Control Methods )
Lens Type Select Switch
DC Lens : with no iris amp.
VSD Lens : with iris amp.
POWER ON LAMP
In power ON state,
this LED is ON .
VIDEO OUTPUT
This is the output terminal
for composite video signal

-8 -
3.2 Mounting a Lens
3.2.1 C/CS Mount Lens
①Remove the protective cap in front of the camera.
②Adjust the mount ring whether it is for C or CS.
③Loosen Set Screw.
④Turn the mount ring counterclockwise in case of C-Mount Lens.
Turn the mount ring clockwise in case of CS-Mount Lens
3.2.2 Auto Iris Lens
①Remove the cover of the auto iris lens plug and connect with the lens cable.
②Connect the auto iris lens plug to the 4-pin lens terminal on the side of
the camera.
③Set the EE MODE to ALC MODE on the OSD menu ( see 5.6 AE MODE)
-. Auto iris lens with no amplifier : Set the DC LENS on the OSD menu
-. Auto iris lens with amplifier : Set the VSD LENS on OSD menu
☞Adjust by using “LENS ADJ.” on OSD menu to avoid hunting.
3. Installation
3.1 The packing box should include, in addition to this User Guide:
-. One HCC-745NTW or HCC-745PTW camera
-. One 6-pin connection cable ( G-113510-200 )
-. One Auto Iris lens plug
VSD LENS PIN CONFIGURATION
12
34①③
④②
1. POWER(12V) 2. NO CONNECTION
3. VIDEO SIGNAL 4. GND
Set the select switch to VSD
DC IRIS LENS PIN CONFIGURATION
12
34①③
④②
1. CONTROL- 2. CONTROL+
3. DRIVE+ 4. DRIVE-
Set the select switch to DC

-9 -
④Set the switch on the rear of the camera to DC or VSD.
☞Use the connection recommended by the manufacturer.
(E4-191, Chuo Musen, Japan) For best practices, read the lens manual
carefully. You may need to set the flange back focus.
3.3 Flange back focus adjustment
3.3.1 Fixed Lens
a. Loosen the setscrew and set the lens focus ring to infinity ( ∞).
b. Turn the back focus adjustment ring until you see a clear image (the distance
from the camera to the object is more than 23m).
c. Tighten the setscrew.
3.3.2 Zoom lens
a. Loosen the setscrew and set the lens to the maximum telephoto position.
b. Turn the back focus adjustment ring to adjust the focus.
c. Auto iris lens: Aim the camera at a comparatively dark object or reduce
the ambient light so that the iris is fully open.
d. Set the lens to its maximum wide angle position, then set the focus.
e. Repeat step b, c and d until the difference between the focusing positions
is as small as possible.
f. Tighten the setscrew when the best focusing point is found.
3.4 Connection of POWER supply
☞Check the power source from the external power supply before power on.
☞Power source capacity :
AC 24V, more than 500mA (Recommended Honeywell HAC-2450)
DC 12V, more than 500mA (Recommended Honeywell HDC-1260R)

-10 -
4.1 RS-232C connection ( HCC-745NTW/PTW )
4. Remote Control Connections
Connect to Serial PORT 6P Cable
2
3
4
RD ( TxD )
TD ( RxD )
GND
6P Cable
Serial Cable
Serial Cable
( 9 Pin D-Sub )
2
RD
3
TD
5
SG
4
6
7
8
Connect internally
for communication
4.2 RS-485 connection ( HCC-745NTW/PTW-VR )
Connect to Serial PORT 6P Cable
Serial Cable
RS485 Converter
3
2
TRx +
TRx-
6P Cable
RS485 Converter
TRx+
TRx-
RS485
RS232C
1. Red : Not Use
2. Blue : RD(TxD)
3. Yellow : TD(RxD)
4. Black : GND
5. Red : Not Use
6. Black : Not Use
1. Red : Not Use
2. Blue : TRx-
3. Yellow : TRx+
4. Black : Not Use
5. Red : Not Use
6. Black : Not Use

