Honeywell HD4D3S User manual

Configuration Guide
HD4D Series
Document 800-08379 – Rev B – 05/11
Fixed Minidome Camera
HD4D3S HD4D3SX
HD4D9S HD4D9SX
HD4DAFS HD4DAFSX
HD4DIRS HD4DIRSX

2
Revisions
Issue Date Revisions
A04/11Newdocument.
B 5/11 Operating temperature upper limit changed to 131°F (55°C).
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
DO NOT OPEN
RISK OF ELECTRIC SHOCK

Document 800-08379 Rev B 3
05/11
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Programming the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Exposure Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Color Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Day&Night Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Motion Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Privacy Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Sync Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4
Introduction
This document provides instructions for configuring the following HD4D Series indoor/outdoor
vandal-resistant mini fixed dome cameras:
•HD4D3S(X) 3.3–12 mm Vari-focal Auto Iris lens
•HD4D9S(X) 9–22 mm Vari-focal Auto Iris lens
•HD4DAFS(X) 2.9–8.5 mm Auto Focus lens
•HD4DIRS(X) 3.3–12 mm Vari-focal Auto Iris lens, 18 LEDs
These instructions are intended for system installers, administrators, and operators.

Document 800-08379 Rev B 5
05/11
Programming the Camera
The camera is programmed using the on-screen display (OSD) menus. You may need to connect a
portable monitor during installation using the supplied adapter cable.
To access the OSD menu system, press the OSD controller joystick located on the camera control
board. Move the joystick left or right, up or down, to navigate through the menus. Menu icons are
located along the top of each menu screen to allow easy programming.
The camera has the following OSD menu structure:
1. EXPOSURE
LENS
E. SHUTTER
BLC
MAX_DR
AGC
SENSE_UP
2. COLOR
WB MODE
R-Y GAIN
B-Y GAIN
3. DAY&NIGHT
D&N MODE
4. FUNCTION
MIRROR
SHARPNESS
GAMMA
3D DNR
D_ZOOM
SLC
HME
DIS
5. MOTION
MOTION
SET WINDOW
ALL SET
ALL CLEAR
SENSITI.
SHOW INDI.
DELAY OUT
6. PRIVACY
MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
7. SYNC
SYNC MODE
V_PHASE
8. SETUP
CAMERA ID
TITLE
DPC
OMNI LENS*
* HD4DAFS Only
9. EXIT
EXIT
SAVE&EXIT
FACTORY SET
OSD
controller
Monitor out

6
Exposure Menu
EXPOSURE LENS
Note Only DC mode is supported at this time. Choosing MANUAL mode may cause the camera to
operate incorrectly.
Select DC. Press the OSD controller joystick to adjust the brightness level of the monitor screen.
Select a value from 0to 99 (99 = brightest).

Document 800-08379 Rev B 7
05/11
EXPOSURE E. SHUTTER (Electronic Shutter)
You can select from 18 different shutter
speed levels, from X256 to 1/100000. The
default shutter speed is 1/60.
Note The SENSE_UP menu cannot be
controlled if the E.SHUTTER
setting is above 1/250.
Select 1/100FLC to run camera in
flickerless mode.

8
EXPOSURE BLC (Backlight Compensation)
Backlight Compensation prevents
subjects in defined areas of the scene
from appearing too dark when
backlighting is present.
Select ON or OFF.
If ON is selected, you can adjust the BLC
level in five areas of the scene (top,
bottom, center, left, right).
Select a value from 0to 255 for each area.
Increase the BLC level in the areas you
want to lighten.

Document 800-08379 Rev B 9
05/11
EXPOSURE MAX_DR (Maximum Dynamic Range)
Maximum Dynamic Range provides
clear images even when strong
backlighting is present.
Select ON or OFF.
If ON is selected, you can adjust the
MAX_DR level.
Select a value from 0to 20.

10
EXPOSURE AGC (Auto Gain Control)
EXPOSURE SENSE_UP
Auto Gain Control automatically adjusts
the video gain to enhance picture
brightness in low light conditions.
Select one of the following settings:
•OFF
•LOW
• MIDDLE
•HIGH
Sense Up automatically activates slow
shutter function when a scene is too dark.
Select a value from X2 to X256 to set the
frame integration level.
Note The SENSE_UP menu cannot be
controlled if the E.SHUTTER
setting is above 1/250.

