Honeywell H2D2PR1 User manual

H2D2PR1(X) 1080p TDN IR Ball IP Camera
Document 800-17073V1 – Rev A – 07/2014 1
Quick Installation Guide
Document 800-17073V1 — Rev A — 07/2014
Thank you for purchasing a H2D2PR1(X) 1080p
True Day/Night IR Ball IP Camera to complement
your Honeywell Embedded NVR. Follow the
instructions in this guide to install and log in to
your camera. For instructions on configuring the
camera, refer to the Performance Series IP
Cameras User Guide on the software and
documentation CD that came with your camera. If
you require additional assistance, please call the
number shown below.
Cautions and Warnings
WARNING To ensure compliance with electrical safety standards this product is
intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,
on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE
802.3af PoE standard.
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.
Regulatory Statements
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Important Safeguards
• Read and keep these instructions.
• Do not aim the camera toward an bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the
operating temperature is outside the recommended range of -4°F to 140°F (–20°C to 60°C).
Note Do not apply power to the camera before completing installation.
Note Confirm the installation surface can support at least three times the weight of the camera plus
the bracket.

H2D2PR1(X) 1080p TDN IR Ball IP Camera
www.honeywell.com/security
[phone] (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-17073V1 – Rev A – 07/2014
© 2014 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
or damaged, contact your dealer immediately.
Required tools:
• A Phillips screwdriver
• A drill with an appropriately-sized drill bit for pre-drilling holes for the screw anchors.
CAUTION Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain your
warranty.
Removing the Ball Camera from the Base
From the back of the camera base, push the ball camera free from the gland cover on the
camera base. Set the ball camera body aside.
Preparing the Mounting Surface
1. Place the mounting template on the mounting surface where you want to install the camera.
2. Drill three (3) holes in the mounting surface for the wall anchors. Insert the wall anchors.
3. Drill an appropriately sized hole and pull the cables through the mounting surface.
Mounting the Camera
1. Route the cables through the camera base.
2. Align the screw holes on the camera base with the plastic wall anchors.
3. Insert the three self-tapping screws through the holes in the camera base, into the wall
anchors, and then tighten them to secure the camera base in place.
Installing and Adjusting the Ball Camera
1. Loosen, but do not remove, the M3X8 cross-recessed pan head slot screw on the camera
base. This screw secures the gland cover and camera in place.
2. Adjust the gland cover to the desired position, and then re-tighten the M3X8 cross-recessed
pan head slot screw to secure the gland cover in place.
3. Connect the IP cable to the RJ-45 port on the ball camera.
4. Firmly push the ball camera body back into the gland cover on the camera base until it
securely clicks into place.
5. Adjust the lens to the desired angle.
Installing the Decorative Ring
When you have achieved the desired field of view, install the decorative ring.
1. Align the three tabs on the decorative ring with the slots on the camera base.
2. Turn the decorative ring clockwise until it securely clicks into place.
•Camera
• Documentation CD
• Quick install guide
• Self-tapping screws (×4)
• Plastic wall anchors (×4)
• Mounting template
M3X18 self-tapping
Phillips pan head screw
Ceiling or wall
Wall anchor
Camera base
ST3x18 self-tapping screw
Gland cover
Decorative ring
Ball camera body
1
2
3
4
5