-11 -
5. On Screen Display
<Fig5-1. OSD Information Display>
5.1 Understanding the On-Screen Display
a. Press MENU briefly to confirm the current operation setup.
The information (see Fig 5-1) will disappear after five seconds
if there is no button action.
b. When it zoom in or out pressing UP or DOWN key,
whole OSD Information will appear and then disappear.
Press (+) , (-) button, only upper part of OSD Information
( for displaying camera mode ) will appear and then disappear.
(It is for checking current whole camera mode and zoom position )
c. Even though the OSD message disappears the Camera ID
or Title will continue to display. If you do not wish to display the ID,
you can change the display position. (see 5.11)
Options are: Bottom Right, Top Left, Top Right, Non display.
* If you do not need to display the Operating OSD (for example,
for an external text overlay board), it can be set to OFF at all times
through a remote control using RS232C or RS485 connection.
<Table5-1. Operating OSD description>
④ ⑥
①
②, ③ ②, ③
②, ③
⑤
Manual modeMWB
WB MODE
Zoom WIDEDx1.0 << WIDE
Zoom TELEDx2.5 >>TELEZOOM
DISPLAY
①
Fluorescent (4200°K)FRS
User modeUSR
One Push modeAWC
1/500001/50000
1/10000
1/10000
1/40001/4000
1/20001/2000
1/10001/1000
1/5001/500
1/2501/250
Outdoor preset (5400°K)OUT
NTSC:1/120, PAL:1/100FL
Auto Trace White BalanceATW
⑥
Indoor Preset (3200°K)IN
DESCRIPTIONOSD FormatFUNCTION
NTSC:1/60, PAL :1/501/60 (1/50)Shutter
Speed
⑤
Back Light ONBL
Back Light OFFNon displayBack Light
④
See 5.11■■…■■TITLE
③
ID : 0None displayCAMERA ID
②
ID : 1 ~ 255ID : 002
1/20000 1/20000

-12 -
5.2 Display SETUPMENU
a. Press and hold the MENU (center) button for 2 seconds to display the Setup
menu.
b. Press the UP or DOWN buttons to select a menu item.
5.3 Move from SETUPMENU to submenu
a. Press the MENU button to enter the selected submenu.
b. Press the + or – buttons to increase/decrease the value of the selected item.
5.4 Saving your Settings
When you are satisfied with your settings:
a. Press MENU for two seconds. The submenu is replaced by one of two messages:
①“QUIT?” : displays when you have not changed any settings.
Selecting QUIT exits OSD menu without saving any changed values.
②“SAVE?” : displays when values have been changed.
Selecting SAVE exits OSD menu and saves your changes.
b. Press + or – to select SAVE or QUIT and press MENU to exit OSD. Press UP or
DOWN buttons to cancel the SAVE/QUIT and return to the OSD.
5.5 General Setting
①SYNC. Level
: Adjust the proper SYNC. Level from 0~15.
SYNC. LEVEL 0 →1 →…→15
②BURST Level
: Adjust the proper BURST Level from 0~255.
BURST LEVEL 0 →1 →…→255
③SYNC. Mode
: To synchronize the vertical interval sync pulse of your camera with other
equipment to reduce the effect of picture roll on the monitor.
SYNC. MODE AUTO →INTERNAL →L/L
④Vertical Phase
: Adjust the proper phase in L/L.
V. PHASE 0 →1 →…→524
☞
Notice
L/L mode is not available in DC 12V power.
<Fig5-2. SETUP MENU change>
<< SETUP MENU >>
GENERAL SETTING
AE MODE
WB MODE
NIGHTSHOT MODE
BLC/WDR MODE
PZM SETTING
CAMERA ID SETTING
SPECIAL FUNCTION
FACTORY DEFAULT
EXIT MENU
<<GENERAL SETTING>>
SYNC. LEVEL
BURST LEVEL
SYNC. MODE
RETURN
0
98
AUTO
L/L
<<GENERAL SETTING >>
①SYNC. LEVEL
②BURST LEVEL
③SYNC. MODE
④V. PHASE
RETURN
<Fig5-3. General Setting >
0
98
L/L
000

