Honeywell 7222 User manual

Models 7222, 7224, 7322 & 7324
FIRE RESISTANT VERTICAL FILE CABINETS
Read this manual carefully and never store it inside the cabinet!
Models 7222, 7224, 7322 & 7324
FIRE RESISTANT VERTICAL FILE CABINETS
Note: During shipment, the gypsum insulation of your Honeywell file
cabinet may create a film of dust on the exterior and interior of the file.
This is a normal settling process. Simply wiping the cabinet and drawers
with a damp cloth will remove the dust. Honeywell files are asbestos free.
PACKAGE CONTENTS
1– Vertical File Cabinet
1– Operation Manual
2– Entry Keys
For missing parts or difficulty operating your
cabinet, please contact our Consumer
Assistance Department by telephone.
US/Canada 1-877-354-5457 (Toll Free)
Australia 0011-800-5325-7000 (Toll Free)
Germany 00-800-5325-7000 (Toll Free)
IMPORTANT: DO NOT RETURN CABINET TO STORE!
Store will not accept returned products without prior authorization. You must
first contact our consumer assistance department.
CABINET SERIAL NUMBER
Whenever contacting our Consumer Assistance Department, you will need to
provide them with the serial number of your cabinet.
The serial number tag is located on the
lower right front corner of the cabinet.
IMPORTANT: Do Not Remove Tags!
These are needed if you lose your keys.

UNPACKING & MOVING CABINET
CAUTION! Honeywell file cabinets and drawers are heavy! For safety
always use proper moving equipment and padding when moving cabinets.
Remove Cabinet from the Pallet
1. Remove rubber stops from the front and sides of the pallet.
2. Spin the cabinet to set sideways across the pallet.
3. Slide the cabinet so that the back of the cabinet will tilt and rest on the floor.
4. Push back on the front of the cabinet to raise front of the bottom of the
pallet.
5. Slide pallet out of the way and set cabinet on the floor
Moving The File Into Place
xDo not use the file’s handle to lift or move the file; damage to the latching
system may result.
xFor the lock to function properly, the file must be leveled from side to side
and front to back. Place shims at the bottom corners of the file as
necessary to level the file.
xMoving Honeywell file cabinets into position may be facilitated by removing
the drawers.
DRAWER REMOVAL & INSTALLATION
IMPORTANT: Drawers are very heavy. Two or more persons are required
when handling the drawers. Note that each drawer has a drawer number decal
on the right side of the drawer. Drawers are numbered from top to bottom and
each must be replaced in the same cavity from which it was removed.
Fig. 1 .
DRAWER REMOVAL & INSTALLATION CONTINUED
To Remove Drawers
1. Extend drawer fully out.
2. Grasp front of drawer on each side and lift to release front tabs of slides
from drawer. (Fig. 1)
3. Place one hand underneath the drawer for support and pull one slide
forward to release the rear tab.(Fig. 1), repeat for other slide
4. Holding drawer head with both hands, pull drawer clear of slides and out of
cavity.
5. Push suspensions and stabilizers back into the drawers
To Install Drawers
1. Pull suspensions and stabilizers out until they are fully extended.
2. Place drawer into opening in between slides and align rear tab of slide with
the appropriate notch and insert.
3. Pull drawer forward until front tabs are aligned, insert front tabs
4. Close drawer and check for free movement and equal gap on both sides of
drawer.
If necessary, lightly loosen stabilizer screws and move drawer in direction of
excessive gap. Tighten screws and recheck gap.
LOCKING & UNLOCKING DRAWERS
Do not attempt to close drawer when the lock bolt is extended; damage to
cabinet and/or lock may result.
To Lock
1. Make sure all drawers are
closed before locking
2. Push the lock plunger in until
it snaps into place.
To Unlock
1. Insert key into lock.
2. Turn to the right or left until
the plunger pops out.

LOCK BYPASS FEATURE
Lock Bypass Feature
The lock bypass lever is designed to allow access to certain drawers while
others remain locked.
If one or more of the drawers will not lock, check the lock bypass lever. The
bypass lever needs to be in the deactivated position in order for the drawer
to lock. Below are instructions that will help in activating and deactivating the
lock bypass lever.
To activate bypass:
Lift the lever with your
thumb until it rests above
the dimple at the top of side
catch assembly (Fig. 2).
The drawer will NOT lock
with the lever in this
position.
Fig. 2
To deactivate bypass:
Press down on the lever
until it is positioned below
the dimple and rests on the
channel that is a formed
feature of the side catch
assembly (Fig. 3).
The drawer will now lock
with the lever in this
position
Fig. 3
FILLING THE CABINET DRAWERS
Maximum recommended weight is 60 Lbs. /27 kg per drawer.
The weight should be evenly distributed throughout the file. Exceeding the
maximum recommended capacity may seriously damage your file’s suspension.
U.S. – Letter & Legal Size Files International – A4 Foolscap Files
REMEMBER!
Open drawers do not provide protection. Honeywell cabinets use the latest
technology to protect your valuables. During a fire, the insulation is designed to
release moisture to create a protective barrier. If you are storing valuables that
are sensitive to moisture, such as stamps, money, watches, etc., please place
them in a sealed, humidity resistant container to protect them from moisture
damage

