Honeywell HCC10 User manual

User Guide
High Resolution
Indoor Box Camera
HCC10
HCC10X
HCC210
HCC210X
Document 800-15952 – Rev A – 09/2013

2www.honeywell.com/security
WARNING To prevent the risk of fire or
electric shock hazard, do not expose this
camera to rain or moisture.
Information to the User: This equipment has been tested and
found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residen-
tial area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme
NMB-003 du Canada.
The manufacturer declares that the equipment supplied with this
guide is compliant with the essential requirements of the EMC
Directive 2004/108/EC, the General Product Safety Directive
2001/95/EC and the RoHS Directive 2011/65/EU, conforming to
the requirements of standards EN 55022 for emissions,
EN 50130-4 for immunity, EN 60950-1 for electrical equipment
safety, and EN 50581 for assessment of electrical and electronic
products with respect to the restriction of hazardous substances
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DO NOT OPEN
RISK OF ELECTRIC SHOCK

800-15952 - A - 09/2013 3
Safety Instructions 1
Read Instructions
Read all of the safety and operating instructions before
using the product and retain them for future reference.
Cleaning
Turn off the power and clean with a dry, soft cloth.
Do not use liquid cleaners or aerosol cleaners.
Attachments
Do not use attachments not recommended by the
manufacturer as doing so may result in fire, electric
shock, or serious injury.
Water and Moisture
Do not use this product near water or moisture.
Mounting
Follow the manufacturer’s instructions when mounting
the product. Use only mounting accessories
recommended by the manufacturer.
Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supplied to your facility,
consult your equipment dealer or local power
company.
Ventilation
Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions to ensure
reliable operation of the product and to protect it from
overheating.
Servicing
Do not attempt to service this product yourself. Refer all
servicing to qualified service personnel.

4www.honeywell.com/security
Precautions 1
Operating
Before using the camera, make sure the power supply
and video output are properly connected. When
operating the camera, if any abnormal condition or
malfunction is observed, stop using the camera
immediately and call your equipment dealer.
Handling
Do not disassemble the camera. Never touch the
internal parts of the camera.
Do not drop the camera or subject it to shocks and
vibrations.
When attaching or removing the lens, take care that no
moisture or dust enters the camera body.
Avoid viewing bright objects (such as light fixtures) for
extended periods, or bright vertical and horizontal lines
may appear on the screen.
Installation and storage
Do not point the camera at the sun as this could
damage the camera whether it is operating or not.
Do not install the camera where the temperature could
exceed the allowable range. Make sure the ambient
temperature is less than 104°F (40°C) in installations
intended for long term continuous operation.
Avoid installing or storing the camera in locations where
the camera may be exposed to:
• water/rain
• humidity
• dust
•radiation
• mechanical vibrations
• strong magnetic fields and electrical signals
Daily check
To maintain proper operation for surveillance use,
check the camera output every day for a clear and
focused picture.

800-15952 - A - 09/2013 5
Contents 1
Safety Instructions . . . . . . . . . . . . . . 3
Precautions . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . 6
Camera Parts Explained . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . 9
Installing the Lens . . . . . . . . . . . . . 9
Connecting the Wiring . . . . . . . . . . . 10
Mounting the Camera. . . . . . . . . . . . 11
Adjusting the Back Focus . . . . . . . . . 11
Menu Description . . . . . . . . . . . . . . . 12
Setup Menu . . . . . . . . . . . . . . . . . 13
About Iris, Shutter, and AGC Settings . . . 13
Lens . . . . . . . . . . . . . . . . . . . . . 14
Shutter/AGC . . . . . . . . . . . . . . . . 14
White Balance. . . . . . . . . . . . . . . . 15
Backlight . . . . . . . . . . . . . . . . . . 17
Picture Adjust . . . . . . . . . . . . . . . . 18
ATR . . . . . . . . . . . . . . . . . . . . . 18
Motion Detection . . . . . . . . . . . . . . 19
Privacy . . . . . . . . . . . . . . . . . . . 20
Day/Night . . . . . . . . . . . . . . . . . . 20
Noise Reduction . . . . . . . . . . . . . . 22
Camera ID. . . . . . . . . . . . . . . . . . 22
Sync . . . . . . . . . . . . . . . . . . . . . 23
Language . . . . . . . . . . . . . . . . . . 24
Camera Reset . . . . . . . . . . . . . . . . 24
Save All/Exit . . . . . . . . . . . . . . . . . 24
Specifications . . . . . . . . . . . . . . . . 25