-13 -
5.6 AE mode
①MODE
: ELC – for a manual (fixed) lens.
ALC – for an automatic iris lens.
MODE ELC →ALC
②CONTROL
CONTROL AUTO
♦ELC MODE
-. AUTO : Iris operates elctronic exposure automatically.
-. MANUAL : Adjust the iris by changing the high shutter speed
or AGC manually.
♦ALC MODE
-. VSD LENS : Select for video-type lens
-. DC LENS : Select for direct drive-type lens.
③MANUAL SHUTTER
: Adjust brightness with high shutter speed.
This field is not adjustable when the camera is set to ELC MODE, Auto.
MAN. SHUTTER 1/60 →1/100 →. . →1/50000
④MANUAL AGC
: Adjust AGC gain at ELC MODE, Manual.
MAN. AGC OFF →10dB →. . . →34dB
☞
Notice
Accoring to mode, some menu will skip, not to adjust.
<Fig5-5. Setting Camera Linghting>
<< AE MODE >>
①MODE
②CONTROL
③MAN. SHUTTER
④MAN. AGC
⑤LENS ADJ.
⑥BRIGHTNESS
⑦MAX GAIN
⑧MAX FIELDS
RETURN
ELC
AUTO
1/60
OFF
Done
60
34dB
510FLDS
⑤LENS ADJUSTMENT
: Adjust level for DC / VSD lens. While it is adjusting, it displays “Adj-ing”,
after it is completed, it displays “Done”.
LENS ADJ. Adj-ing →Done
☞
Notice
For the better adjustment, set LEVEL on VSD lens to middle value.
⑥BRIGHTNESS
: Adjust level of Auto Iris. The smaller brightness value is, the darker it is,
because iris is closed more. On the contrary the bigger brightness value
is, the brighter it is, because iris is opened more.
BRIGHTNESS 0 ~ 99
⑦MAX AGC
: Adjust maximum value of AGC gain.
MAX GAIN OFF →8dB →. . . . →38dB
⑧MAX FIELDS
: Compensate for low illumination. Adjust the maximum integration
fields to get a brighter dynamic image. The scene will be slower
than when set to OFF. The larger this field, the greater the noise
of the image. For more dynamic range, adjust the MAX FIELD and
increase the MAX AGC. .
MAX FLDS OFF →2FLDS →3FLDS →4FLDS →. . . .
→18FLDS →19FLDS →20FLDS →40FLDS
→80FLDS →160FLDS→320FLDS -> 510FLDS

-14 -
5.7 White Balance Mode
①MODE
: To set how the camera tracks to accept different lighting conditions
within the color range of 2,500°K ~ 8,000°K.
ATW (Auto Trace White Balance Mode)
: Feedback system that automatically aligns the white balance
(2,500°K ~ 8,000°K).
IN (Indoor)
: General indoor scenes preset (3200°K)
OUT (Outdoor)
: Preset for outside environments and high contrast scenes where the
camera is focused on the darker (5400°K)
MANUAL
: RED GAIN, BLUE GAIN are changed depending Black Body
AWC (Auto/PushAuto)
: Performs faster action than ATW mode without an operating range
FLUORES. (Fluorescent)
: Office environments with fluorescent or tungsten lighting. Provides
lowest dynamic range of all presets (4200°K)
USER
: RED GAIN, BLUE GAIN are adjustable (0 ~ 255)
<Fig5-6. White Balance Control>
<< WB MODE >>
①MODE
②CONTROL
③RED GAIN
④BLUE GAIN
RETURN
USER
R/B CONT
1
2
②CONTROL
ATW AUTO
IN 3200°K
OUT 5400°K
MANUAL R<-->B
AWC LOCK →PUSH
AWC AUTO
FLUORES. 4200°K
USER R/B CONT
1. MANUAL : Press + or – button to adjust RED GAIN, BLUE
GAIN automatically to fit Black Body.
2. PUSH : Press + or – button to start the AWC operation.
LoCK : Release the key to fit the present shooting scene’s
white balance
③RED GAIN (USER mode)
RED GAIN 0 →1 →…. →254 →255
④BLUE GAIN (USER mode)
BLUE GAIN 0 →1 →…. →254 →255

-15 -
<Fig5-7. NIGHTSHOT Control>
<< NIGHTSHOT MODE >>
①MODE
②DETECT TIME
③D→N LEVEL
④N→D LEVEL
⑤NIGHT COLOR
RETURN
AUTO
3sec.
3
7
B/W
5.8 NIGHTSHOT MODE
①MODE
: The Nightshot menu allows you to set how the camera reacts to
changes in low light illumination and to set when the camera switches
between Night and Day modes.
AUTO – The camera removes or inserts IR cut filter by auto detecting
luminance.
ON – IR cut filter is removed (Night mode)
OFF – IR cut filter is inserted (Day mode)
MODE OFF →AUTO →ON →….
②DETECT TIME
: Sets the time – 1 to 10 seconds – before the camera switches to Day
or Night mode after detecting a low light condition.
DETECT TIME 1 sec. →2 sec. →…. →10 sec.
③DAY to NIGHT threshold
: Determines the low light detection level – 1 to 10 – when the camera
switchs to Night mode. The lower the value, the darker the lighting
conditions befroe the camera switches.
D→N LEVEL 1 →2 →3 →…. →15
④NIGHT to DAY threshold
: Determines the low light detection level – 1 to 10 – when the camera
switches to Day mode. The higher the value, the brighter the lighting
conditions before the camera switches.
N→D LEVEL 15 →9 →8 →…. →1
☞
Notice
MODE must be set to AUTO. D->N LEVEL must be set at least 2 less than
the N->D LEVEL setting.
<Fig5-8. BLC/WDR MODE >
<< BLC/WDR MODE >>
①MODE
②LEVEL
RETURN
WDR
8
5.9 BLC/WDR MODE
①MODE
: Prevents the object in the center of the image from darkening
(silhouette effect) when there is excessive light from behind.
MODE OFF →BLC →WDR →….
WDR [Wide Dynamic Range] is one of Backlight Compensation,
you can watch not only the object in the center but also the objects
around clearly.
②LEVEL
: Adjust the proper level for WDR.
LEVEL 0 →1 →2 →…. →15
☞
Notice
If you set WDR ON, you will not be able to digital zoom in or out.
⑤NIGHT COLOR
: Set the color mode as B/W (monochrome) or COLOR in Night mode.
NIGHT COLOR B/W →COLOR →….
☞
Notice
MODE must be set to AUTO or ON.