TROUBLESHOOTING
PROBLEM: Keylock Will Not Stay In
POSSIBLE CAUSE: Loose material in the black encasement.
POSSIBLE SOLUTION: Open lock drawer and look inside the backside of the
encasement for any loose material.
POSSIBLE SOLUTION: Ensure the keylock moves freely in the encasement.
POSSIBLE CAUSE: Drawer(s) do not close properly:
POSSIBLE SOLUTION: Make sure all drawers are closed and that there is
not anything in the drawerhead track or behind the drawer body.
POSSIBLE SOLUTION: Make sure the drawer(s) are in the right opening.
Each drawer is numbered on the right hand side with the lock drawer being
#1.
POSSIBLE CAUSE: Side catch(es) not adjusted properly.
POSSIBLE SOLUTION: Close all of the drawers and holding keylock in the
locked position, try to open all of the drawers. There should be some
movement in each side catch.
PROBLEM: Key Goes In, But 1 or More Drawers Will Not Open
POSSIBLE CAUSE: Loose or missing lock rod pins.
POSSIBLE SOLUTION: Check the lock pins for each drawer located on the
lock rod on the right hand side of the cabinet and tighten pins with a flat
screwdriver.
POSSIBLE SOLUTION: Make sure the lock pin in the eccentric is in place
and securely fastened to the lock bar.
POSSIBLE CAUSE: Side catch flipper hanging on the lock bypass dimple.
POSSIBLE SOLUTION: Make sure the lock bypass is deactivated. Identify
the lock/unlock position with operating sticker located directly behind the side
catch.
POSSIBLE CAUSE: Overfilling drawers.
POSSIBLE SOLUTION: Over filling of drawers can cause the drawers to
bulge and the side catch to rub against the side of the cabinet and hang in the
up or bypass position.
TROUBLESHOOTING CONTINUED
PROBLEM: Closing Drawers with the Keylock Pushed In, Side Catch
Flipper Raises Above the Bypass Dimple
POSSIBLE CAUSE: Side catch is set too low.
POSSIBLE SOLUTION: Follow the side catch adjustment procedure to adjust
side catch up.
PROBLEM: Cabinet Will Not Unlock
POSSIBLE CAUSE: Side catches are set too low.
POSSIBLE SOLUTION: Firmly grasp the handle of the top drawer and
depress thumb latch. Jerk drawer until it opens.
POSSIBLE SOLUTION: Follow the side catch adjustment procedure to adjust
the side catch up.
POSSIBLE CAUSE: Keylock will not spring out but cabinet will open if
keylock is pulled out.
POSSIBLE SOLUTION: Lubricate keylock with WD-40.
POSSIBLE SOLUTION: Check the encasement for loose material.
POSSIBLE SOLUTION: Check lock rod and eccentric assembly for proper
movement.
PROBLEM: Drawer Drops When Pulled Out
POSSIBLE CAUSE: Suspensions not properly set.
POSSIBLE SOLUTION: Remove suspension and spread the rear of the
suspension to make sure the bearings of the suspension stay under the top
lip of the side channel.
POSSIBLE CAUSE: Side channel bent.
POSSIBLE SOLUTION: Remove drawer and suspension, using a crescent
wrench, bend the top rear of both side channels down so that they are at a
90° angle or less.
POSSIBLE CAUSE: Broken rail on drawer body.
POSSIBLE SOLUTION: Open the drawer and check side rails on each side
of the drawer body. If broken contact the factory for replacement parts and
instructions.
POSSIBLE CAUSE: Broken bearing on suspension.
POSSIBLE SOLUTION: Check suspension bearings for flat or broken edges.
Contact the factory for parts.