Document 800-08379 Rev B 11
05/11
Color Menu
COLOR WB MODE (White Balance)
To set the white balance mode, select one of the
following:
•AWC - Auto White Balance Control mode
compensates for color temperature changes
between 2000 K and 18000 K.
•ATW - Auto Tracking White Balance mode
compensates for color temperature changes
between 2500 K and 9500 K.
•MANUAL - Manual mode lets you control the
white balance manually (see below).
•PUSH LOCK - Push Lock mode fixes the
white balance based on current lighting. For
best results, place a white surface (such as a
piece of paper) in front of camera during
adjustment.

12
COLOR WB MODE
COLOR R-Y GAIN AND B-Y GAIN
If WB mode is set to
MANUAL, you can
manually adjust the
red level (M.WB R)
and the blue level
(M.WB B).
Select a value from 0
to 255.
R-Y GAIN sets the
amount of red in the
image. B-Y GAIN sets
the amount of blue in
the image.
Select a value from 0
to 255.


Document 800-08379 Rev B 13
05/11
Day&Night Menu
DAY&NIGHT D&N MODE (True Day/Night)
To set the True Day/Night mode, select one of the
following:
•AUTO - Camera automatically switches between
day and night mode depending on the light level.
•COLOR - Camera remains in day mode, regardless
of light level.
•B/W - Camera remains in night mode, regardless of
light level.
If AUTO is selected, you can define the following
settings:
• BURST - Select ON or OFF. If ON is selected, the
camera provides a color burst signal when in night
mode. If OFF, no color burst signal is provided.
Note Some DVRs require a color burst signal to
detect a camera.
• COLOR BW - Relative light level at which
camera switches from day mode (color) to night
mode (black and white). The higher the number,
the lower the light level.
•BW
COLOR - Relative light level at which
camera switches from night mode (black and
white) to day mode (color). This number should
always be lower than the COLOR BW value.
• READ TIME - Time interval delay before switching
from day mode to night mode. Adjustable from
3secondsto 12 seconds.

14
Function Menu
FUNCTION MIRROR
FUNCTION SHARPNESS
Select one of the following settings:
•OFF
•MIRROR - Flips the image
horizontally
•V-FLIP - Flips the image vertically
•ROTATE - Combines V-FLIP and
MIRROR
To set the image sharpness, select a
value from 0to 49 (49 = sharpest).

Document 800-08379 Rev B 15
05/11
FUNCTION GAMMA
FUNCTION 3D DNR (Digital Noise Reduction)
Select the desired gamma level:
• 0.45 (default)
•0.6
•1.0
Digital Noise Reduction reduces the
noise/distortion on the screen at night,
allowing clear images in low light
conditions.
Select one of the following settings:
•OFF
•LOW
• MIDDLE
•HIGH

16
FUNCTION D_ZOOM (Digital Zoom)
Digital Zoom lets you magnify the image on
the screen up to three times.
Select ON or OFF.
If ON is selected, you can define the following
settings:
• ZOOM - Adjustable from X1.0 to X3.0
(X3.0 =× 3 digital zoom)
•PAN-Panleft(<0) or right (>0)
•TILT-Tiltup(<0) or down (>0)
• SHOW POS. - Select ON or OFF. If ON is
selected, a frame appears on the bottom
right side of the screen showing how the
zoom, pan, and tilt are applied.

Document 800-08379 Rev B 17
05/11
FUNCTION SLC (Side Light Compensation)
Side Light Compensation compensates
for a brighter image on the sides of the
screen.
Select ON or OFF.
If ON is selected, you can adjust the
brightness level. Adjust the brightness
level by selecting a value from 0to 50.

18
FUNCTION HME (Highlight Masking Exposure)
Highlight Masking Exposure masks
highlights, allowing objects to appear
more clearly on the screen.
Select ON or OFF.
If ON is selected, you can adjust the
HME level. Adjust the HME level by
selecting a value from 0to 60. The
higher the number, the darker the
masking will be.

Document 800-08379 Rev B 19
05/11
FUNCTION DIS (Digital Image Stabilization)
Digital Image Stabilization minimizes or
prevents blurred images due to camera
vibration.
Select ON or OFF.

20
Motion Menu
MOTION MOTION
You can set the camera to detect
movement and to display an alarm on the
screen when movement is detected.
Select ON or OFF.
If ON is selected, set the range of cells for
motion detection. Selected cells appear
blue. Unselected cells appear yellow.
•SET WINDOW - Select from 1 to 240
cells for motion detection.
•ALL SET - Set entire image for
motion detection.
•ALL CLEAR - Cancel all motion
detection.