-16 -
5.10 PRIVACY ZONE
①ZONE
:PZM(Privacy Zone Mask) is to hide the unwanted view to protect
privacy invasion. It works with Zoom/PAN/TILT operation. Select PZM
zone upto 8 zones.
ZONE NUM. ZONE 1 →ZONE 1 →…. →ZONE 8
②CONTROL
: Set ON/OFF for each PZM Zone.
CONTROL OFF →ON →….
Press and hold the MENU (cernter) button for 2 seconds to display
PZM move menu. Move PZM to appropriate position by using
UP/DOWN/-/+ button. Press and hold the MENU button for 2 seconds
again to return previous menu.
<Fig5-10. Privacy Zone Masking>
<< PRIVACY ZONE >>
①ZONE NUM.
②CONTROL
③H START
④H END
⑤V START
⑥V END
⑦PZM MASKING
RETURN
PRESS MENU TO MOVE
ZONE 1
ON
200
300
50
100
BLACK
<Fig5-9. PZM move>
③Horizontal Start position
H START 200
④Horizontal End position
H END 300
⑤Vertical Start position
V START 50
⑥Vertical End position
V END 100
⑦MASKING COLOR
: Choose the color to mask the PZM zone. 10 color (Black,Gray,
Light Gray,White,Red,Blue,Green,Yellow, Cyan, Magenta).
PZM MASKING BLACK →D.GRAY →.. →MAGENTA
UP:↑,DOWN:↓,-:←,+:→
RETURN:MENU

-17 -
④Title
: It is the name of Camera. It enters 10 characters including blank..
TITLE: ■■■■■■■■■■
<Fig 5-11. CAMERA ID SET >
5.11 Camera ID SET
①ID SET
: Camera ID is indicating number assigned each Camera in case of
controlling many Cameras. It is from 0 to 255. But in case of 0, that is
not displayed on screen. It is always displayed even though whole Operating
OSD is disappeared on the screen. But it is possible to make non display
and to choose display position (BOTTOM RIGHT, TOP RIGHT, TOP
LEFT) by RS-232C communication.
CAMERA ID 0 ~ 255
☞
caution
1. In case of Camera ID FIX model, it cannot be selected..
2. ID is not changed by MENU control through communication.
②DISPLAY MODE
: Choose which is to display Camera ID or Title.
DISPLAY CAM ID →TITLE →….
③DISPLAY POSITION
: Choose where is to display Camera ID or Title on Right Bottom, Left Top,
Right Top or not to display.
POSITION R.BOT →L.TOP →R.TOP →NONE
Let’s enter the Title as “R1” , example
-. Select the position of title character by using (+) or (-) key.
The chosen position is blinking.
TITLE: □■■■■■■■■■
-. Select the character “R” among
ⓑ ~ ⓕ by using UP,DOWN,
(+),(-) key. The chosen character “R” is blinking.
-. Press MENU key, the character “R” is entered in the Title.
TITLE: R■■■■■■■■■
-. Select the next position of title character by using (+) or (-) key.
The chosen position is blinking.
TITLE: R□■■■■■■■■
-. Select the character “7” among
ⓑ ~ ⓕ by using UP,DOWN,
(+),(-) key. The chosen character “7” is blinking.
-. Press MENU key, the character “7” is entered in the Title.
TITLE: R7■■■■■■■■
▣How to Enter the Title ▣
7
N
e
8
P
f
9
Q
g
A
R
h
E
V
l
B
S
i
C
T
j
D
U
k
F
W
m
7
N
e
8
P
f
9
Q
g
A
R
h
E
V
l
B
S
i
C
T
j
D
U
k
F
W
m
<< CAMERA ID SETTING >>
①CAMERA ID
②DISPLAY
③POSITION
ⓐABCDEFGHIJKLMNOPQRST
ⓑUVWXYZabcdefghijklmn
ⓒopqrstuvwxyz12345678
ⓓ9!?#$%&<>*,.:;/+-=~■
④TITLE : HONEYWELL
RETURN
000
TITLE
R.BOT