BYPASS/SIDE CATCH ADJUSTMENT
About Bypass
The file drawer lock bypass lever is designed to allow access to certain
drawers while others remain locked. If one or more of the drawers will not
lock, check the lock bypass lever. The bypass lever needs to be in the
deactivated position in order for the drawer to lock.
When to Adjust
Due to the settling of the drawers, it may be necessary to make adjustments
to the side catch. If adjustment is necessary the first step should be to
determine which direction the side catch should be moved. If the side catch
"bumps" on the lock pin when the drawer is opened, the side catch should be
moved upward. When locked the drawers should have approximately 1/8
inch of play. If the lock up is too tight the side catch should be moved toward
the back of the file.
How to Adjust
To adjust the side catch, remove the two anchor bolts located at the bottom of
the side catch. Loosen the two adjustable bolts and move the side catch as
needed, then re-tighten bolts. It will be necessary to drill new holes through
the drawer body using a #20 drill bit to re-install the anchor bolts.
ORDERING REPLACEMENT KEYS
The following information is required to order replacement keys:
1. PROOF OF OWNERSHIP (1 of 2 Options Below)
SALES RECEIPT & IDENTIFICATION – INTERNATIONAL ONLY!
xCopy of sales receipt showing Store, Date & Product Description.
xCopy of your picture I.D. (Drivers license, passport, regular I.D.).
PRODUCT OWNERSHIP VERIFICATION FORM
If sales receipt is not available, contact us by email or telephone to
request a “Product Ownership Verification Form”.
2. ORDER INFORMATION
CONTACT INFORMATION
xName & Shipping Address
xE-mail address (If Available)
xTelephone Number
xBest Time to Contact You
PRODUCT INFORMATION
xSafe Model #
xSafe Serial #
xLock Key #
xQuantity of Keys Ordered
ORDERING REPLACEMENT KEYS CONTINUED
3. PAYMENT INFORMATION
AMOUNT DUE
xPer Key:
US/Canada - $12.00 (USD)
Australia - $15.00 (AUD)
Germany - €11.00 (EU)
METHOD OF PAYMENT
xTelephone:
Visa or MasterCard
xMail:
Check or Money Order
xExpress Delivery: Contact us for Additional Charges
Subject to change without prior notification.
CONTACTING CUSTOMER SERVICE
EMAIL: [e-mail]
ADDRESS: Consumer Assistance Dept.
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746 USA
TELEPHONE: US/Canada 1-877-354-5457 (Toll Free)
Australia 0011-800-5325-7000 (Toll Free)
Germany 00-800-5325-7000 (Toll Free)
CALL CENTER HOURS: US/Canada 7am – 5pm (PST) Mon -Fri
Australia 12am -10am (AEST) Tue–Sat
Germany 4pm -2am (CET) Mon–Fri
CALL BACK HOURS: Australia 12am – 3pm (AEST) Tue–Sat
Germany 4pm -7am (CET) Mon–Fri
INTERNATIONAL CALL BACK HOURS:
If you need to speak with a consumer assistant and cannot contact us during
the Call Center hours above, please send an email or leave a telephone
message, including your Name, Telephone Number and the best time for us
to contact you during the Call Back hours above. Your call will be returned
next working day.

LIMITED WARRANTY
LH Licensed Products, Inc., (“LHLP, Inc.”) warrants that for a period of seven (7)
years from the date of purchase, this product will be free from structural or
mechanical defects resulting from materials or workmanship. LHLP, Inc., at its
sole option and as the purchaser’s sole remedy under this warranty, will repair or
replace this product or any component of the product found to be defective
during the warranty period. Replacement or repair will be made with a new or
remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. THIS
IS YOUR EXCLUSIVE WARRANTY.
This warranty is only valid for the original retail purchaser from the date of initial
retail purchase and is not transferable. You must keep the original sales receipt.
Proof of purchase is required to obtain warranty service.
LHLP, Inc. dealers, service centers, or retail stores selling this product do not
have the right to alter, modify or in any way change the terms and conditions of
this warranty.
This warranty does not apply to the finish on the product. This warranty does not
cover normal wear and tear of parts or damage resulting from any of the
following: negligent use or misuse of the product, use contrary to the operating
instructions, disassembly, repair or alteration by anyone other than LHLP, Inc. or
an authorized service center, improper installation, or exposure to extremes of
heat or humidity. Further, the warranty does not cover Acts of God, such as fire,
flood, hurricanes and tornadoes.
LHLP, Inc. shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty or otherwise relating to
the sale of this product. LHLP, Inc. is also not responsible for: costs associated
with removing or installing the product; damage or loss of the contents of the
product; nor for the unauthorized removal of the contents; or damages incurred
during shipment.
THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND
LHLP, INC. DISCLAIMS ANY AND ALL OTHER COVENANTS AND
WARRANTIES.
Except to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration to the
duration of the above warranty period. Some states, provinces or jurisdictions do
not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or
exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights that vary from state to state, or province to
province, or jurisdiction to jurisdiction.
LIFETIME AFTER-FIRE REPLACEMENT GUARANTEE
If this Honeywell UL classified fire resistant product was purchased from LH
Licensed Products, Inc. (“LHLP”) and is damaged by fire at any time while still
owned by you (the original owner), LHLP will ship a free replacement if you send
the following to Customer Service, LH Licensed Products, Inc., 860 E. Sandhill
Ave., Carson, CA 90746 USA:
1. Your name, mailing address, email address, and phone number with area
code;
2. A description of the fire, the model number and a photo of the burned unit, and
a copy of the report from the fire department, insurance or police.
Freight on the replacement unit is not included in the guarantee and must be paid
by the consumer. If an identical product is no longer available, LHLP will provide
a similar unit from its current product line. LHLP is not responsible for any loss or
damage to the contents of the safe.
The Honeywell Trademark is used under license from
Honeywell International Inc. Honeywell International Inc. makes
no representations or warranties with respect to this product.