Honeywell IH25 User manual

Quick Start Guide
IH25
UHF RFID Reader
IH25-EN-QSG REV A

Mobile Terminal Socket
Power Button
UHF Antenna
Trigger Button
Type C Port
Charging Contacts
MODE Button
Status Indicators
Battery Cover
Release Screws
MODE
Introduction
The IH25 UHF RFID Reader provides Ultra High Frequency (UHF)
Radio Frequency Identification (RFID) connected to a mobile
terminal. The unit can read and write to bar code, QR code and
UHF RFID tags.

Install the battery before using the reader for the first time.
1. To access the battery compartment, remove the battery cover
screws and then the battery cover.
2. Insert the battery into the battery compartment with the tape at
the bottom.
3. Attach the battery cover and tighten the screws. Note that the
torque should be 3.5kg.f.
Battery Installation and Remove
2
1
To uninstall the battery, remove the battery cover screws and
then the battery cover. Pull the tape on the battery to pull the
battery out.
Tape
MODE
2
1
3.8V 4000 mAh
Tape

Before using the reader for the first time, ensure the battery is fully
charged.
To charge the reader, use the USB cable, the USB cable + AC
charge adapter or a docking station.
Solid amber: Charging
Solid green: Fully charged
USB Charge
AC Charge
Charging

MODE
Honeywell
Power
12V
Use the one slot or four-slot docking station to charge IH25 and
the mobile terminal. Note: when charging, make sure the
charging indicator is always on.
MODE
Honeywell
Power
12V
Docking Station Charge

2
1
1. Insert the mobile terminal into the case and press it down.
Note: When installing the bracket, pay attention to the angle and
strength so as not to damage the product.
2. Turn on power to the reader and the mobile terminal.
Use the mobile terminal to scan the QR code on the label
attached at the bottom of the reader’s main body.
QR
code
Fitting Device Case and Attaching Device

3. Check the stud on the bottom of the case and the socket on
the reader are clean and free from dirt or debris.
4. Align the stud with the socket, ensuring that it is parallel, and
press the two parts together firmly until they click into place.

1. Turn on power to the reader and it beeps one time.
2. Press and hold the MODE button for at least 3 seconds to
switch to RFID mode. The RFID indicator is on and then off after 5
seconds.
3. Press the trigger button to read tags.
RFID tags can be read when they are in range. The range (typical
0.2ft—20ft) at which a tag can be read depends on the tag type
and size and the number of tags in the field.
2
1
Reading RFID Tags

MODE
MODE
MODE
MODE Button and Status Indicators
Press the MODE button to light on the current mode light.
Release the button within 3 seconds, the mode light is off.
Press and hold the MODE button for at least 3 seconds to
switch between 1D/2D and RFID mode and the current
mode light is on.
Release the button, the current mode light is off.
Solid amber: Charging
Solid green: Fully charged
Red flash/ Green and amber flash alternately: Charge error
Solid red: Battery low warning (<20% capacity remaining.)
Blue slow flash: Bluetooth disconnected (two beeps
when disconnect from PDA)
Solid blue: Bluetooth connected (one beep when
connected successfully)

Important Safeguards
We recommend the use of Honeywell accessories and power
adapters. Use of any non-Honeywell accessories or power
adapters may cause damage not covered by the warranty.
We recommend use of Honeywell Li-ion battery packs. Use
of any non-Honeywell battery may result in damage not
covered by the warranty.
Ensure all components are dry prior to mating the unit and
batteries with peripheral devices. Mating wet components
may cause damage not covered by the warranty.
Ensure all components are dry prior to placing the battery in
the unit. Mating wet components may cause damage not
covered by the warranty.

To search our knowledge base for a solution or to log into the
Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
For the user guide and other documentation, go to
www.honeywellaidc.com.
For patent information, see www.hsmpats.com.
The Bluetooth® word mark and logos are owned by Bluetooth
SIG, Inc.
Other product names or marks mentioned in this document may
be trademarks or registered trademarks of other companies and
are the property of their respective owners.
For warranty information, go to www.honeywellaidc.com and click
Get Resources > Product Warranty.
Support
User Documentation
Limited Warranty
Patents
Trademarks

Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases
consult HII to determine whether any such changes have been
made. The information in this publication does not represent a
commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this materi-
al. HII disclaims all responsibility for the selection and use of
software and/or hardware to achieve intended
results.
This document contains proprietary information that is protected
by copyright. All rights are reserved. No part of this document may
be photocopied, reproduced, or translated into another language
without the prior written consent of HII.
Copyright © 2018 Honeywell International Inc. All rights reserved.
Disclaimer