6www.honeywell.com/security
Features 1
High sensitivity 1/3-inch CCD with on-chip micro
lenses and low-noise digital signal processing circuit
provides sensitivity down to 0.1 lux at F1.2, 50 IRE.
High quality image Horizontal resolution of 600 TVL
(HCC10/HCC10X) or 650 TVL (HCC210/HCC210X).
Digital signal processing with optimization of control
program and image correction algorithm.
BLC/HLC When strong light enters the scene back-
ground (such as from a spotlight or window), backlight
compensation automatically adjusts the video level to
preserve visibility. Highlight compensation masks
bright spots in a scene.
White balance Seven user-selectable white balance
control modes for varying conditions.
Iris function Drive output for video iris and DC iris
lens. Built-in electronic shutter allows eight shutter
speeds up to 1/100000 second. CCD iris function auto-
matically sets picture brightness by changing the
shutter speed of the camera according to the incident
light when using a manual iris lens.
Other functions
•Noisereduction
• Digital wide dynamic range
• 4 motion detection zones
• 8 privacy zones
• Picture adjustment for mirror, brightness, contrast,
sharpness, hue, and gain
• User-definable camera name
• 24 V AC or 12 V DC power source
• C or CS mount lenses

800-15952 - A - 09/2013 7
Camera Parts Explained 1
Lens mount
Use when installing the lens. C-mount lens
uses a C-mount adapter. CS-mount lens
does not need a C-mount adapter.
Back Focus screw
Use to adjust the back focus.
Lens mount cap
Use to cap the lens mount
when the lens is not attached.
C-mount adapter
Use to install a C-mount lens.
Remove to install a CS-mount lens.
Turn counterclockwise to remove.
1/4-20 UNC Mounting Hole
Use to install the camera to a tripod.
1/4-20 UNC Mounting Hole
Use to install the camera to a tripod.

8www.honeywell.com/security
VIDEO OUT
PWR
RS-485 ALARM
~ AC 24V ~
– DC 12V +
IN G D/N D-D+ OUT
OSD Menu Control
Video Output
(BNC)
Power LED
Alarm Input, Ground,
D/N, Alarm Output
Power Input
Connect to a 24 V AC or 12 V DC
power source. Do not connect the
power source until all other
connections have been
completed.
RS-485 Ports (D+, D–)
Ground

800-15952 - A - 09/2013 9
Camera Installation 1
Installing the Lens
1. Remove the lens mount cap from the camera
(if present).
2. Screw the lens clockwise onto the lens mount of
the camera (A). If you are using a C-mount lens,
you will need to attach the C-mount adapter first.
3. Connect the auto-iris drive cable to the 4-pin
interface on the side of the camera (B).
Use a Suitable Lens
• The camera can use CS-mount lenses or C-mount
lenses. C-mount lens require a C-mount adapter.
• Use a suitable lens for the required field of view.
The field of view for different focal length can be
obtained using the following formula:
A
B
Pin Signal
1Dampingcoil(–)
2Dampingcoil(+)
3 Drive coil (+)
4 Drive coil (–)
13
42
Pin Assignment

10 www.honeywell.com/security
Note Do not attach the C-mount adapter when using
a CS-mount lens.
Note In the illustration below, “L” should be as shown
in the table. If “L” exceeds the value in the table,
it may damage the inside of the camera and
make correct mounting impossible.
Connecting the Wiring
Note Do not turn on the power of any connected
equipment until all connections are completed.
1. Connect the power input of the camera to an
external 12 V DC or 24 V AC power supply.
2. Connect the video output of the camera to the
video input of your monitor.
Height of the
area of view
(m) =
A × Distance between camera and object (m)
Focal length of lens (mm)
Width of the
area of view
(m) =
B × Distance between camera and object (m)
Focal length of lens (mm)
Mounted Lens 1/2” Lens 1/3” Lens
A4.83.6
B6.44.8
Lens Back Focus
(mm)
Distance
“L” (mm)
C-mount * 17.526 < 9
CS-mount ** 12.5 < 4
Lens
L
Recommended
Focal Point
Back Focus
* With the C-mount adapter attached.
** With the C-mount adapter removed.
Power input
(12 V DC or 24 VAC)
Video output
Alarm I/O
D/N input
RS-485