Honeywell Performance HED1PR3 User manual

HED1PR3/HED3PR3 True Day/Night
Indoor/Outdoor IR Ball IP Camera
Quick Installation Guide
Document 800-21229V1— Rev A — 10/2015
Thank you for purchasing a HED1PR3/ HED3PR3
camera. Follow the
instructions in this guide to
install and log in to
your camera. For instructions
on configuring the
camera, refer to the
Performance Series IP
Cameras User Guide on
the software and
documentation CD that came
with your camera. If
you require additional
assistance, please call the
number shown
below.
Cautions and Warnings
WARNING To ensure compliance with electrical safety standards this product is
intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,
on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE
802.3af PoE standard.
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION Invisible LED radiation (850 nm). Avoid exposure to beam.
Regulatory Statements
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Important Safeguards
• Read and keep these instructions.
• Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the
operating temperature is outside the recommended range of -4°F to 140°F (–20°C to 60°C).
Note Do not apply power to the camera before completing installation.
Note Confirm the installation surface can support at least three times the weight of the camera.
Document 800-21229V1– Rev A – 10/2015 1
CAUTION
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN

Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
or damaged, contact your dealer immediately.
HED1PR3/HED3PR3 True Day/Night Indoor/Outdoor IR Ball IP Camera
Mounting the Camera
1. Route the cables through the camera base.
2. Align the screw holes on the camera base with the plastic wall anchors.
3. Insert the three self-tapping screws through the holes in the camera base, into the wall
• Camera
• Documentation CD
• Quick install guide
Required tools:
• A Phillips screwdriver
• Self-tapping screws (×3)
• Plastic wall anchors (×3)
• Mounting template
anchors, and then tighten them to secure the camera base in place.
Installing and Adjusting the Ball Camera
1. Connect the Ethernet cable to the RJ-45 port on the ball camera.
2. If the other end of the Ethernet cable is NOT connected to a PoE (Power-over-Ethernet)
switch or NVR, connect the power connector of the camera to a 12-V DC power source.
3. Reattach the cover to the base, and then move the ball camera body to the desired position.
CAUTION Installation and servicing should be performed only by qualified
and
experienced technicians to conform to all local codes and to maintain your
warranty.
Installing the Decorative Ring
Ceiling or wall
Wall anchor
Camera base
ST3x18 self
Gland cover
Decorative ring
Ball camera body
When you have achieved the desired field of view with the camera’s web viewer or a NVR’s display,
install the decorative ring.
1. Align the three tabs on the decorative ring with the slots on the camera base.
2. Turn the decorative ring clockwise until it securely clicks into place.
Logging On to the Camera
Camera connected to a PoE port of the Honeywell Embedded NVR can be configured with the NVR
directly.
To log on to the camera with a PC, install the Honeywell Config Tool from the software and
documentation CD, find the camera and open the web browser with the Honeywell Config Tool. The
default user name is admin (case-sensitive) and the default password is 1234.
Removing the Ball Camera from the Base
Turn the decorative ring clockwise out of the camera base and separate the gland cover from
the camera base. Set the ball camera body aside.
Preparing the Mounting Surface
1. Place the mounting template on the mounting surface where you want to install the camera.
2. Drill three (3) holes in the mounting surface for the wall anchors. Insert the wall anchors.
3. Drill an appropriately sized hole and pull the cables through the mounting surface.
Document 800-21229V1 – Rev A – 10/2015
© 2015 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
www.honeywell.com/security
[phone]
(North America only)
www.honeywell.com/security/uk
[phone]
(Europe only)
www.asia.security.honeywell.com
[phone]
(Asia Pacific only)
1
2
3
4
5
• A drill with an appropriately-sized drill bit for pre-drilling holes for the screw.
6