Honeywell PERFORMANCE LITE 2MP SD User manual

PERFORMANCE
LITE
2MP SD
CAMERA
HIE2PI-S | HIB2PI-S | HIE2PIV-S | HIB2PIV-S
User
Manual

Notes on Safety
• Please use the specified power supply to connect.
• Do not attempt to disassemble the camera; in order to prevent electric shock, do not remove screws
or covers.
• There are no user-serviceable parts inside. Please contact the nearest service centre as soon as
possible if there is any failure.
• Avoid from incorrect operation, shock vibration, heavy pressing which can cause damage to
product.
• Do not use corrosive detergent to clean main body of the camera. If necessary, use a soft dry cloth
to wipe dirt. For hard contamination, use neutral detergent. Any cleanser for high grade furniture
is applicable.
• Avoid aiming the camera directly towards extremely bright objects, such as the sun, that may
damage the image sensor.
• Please follow the instructions to install the camera. Do not reverse the camera, or else reverse
image will be received.
• Do not operate when temperature, relative humidity and power supply are beyond the limited
stipulations.
• Keep away from heat sources such as radiators, heat registers, stove, etc.
• Do not expose the product to the direct airflow from an air conditioner.
• This a product instruction manual not quality warranty. We may reserve the rights of amending
the typographical errors, inconsistencies with the latest version, software upgrades and product
improvements, interpretation and modification. These changes will be published in the latest
version without special notification.
• When this product is in use, the relevant contents of Microsoft, Apple and Google will be involved
in. The pictures and screenshots in this manual are only used to explain the usage of our product.
The ownerships of trademarks, logos and other intellectual properties related to Microsoft, Apple
and Google belong to the above-mentioned companies.
• This manual is suitable for IR water-proof network camera. All pictures and examples used in the
manual are for reference only.

Disclaimer
With regard to the product with internet access, the use
of product shall be wholly at your own risks. Our company
shall be not responsible for abnormal operation, privacy
leakage or other damages resulting from cyber attack,
hacker attack, virus inspection, or other internet security
risks; however, our company will provide timely technical
support if necessary.
Surveillance laws vary from country to country. Check
all laws in your local region before using this product for
surveillance purposes. We shall not take the responsibility
for any consequences resulting from illegal operations.
BIS Marking
The products have been manufactured to comply with the
BIS directives.
Disclaimer & Regulatory
Information

Table of Contents
Introduction 1
Network Connection 2
LAN 2
Access through IP-Tool 2
Directly Access through IE 4
WAN 6
Access through the router
or virtual server 6
Access through static IP 7
Live View 8
Configuration 9
System Configuration 9
Basic Information 9
Date & Time 9
Local Configuration 10
Storage 10
Weekly schedule 11
Day schedule 11
Image Configuration 12
Display Configuration 12
Video Stream 13
OSD Configuration 14
Video Mask 15
ROI Configuration 16
Alarm Configuration 17
Motion Detection 17
Other Alarms 18
Alarm Server 19
Network Configuration 19
TCP/IP 19
Port 20
Server Configuration 21
DDNS Configuration 21
802.1x 23
RTSP 24
UPNP 25
Mail configuration 25
HTTPS 26
QoS 27
Security Configuration 28
User Configuration 28
Online Video User 29
Block and Allow List 29
Security Management 30
Maintenance Configuration 30
Backup and Restore 30
Reboot 31
Upgrade 31
Operation Log 32
Search 33
Image Search 33
Video Search 34
Local Video Search 34
SD Card Video Search 35
Appendix 1 Q & A 37

1
Introduction
This Performance Lite SD 2MP IP cameras (short for IP-CAM) is designed for high performance CCTV solutions. It adopts
state of the art video processing chips, integrated with the most advanced technologies (like video encoding and decoding
technology) to make the image transmission more stable and smooth. Moreover, the built-in WEB server of this series improves
the performance of the traditional surveillance system so that users can be easy to operate and monitor.
This product is widely used in banks, telecommunication systems, electricity power departments, law systems, factories,
storehouses, uptowns, etc. In addition, it is also an ideal choice for surveillance sites with middle or high risks.
Main Features
• ICR auto switch, true day/night
• 3D DNR, digital WDR
• ROI coding
• Support smart phone, iPad, remote monitoring
or
IPC Network Computer
or
NVR
IPC Network Hybrid DVR Moniter
or
IPC Network CMS/NVMS
Performance Lite 2MP SD Camera - User Manual | Introduction

2
Network Connection
or
Network Cable
IPC Network
Switch
Computer
Network Cable
Connect IP-Cam via LAN or WAN. Here only take IE browser for example. The details are as follows:
LAN
In LAN, there are two ways to access IP-Cam: 1. Access through IP-Tool; 2. Directly access through IE browser.
Access through IP-Tool
Network connection:
1. Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the PC from the CD.
2. Double click on the IP-Tool icon on the desktop to run this software as shown below:
Performance Lite 2MP SD Camera - User Manual | Network Connection

3
3. Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the information of the camera listed
in the above table to show the network information on the right hand. Modify the IP address and gateway of the camera and
make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your
device according to the practical situation.
For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be changed to 192.168.1.X.
After modification, please enter the password of the administrator and click on the “Modify” button to modify the setting.
The default password of the administrator is “123456”.
The default password of the administrator is “123456”.
4. Double click on the IP address and then the system will pop up the IE browser to connect IP-CAM. Then follow directions to
install and run the applicable plug-in.
Enter the username and password to log in.
The system will pop up the above-mentioned textbox to ask you to change the default password. It is strongly recommended to
change the default password for account security. If “Do not show again” is checked, the textbox will not appear next time.
Performance Lite 2MP SD Camera - User Manual | Network Connection