1
IH25 (900 MHz) Compliance Insert
For Users in English-Speaking Regions
Users ofthisproduct are cautioned to use accessories and peripherals approved by Honeywell. The useof accessories other than those
recommended, or changes to this product that are not approved byHoneywell, may void the compliance of this product and may result in the
loss of the user’s authority to operate the equipment.
Battery, Charger, and Power Supply Information
Battery Recycling Information
Radiation Exposure Statement
Radio Wave Exposure and Specific Absorption Rate (SAR) Information
Use of antennas and accessories not authorized mayvoid the compliance ofthis product and may result in RF exposures beyond the limits
established for this equipment.
U.S.A. and Canada
U.S.A. Digital Emissions Compliance
This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standards. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,
including interference that can cause undesired operation.
This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, ifnotinstalled and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the radio or television receiving antenna.
•Increase the separation between the computer equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
•Consult the dealer or an experienced radio television technician for help.
Canadian Compliance
This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
CAN ICES-3 (B)/NMB-3(B)
Caution: This marking indicates that the user should read all included documentation before use.
Caution: For use with Honeywell battery pack Model BAT-EDA50 only. No user-serviceable parts.
Charge only in or with Honeywell recommended models adapter or charger.Use of incorrect charger may present a risk offire or
explosion. Promptly dispose of used battery pack according to the instruction.
Caution: The battery pack usedwith this product may ignite, create achemical burn hazard, explode, or release toxic materials if
mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from
children.
Li-ionLi-ion
This product contains or uses a lithium-ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent
battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid
waste stream. Contact your Honeywell Technologies Service Center for recycling or disposal information.
Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1,
Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European
Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation.
䕤ᇘᲈ䴆ໄᯢ
ൟ᮴㒓⬉ᲈ䴆ঞ⡍ᅮᬊ⥛6$5ⱘֵᙃ
㒣䆌ৃ㗠Փ⫼໽㒓ঞ݊䰘ӊˈৃ㛑Ӯᇐ㟈ᴀѻકⱘヺড়ᗻ᮴ᬜˈৠᯊ䖬ৃ㛑Ӯᇐ㟈5)ᲈ䴆䍙ߎᇍᴀ䆒໛԰ߎⱘ䰤ࠊDŽ
䄺˖ᴀ䆒໛ヺড়೑䰙䴲⬉⾏䕤ᇘֱᡸྨӮ,&1,53ǃ,(((&ǃ㕢೑㘨䙺䗮ֵྨӮᎹ⿟ᡔᴃ䚼2(7%XOOHWLQ
ǃࡴᣓ໻566󱂜⌆⬉Ꮉ󰵼ޚ࣪ྨӮ&(1(/(&㾘ᅮⱘᇘ乥5)䕤ᇘᲈ䴆䰤ࠊDŽ