-18 -
<Fig5-12. SPECIAL FUNCTION >
<< SPECIAL FUNCTION >>
①MIRROR
②SHARPNESS
③NEGATIVE
④FREEZE
⑤BAUDRATE
⑥PROTOCOL
⑦F.OSD DISP
RETURN
OFF
10
OFF
OFF
9600bps
DEFAULT
ALL
5.12 SPECIAL FUNCTION
①Mirror Mode
: Mode ON is Mirror Mode, OFF is general screen state.
MIRROR OFF →H MIRROR →V MIRROR →FLIP . . . .
②Sharpness
: Use to change the contour of Scene.
SHARPNESS 0 ~ 15
③Negative Mode
: Use for Positive and Negative mode. ON is Negative mode,
OFF is Positive mode namely general screen state.
NEGATIVE OFF →ON →….
④Freeze Mode
: It pause current image. ON is to stop, OFF is to return
to normal state.
FREEZE ON →OFF →….
☞caution
1. Freeze image is not saved after Power OFF / ON .
That’s why it doesn’t have memory for saving.
⑤BAUD RATE
: Use to communicate through RS232C, RS485, RS232TTL .
BAUDRATE 4800bps →9600bps →…. →312kbps
☞caution
1. When Baud Rate of Camera and external system is not
same, it happens Communication fail.
⑥PROTOCOL
: Use to communicate through RS232C, RS485.
PROTOCOL DEFAULT →VCL →KD6 →P/D →....
⑦Function OSD Display
OSD DISP ALL →NONE →TOP →BOTTOM →....
ALL : Whole Function OSD display
( Focus Mode, Key state, Zoom Ratio, ID )
TOP : Only Upper OSD display ( Focus Mode, key state )
BOTTOM : Only Lower OSD display ( Zoom Ratio, ID )
NONE : Whoe Function OSD display not.
5.13 FACTORY DEFAULT
: All changed data are returned to shipping condition.
For Initialization, select “RESTORE FACTORY SETTING” and
push MENU key.
☞caution
1. Keep in mind that this mode return all changed data to
shipping condition.
2. Some menu as ID,TITLE, etc are not initialized.
<Fig5-13. RESTORE DEFAULT>
<< RESTORE DEFAULT >>
①RESTORE FACTORY SETTING
RETURN
<Fig5-14. EXIT MENU>
<< EXIT MENU >>
①SAVE AND EXIT
②EXIT
RETURN
5.14 EXIT MENU
①SAVE AND EXIT
: Exit OSD MENU with saving all changed data.
②EXIT
: Exit OSD MENU withoout saving all changed data.

-19 -
6. Specifications
Model Name HCC-745NTW HCC-745PTW
Pick-up Device 1/3” Sony Double Scan Color CCD
Total/Effective Pixels 410,000 / 380,000 470,000/440,000
Scanning System 525 lines, 2:1 Interlace
Digital Zoom Ratio X1.0 ~ x2.5 can be adjustable
Sync System Internal / External (L/L ), Auto detecting selectable
H.Resolution 480 TV lines 470 TV lines
S/N Ratio more than 50 dB ( AGC OFF )
Min. illuminance 0.2lx @50IRE, AGC 38dB, Night OFF;
0.01lx @50IRE, AGC 38dB, Night OFF, DSS 510fields;
0.01lx @50IRE, AGC 38dB, Night ON;
0.001lx @50IRE, AGC 38dB, Night ON, DSS 510fields;
Brightness 0 ~ 99 adjustable
Shutter Speed 1/60 ~ 1/10,000 1/50 ~ 1/10,000
Field Integration x2 ~ x510 adjustable
Mirror Horizontal / Vertical / Filp (Horizontal + Vertical)
Day & Night Mode ON / OFF / AUTO
Remote Control RS-232C (basic) / RS-485 (option)
BLC / WDR BLC : ON / OFF, WDR : ON / OFF
Power Supply/Consump. DC12V ±2V,AC24V ±10% (5.0 W)
Privacy Zone ON ( up to 8 Zones ) / OFF
AGC ON ( 8 ~ 38dB ) / OFF
White Balance ATW / AWC / OnePush / Indoor / Outdoor / MWB / User / Fluorescent
Operation/Storage Temp. -10 ~ 60 ℃( Recommended -5 ~ 50 ℃) / -20 ~ 60 ℃
Dimension / Weight 68 x 56 x 120 (mm) / less than 410g

-20 -
7. Dimension