4
or
IPC Computer
Network Cable
Directly Access through IE
The default network settings are as shown below:
IP Address: 192.168.226.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.226.1
HTTP: 80
Data Port: 9008
Use the above default settings when logging in the camera for the first time. Directly connect the camera to the computer
through network cable.
1. Manually set the IP address of the PC and the network segment should be same as the default settings of the IP camera.
Open the network and share centre. Click “Local Area Connection” to pop up the following window.
Select “Properties” and then select internet protocol according to the actual situation (for example: IPv4). Next, click “Properties”
button to set the network of the PC.
Performance Lite 2MP SD Camera - User Manual | Network Connection

5
2. Open the IE browser and enter the default address of IP-CAM and confirm.
3. Follow directions to download and install the Active X control.
4. Enter the default username and password in the login window and then enter to view.
Performance Lite 2MP SD Camera - User Manual | Network Connection

6
1. Make sure the camera is connected to the local network and then log in the camera via LAN and go to Config > Network > Port
menu to set the port number
WAN
Access through the router or virtual server
2. Go to Config > Network > TCP/IPv4 menu to modify the IP address.
or
IPC Router Computer
Network
Cable
Network
Cable
Network
Cable
Internet
Performance Lite 2MP SD Camera - User Manual | Network Connection

7
or
IPC Computer
Network Cable Network Cable
Internet
3. Go to the router’s management interface through IE browser to forward the IP address and port of the camera in the “Virtual
Server”.
Router Setup
4. Open the IE browser and input its WAN IP and http port to access.
Access through static IP
Network connection
The setup steps are as follow:
1. Go to Config > Network > Port menu to set the port number.
2. Go to Config > Network > TCP/IP menu to set the IP address. Check “Use the following IP address” and then enter the static IP
address and other parameters.
3. Open the IE browser and enter its WAN IP and http port to access.
Performance Lite 2MP SD Camera - User Manual | Network Connection

8
Live View
Icon Description Icon Description
Motion alarm indicator icon Start/stop live view
Original size Snapshot
Appropriate size Start/stop record
Auto Zoom in
Full screen Zoom out
The following table is the instructions of the icons on the live view interface.
• The motion detection indicator will flash in live view interface only when the motion detection alarm is enabled.
• In full screen mode, double click on the mouse to exit or press the ESC key on the keyboard.
Performance Lite 2MP SD Camera - User Manual | List View

9
Configuration
System Configuration
Basic Information
In the “Basic Information” interface, the system information of the device is listed.
Date & Time
Go to Config > System > Date and Time. Please refer to the following interface.
Select the time zone and DST as desired.
Performance Lite 2MP SD Camera - User Manual | Configuration

10
Local Configuration
Go to Config > System > Local Config to set up the storage path of captured pictures and recorded videos on the local PC. There
is also an option to enable or disable the bitrate display in the recorded files.
Storage
Go to Config > System > Storage.
Note: The following functions are only available for the models with SD card slot.
• SD Card Management
Click the “Format” button to format the SD card. All data will be cleared by clicking this button.
Click the “Eject” button to stop writing data to SD card. Then the SD card can be ejected safely.
• Schedule Recording Settings
1. Go to Config > System > Storage > Record to go to the interface as shown below.
2. Set record stream, pre-record time and cycle writing.
Pre Record Time: Set the time to record before the actual recording begins.
3. Set schedule recording. Check “Enable Schedule Record” and set the schedule.
Click the “Date and Time” tab to set the time mode.
Performance Lite 2MP SD Camera - User Manual | Configuration

11
Weekly schedule
Set the alarm time from Monday to Sunday for a single week. Each day is divided in one hour increments. Green means scheduled.
Blank means unscheduled.
“Add”: Add the schedule for a special day. Drag the mouse to set the time on the timeline.
“Erase”: Delete the schedule. Drag the mouse to erase the time on the timeline.
Manual Input: Click it for a specific day to enter specific start and end times. This adds more granularities (minutes).
Day schedule
Set the alarm time for a special day, such as a holiday.
Note: Holiday schedule takes priority over weekly schedule.
Performance Lite 2MP SD Camera - User Manual | Configuration

12
Image Configuration
Image Configuration includes five submenus: Display, Video/Audio, OSD, Video Mask and ROI Config.
Display Configuration
Go to Image > Display interface as shown below. The image’s brightness, contrast, hue and saturation and so on for common,
day and night mode can be set up separately. The image effect can be quickly seen by switching the configuration file.
Brightness: Set the brightness level of the camera’s image.
Contrast: Set the color difference between the brightest and darkest parts.
Hue: Set the total color degree of the image.
Saturation: Set the degree of color purity. The purer the color is, the brighter the image is.
WDR: WDR can adjust the camera to provide a better image when there are both very bright and very dark areas simultaneously
in the field of the view by lowering the brightness of the bright area and increasing the brightness of the dark area.
Sharpness: Set the resolution level of the image plane and the sharpness level of the image edge.
Noise Reduction: Decrease the noise and make the image more thorough. Increasing the value will make the noise reduction
effect better but it will reduce the image resolution.
Defog: Activating this function and setting an appropriate value as needed in foggy, dusty, smoggy or rainy environment to get
clear images.
Antiflicker:
• Off: disables the anti-flicker function. This is used mostly in outdoor installations.
• 50Hz: reduces flicker in 50Hz lighting conditions.
• 60Hz: reduces flicker in 60Hz lighting conditions.
White Balance: Adjust the color temperature according to the environment automatically.
Frequency: 50Hz and 60Hz can be optional.
Day/night Mode: Please choose the mode as needed.
Sensitivity: High, middle and low can be selected for switching back and forth from day to night modes.
Performance Lite 2MP SD Camera - User Manual | Configuration