3
Declaração de exposição à radiação
Informações sobre Exposição às Ondas de Rádio e Taxa de Absorção Específica (SAR)
O uso de antenas e acessórios não autorizados pode anular a conformidade deste produto eresultar em exposição a níveis de radiofrequência
superiores aos limites estabelecidos para este equipamento.
䗖⫼ѢЁ೑⫼᠋]KFQ
ᭀᴀѻકⱘ⫼᠋ˈ䇋ࡵᖙՓ⫼Honeywell䆌ৃⱘ䰘ӊ໪ೈ䆒໛DŽབᵰՓ⫼᥼㤤䰘ӊП໪ⱘ݊ᅗ䰘ӊˈ
៪᳾㒣Honeywell䆌ৃ㗠᪙㞾ᬍ㺙ᴀѻકˈ䛑ৃ㛑ӮՓᴀѻકⱘヺড়ᗻ᮴ᬜˈᑊৃ㛑Ӯᇐ㟈⫼᠋༅এ᪡԰ ᴀ䆒໛ⱘᴗ߽DŽ
⬉∴ǃܙ⬉఼⬉⑤ֵᙃ
⬉∴ಲᬊֵᙃ
䗖⫼ѢЁ೑⫼᠋
Atenção: Este equipamento atende aos limites de exposição a radiação de radiofrequência (RF) do International Commission on
Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1, Federal Communications Commission Office of Engineering and
Technology (OET) Boletim 65, Canada RSS-102 e European Committee for Electrotechnical Standardization (CENELEC).
⊼ᛣ˖䆹󰵼ᖫ㸼ᯢˈ⫼᠋ᑨ೼Փ⫼ࠡ䗮䇏᠔᳝䱣䰘ⱘ᭛ḷDŽ
⊼ᛣ˖ҙկϢ HoneywellBAT-EDA50. ൟ⬉∴㒘䜡ড়Փ⫼DŽ≵᳝ৃկ⫼᠋㓈ׂⱘ䳊䚼ӊDŽ
䇋ҙՓ⫼ൟোЎHoneywell推荐使用的电源适配器或ܙ⬉఼DŽՓ⫼ܙ⬉఼䫭䇃ৃ㛑ᓩ䍋☿♒៪⟚⚌DŽ䇋ḍ᥂䇈ᯢঞᯊ໘⧚⫼䖛ⱘ⬉∴
ࣙDŽ
⊼ᛣ˖䆹㺙㕂Ё᠔Փ⫼ⱘ⬉∴ࣙৃ㛑ⴔ☿ǃ䗴៤࣪ᄺ➗⚻䰽ǃ⟚⚌ˈ㗠Ϩབᵰ໘⧚ϡᔧӮ䞞ᬒ᳝↦⠽䋼DŽ䇋࣓⚻↕ǃߚ㾷
⬉∴ˈ៪㗙ࡴ⛁ࠄ 摄氏度ҹϞDŽ䇋࣓Փ⬉∴ⷁ䏃ˈҹܡᓩ䍋☿♒DŽ䇋ϡ㽕䅽ܓス᥹㾺ࠄ⬉∴DŽ
Li-ionLi-ion
ᴀѻકࣙ৿៪Փ⫼ϔഫ䫖⾏ᄤЏ⬉∴DŽ⬉∴䖒ࠄՓ⫼ᇓৢˈ䇋Ѹ⬅ড়Ḑⱘಲᬊ㗙៪䰽ᴤ᭭໘⧚㗙䖯㸠໘⧚DŽ䇋࣓ᇚ
Փ⫼ৢⱘ⬉∴⏋ৠ݊Ҫ೎ԧᑳᓗ⠽໘⧚DŽ䇋㘨㋏Honeywellᡔᴃ᳡ࡵЁᖗњ㾷᳝݇ಲᬊ៪໘⧚ⱘֵᙃDŽ
ѻકЁ᳝ᆇ⠽䋼ⱘৡ⿄ঞ৿䞣
ѻકЁ᳝ᆇ⠽䋼ⱘৡ⿄ঞ৿䞣
1DPHVDQGFRQWHQWRI+D]DUGRXV6XEVWDQFHVLQWKH3URGXFW
᳝ᆇ⠽䋼+D]DUGRXVVXEVWDQFH
䚼ӊৡ⿄3DUWV1DPH 䪙3E ∲+J 䬝&G ݁Ӌ䫀&U ໮⒈㘨㣃3%% ໮⒈Ѡ㣃䝮3%'(
⬉䏃ᵓϞⱘ䱊⫋ܗӊ咘䪰᥹༈ XO OO O O
ล᭭ⲪᵓϞⱘ咘䪰ጠӊ XO OO O O
ᴀ㸼Ḑձ᥂ 6-7 ⱘ㾘ᅮ㓪ࠊDŽ7KLVWDEOHLVFUHDWHGLQDFFRUGDQFHWR6-7
2㸼⼎䆹᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ *%7 󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ,QGLFDWHVWKDWWKLVKD]DUGRXV
VXEVWDQFHFRQWDLQHGLQDOORIWKHKRPRJHQHRXVPDWHULDOVIRUWKLVSDUWLVEHORZWKHOLPLWUHTXLUHPHQWLQ&KLQDV*%
7
;㸼⼎䆹᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ *%7󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖DŽ,QGLFDWHVWKDWWKLVKD]DUGRXV
VXEVWDQFHFRQWDLQHGLQDWOHDVWRQHRIWKHKRPRJHQHRXVPDWHULDOVIRUWKLVSDUWLVDERYHWKHOLPLWUHTXLUHPHQWLQ
&KLQDV*%7
5
2
Pour les utilisateurs canadiens
Les utilisateurs de ce produit sont avisés d’utiliser des accessoires et des périphériques approuvés par Honeywell. L’utilisation
d’accessoires autres que ceux recommandés ou des changements à ceproduit qui ne sont pas approuvés par Honeywell peuvent annuler la
conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser l’équipement.
Informations sur la batterie, le chargeur et le bloc d'alimentation
Informations pour le recyclage de la pile
Énoncé sur l'exposition aux radiations
Information sur l’exposition aux ondes radioélectriques et sur le débit d’absorption spécifique (DAS)
L’utilisation d’antennes et d’accessoires non autorisés peut annuler la conformité de cet appareil et peut causer une exposition aux RF au-delà
des limites établies pour cet équipement.
Conformité aux normes sur les émissions numériques
Ce périphérique est conforme aux normes RSS exemptes de licence d'Industrie Canada. L’utilisation est assujettie aux deux conditions
suivantes : (1) Ce dispositif ne doit pas causer d’interférence dommageable et(2) Ce dispositif doit tolérer toute interférence, incluant
l’interférence pouvant causer un fonctionnement indésirable.
CAN ICES-3 (B)/NMB-3 (B)
Para Usuários do Brasil (pt)
Os usuários deste produto devem usar acessórios e periféricos aprovados pela Honeywell. Usar acessórios não recomendados, ou fazer
alterações neste produto não aprovadas pela Honeywell,poderá anular a conformidade deste produto e resultar na perda da permissão do
usuário de utilizar o equipamento.
Informações sobre a bateria, carregador e fonte de alimentação
Infomações de Reciclagem de Bateria
Mise en garde : Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse.
Mise en garde : Pour utilisation seulement avec bloc-batterie Honeywell modèle BAT-EDA50. Il ne contient aucune pièce réparable
par l’utilisateur. Ne charger qu’avec les dispositifs modèles recommandés par Honeywell adaptateur ou chargeur.L’utilisation d’un
mauvais chargeur pourrait constituer un risque d’incendie ou d’explosion. Mettre rapidement au rebut tout bloc-piles usé,
conformément aux instructions.
Mise en garde : Ce bloc-piles peut prendre feu, constituer un risque de brûlure chimique, exploser ou dégager des substances
toxiques s’il estmanipulé de façon inappropriée. Ne pas jeter au feu, démonter ou chauff er à plus de 100 °C. Ne pas court-
circuiter; cela pourrait causer des brûlures. Garder hors de la portée des enfants.
Li-ionLi-ion
Ce produit contient ou utilise une pile principale au lithium-ion (Li-ion). Lorsque la batterie atteint la fin de sa durée de vie
utile, la batterie usées doivent être mises aux rebuts par un agent de recyclage ou un manipulateur de matériaux dangereux
agréé. Il ne faut pas mélanger la batterie aux autres déchets solides. Pour plus d’informations sur le recyclage ou la mise aux
rebuts, contacter votre centre de services Honeywell.
Avertissement : Cet équipement est conforme à la Commission internationale de protection contre les rayonnements non ionisants
(CIPRNI), à la norme IEEE C95.1, au bulletin 65 de l’OET (Federal Communications Commission Office of Engineering and
Technology), à la norme Canada RSS-102 et aux limites Comité Européen de Normalisation Électrotechnique (CENELEC)
d’exposition à des rayonnements radioélectriques.
Cuidado: Esta identificação indica que o usuário deve ler toda a documentação fornecida antes do uso.
Cuidado: Para uso apenas com a bateria modelo BAT-EDA50 da Honeywell.Este equipamento não contém peças que possam ser
reparadas pelo usuário.
Carregar apenas com os modelos de carregadores da adaptador ou carregador de modelos recomendado pela Honeywell.Ouso de um
carregador incorreto pode gerar risco de incêndio ou explosão. Descartar imediatamente as baterias usadas segundo as instruções
fornecidas.
Cuidado: A bateria utilizada neste dispositivo pode pegar fogo, criar risco de queimadura química, explodir ou exalar materiais
tóxicos se abusada. Não incinerar, desmontar nem aquecer a bateria a mais de 100 °C . Não provocar curto-circuito, pois pode
causar queimaduras. Manter afastada decrianças.
Li-ionLi-ion
Este produto contém ou usa uma bateria principal de íon de lítio (Li-ion). Quando a bateria chega ao fim da sua vida útil, deve
ser descartada por um profissional de reciclagem qualificado ou por um especialista no manuseio de materiais perigosos.
Não misture abateria com fluxo de lixo sólido. Entre em contato com seu Centro de Serviços de Tecnologia Honeywell para
informações dereciclagem ou descarte.